/*- * SPDX-License-Identifier: BSD-2-Clause-FreeBSD * * Copyright (c) 2006 Uwe Stuehler * Copyright (c) 2012 Stefan Sperling * Copyright (c) 2020 Henri Hennebert * Copyright (c) 2020 Gary Jennejohn * Copyright (c) 2020 Jesper Schmitz Mouridsen * All rights reserved. * * Patch from: * - Lutz Bichler * * Base on OpenBSD /sys/dev/pci/rtsx_pci.c & /dev/ic/rtsx.c * on Linux /drivers/mmc/host/rtsx_pci_sdmmc.c, * /include/linux/rtsx_pci.h & * /drivers/misc/cardreader/rtsx_pcr.c * on NetBSD /sys/dev/ic/rtsx.c * * Permission to use, copy, modify, and distribute this software for any * purpose with or without fee is hereby granted, provided that the above * copyright notice and this permission notice appear in all copies. * * THIS SOFTWARE IS PROVIDED BY THE AUTHOR AND CONTRIBUTORS ``AS IS'' AND * ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE * ARE DISCLAIMED. IN NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS * OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY * OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF * SUCH DAMAGE. */ #include __FBSDID("$FreeBSD$"); #include #include #include /* For FreeBSD 11 */ #include /* For FreeBSD 11 */ #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include "opt_mmccam.h" #ifdef MMCCAM #include #include #include #include #include #include #include "mmc_sim_if.h" #endif /* MMCCAM */ #include "rtsxreg.h" /* The softc holds our per-instance data. */ struct rtsx_softc { struct mtx rtsx_mtx; /* device mutex */ device_t rtsx_dev; /* device */ uint16_t rtsx_flags; /* device flags */ uint16_t rtsx_device_id; /* device ID */ device_t rtsx_mmc_dev; /* device of mmc bus */ uint32_t rtsx_intr_enabled; /* enabled interrupts */ uint32_t rtsx_intr_status; /* soft interrupt status */ int rtsx_irq_res_id; /* bus IRQ resource id */ struct resource *rtsx_irq_res; /* bus IRQ resource */ void *rtsx_irq_cookie; /* bus IRQ resource cookie */ struct callout rtsx_timeout_callout; /* callout for timeout */ int rtsx_timeout_cmd; /* interrupt timeout for setup commands */ int rtsx_timeout_io; /* interrupt timeout for I/O commands */ void (*rtsx_intr_trans_ok)(struct rtsx_softc *sc); /* function to call if transfer succeed */ void (*rtsx_intr_trans_ko)(struct rtsx_softc *sc); /* function to call if transfer fail */ struct timeout_task rtsx_card_insert_task; /* card insert delayed task */ struct task rtsx_card_remove_task; /* card remove task */ int rtsx_mem_res_id; /* bus memory resource id */ struct resource *rtsx_mem_res; /* bus memory resource */ bus_space_tag_t rtsx_mem_btag; /* host register set tag */ bus_space_handle_t rtsx_mem_bhandle; /* host register set handle */ bus_dma_tag_t rtsx_cmd_dma_tag; /* DMA tag for command transfer */ bus_dmamap_t rtsx_cmd_dmamap; /* DMA map for command transfer */ void *rtsx_cmd_dmamem; /* DMA mem for command transfer */ bus_addr_t rtsx_cmd_buffer; /* device visible address of the DMA segment */ int rtsx_cmd_index; /* index in rtsx_cmd_buffer */ bus_dma_tag_t rtsx_data_dma_tag; /* DMA tag for data transfer */ bus_dmamap_t rtsx_data_dmamap; /* DMA map for data transfer */ void *rtsx_data_dmamem; /* DMA mem for data transfer */ bus_addr_t rtsx_data_buffer; /* device visible address of the DMA segment */ #ifdef MMCCAM union ccb *rtsx_ccb; /* CAM control block */ struct mmc_sim rtsx_mmc_sim; /* CAM generic sim */ struct mmc_request rtsx_cam_req; /* CAM MMC request */ #endif /* MMCCAM */ struct mmc_request *rtsx_req; /* MMC request */ struct mmc_host rtsx_host; /* host parameters */ int rtsx_pcie_cap; /* PCIe capability offset */ int8_t rtsx_bus_busy; /* bus busy status */ int8_t rtsx_ios_bus_width; /* current host.ios.bus_width */ int32_t rtsx_ios_clock; /* current host.ios.clock */ int8_t rtsx_ios_power_mode; /* current host.ios.power mode */ int8_t rtsx_ios_timing; /* current host.ios.timing */ int8_t rtsx_ios_vccq; /* current host.ios.vccq */ uint8_t rtsx_read_only; /* card read only status */ uint8_t rtsx_inversion; /* inversion of card detection and read only status */ uint8_t rtsx_force_timing; /* force bus_timing_uhs_sdr50 */ uint8_t rtsx_debug_mask; /* debugging mask */ #define RTSX_DEBUG_BASIC 0x01 /* debug basic flow */ #define RTSX_TRACE_SD_CMD 0x02 /* trace SD commands */ #define RTSX_DEBUG_TUNING 0x04 /* debug tuning */ #ifdef MMCCAM uint8_t rtsx_cam_status; /* CAM status - 1 if card in use */ #endif /* MMCCAM */ uint64_t rtsx_read_count; /* count of read operations */ uint64_t rtsx_write_count; /* count of write operations */ bool rtsx_discovery_mode; /* are we in discovery mode? */ bool rtsx_tuning_mode; /* are we tuning */ bool rtsx_double_clk; /* double clock freqency */ bool rtsx_vpclk; /* voltage at Pulse-width Modulation(PWM) clock? */ uint8_t rtsx_ssc_depth; /* Spread spectrum clocking depth */ uint8_t rtsx_card_drive_sel; /* value for RTSX_CARD_DRIVE_SEL */ uint8_t rtsx_sd30_drive_sel_3v3;/* value for RTSX_SD30_DRIVE_SEL */ }; /* rtsx_flags values */ #define RTSX_F_DEFAULT 0x0000 #define RTSX_F_CARD_PRESENT 0x0001 #define RTSX_F_SDIO_SUPPORT 0x0002 #define RTSX_F_VERSION_A 0x0004 #define RTSX_F_VERSION_B 0x0008 #define RTSX_F_VERSION_C 0x0010 #define RTSX_F_VERSION_D 0x0020 #define RTSX_F_8411B_QFN48 0x0040 #define RTSX_F_REVERSE_SOCKET 0x0080 #define RTSX_REALTEK 0x10ec #define RTSX_RTS5209 0x5209 #define RTSX_RTS5227 0x5227 #define RTSX_RTS5229 0x5229 #define RTSX_RTS522A 0x522a #define RTSX_RTS525A 0x525a #define RTSX_RTS5249 0x5249 #define RTSX_RTS5260 0x5260 #define RTSX_RTL8402 0x5286 #define RTSX_RTL8411 0x5289 #define RTSX_RTL8411B 0x5287 #define RTSX_VERSION "2.1g" static const struct rtsx_device { uint16_t vendor_id; uint16_t device_id; const char *desc; } rtsx_devices[] = { { RTSX_REALTEK, RTSX_RTS5209, RTSX_VERSION " Realtek RTS5209 PCIe SD Card Reader"}, { RTSX_REALTEK, RTSX_RTS5227, RTSX_VERSION " Realtek RTS5227 PCIe SD Card Reader"}, { RTSX_REALTEK, RTSX_RTS5229, RTSX_VERSION " Realtek RTS5229 PCIe SD Card Reader"}, { RTSX_REALTEK, RTSX_RTS522A, RTSX_VERSION " Realtek RTS522A PCIe SD Card Reader"}, { RTSX_REALTEK, RTSX_RTS525A, RTSX_VERSION " Realtek RTS525A PCIe SD Card Reader"}, { RTSX_REALTEK, RTSX_RTS5249, RTSX_VERSION " Realtek RTS5249 PCIe SD Card Reader"}, { RTSX_REALTEK, RTSX_RTS5260, RTSX_VERSION " Realtek RTS5260 PCIe SD Card Reader"}, { RTSX_REALTEK, RTSX_RTL8402, RTSX_VERSION " Realtek RTL8402 PCIe SD Card Reader"}, { RTSX_REALTEK, RTSX_RTL8411, RTSX_VERSION " Realtek RTL8411 PCIe SD Card Reader"}, { RTSX_REALTEK, RTSX_RTL8411B, RTSX_VERSION " Realtek RTL8411B PCIe SD Card Reader"}, { 0, 0, NULL} }; /* See `kenv | grep smbios.system` */ static const struct rtsx_inversion_model { char *maker; char *family; char *product; } rtsx_inversion_models[] = { { "LENOVO", "ThinkPad T470p", "20J7S0PM00"}, { NULL, NULL, NULL} }; static int rtsx_dma_alloc(struct rtsx_softc *sc); static void rtsx_dmamap_cb(void *arg, bus_dma_segment_t *segs, int nsegs, int error); static void rtsx_dma_free(struct rtsx_softc *sc); static void rtsx_intr(void *arg); static void rtsx_handle_card_present(struct rtsx_softc *sc); static void rtsx_card_task(void *arg, int pending __unused); static bool rtsx_is_card_present(struct rtsx_softc *sc); static int rtsx_init(struct rtsx_softc *sc); static int rtsx_map_sd_drive(int index); static int rtsx_rts5227_fill_driving(struct rtsx_softc *sc); static int rtsx_rts5249_fill_driving(struct rtsx_softc *sc); static int rtsx_rts5260_fill_driving(struct rtsx_softc *sc); static int rtsx_read(struct rtsx_softc *, uint16_t, uint8_t *); static int rtsx_read_cfg(struct rtsx_softc *sc, uint8_t func, uint16_t addr, uint32_t *val); static int rtsx_write(struct rtsx_softc *sc, uint16_t addr, uint8_t mask, uint8_t val); static int rtsx_read_phy(struct rtsx_softc *sc, uint8_t addr, uint16_t *val); static int rtsx_write_phy(struct rtsx_softc *sc, uint8_t addr, uint16_t val); static int rtsx_bus_power_off(struct rtsx_softc *sc); static int rtsx_bus_power_on(struct rtsx_softc *sc); static int rtsx_set_bus_width(struct rtsx_softc *sc, enum mmc_bus_width width); static int rtsx_set_sd_timing(struct rtsx_softc *sc, enum mmc_bus_timing timing); static int rtsx_set_sd_clock(struct rtsx_softc *sc, uint32_t freq); static int rtsx_stop_sd_clock(struct rtsx_softc *sc); static int rtsx_switch_sd_clock(struct rtsx_softc *sc, uint8_t clk, uint8_t n, uint8_t div, uint8_t mcu); #ifndef MMCCAM static void rtsx_sd_change_tx_phase(struct rtsx_softc *sc, uint8_t sample_point); static void rtsx_sd_change_rx_phase(struct rtsx_softc *sc, uint8_t sample_point); static void rtsx_sd_tuning_rx_phase(struct rtsx_softc *sc, uint32_t *phase_map); static int rtsx_sd_tuning_rx_cmd(struct rtsx_softc *sc, uint8_t sample_point); static int rtsx_sd_tuning_rx_cmd_wait(struct rtsx_softc *sc, struct mmc_command *cmd); static void rtsx_sd_tuning_rx_cmd_wakeup(struct rtsx_softc *sc); static void rtsx_sd_wait_data_idle(struct rtsx_softc *sc); static uint8_t rtsx_sd_search_final_rx_phase(struct rtsx_softc *sc, uint32_t phase_map); static int rtsx_sd_get_rx_phase_len(uint32_t phase_map, int start_bit); #endif /* !MMCCAM */ #if 0 /* For led */ static int rtsx_led_enable(struct rtsx_softc *sc); static int rtsx_led_disable(struct rtsx_softc *sc); #endif /* For led */ static uint8_t rtsx_response_type(uint16_t mmc_rsp); static void rtsx_init_cmd(struct rtsx_softc *sc, struct mmc_command *cmd); static void rtsx_push_cmd(struct rtsx_softc *sc, uint8_t cmd, uint16_t reg, uint8_t mask, uint8_t data); static void rtsx_set_cmd_data_len(struct rtsx_softc *sc, uint16_t block_cnt, uint16_t byte_cnt); static void rtsx_send_cmd(struct rtsx_softc *sc); static void rtsx_ret_resp(struct rtsx_softc *sc); static void rtsx_set_resp(struct rtsx_softc *sc, struct mmc_command *cmd); static void rtsx_stop_cmd(struct rtsx_softc *sc); static void rtsx_clear_error(struct rtsx_softc *sc); static void rtsx_req_done(struct rtsx_softc *sc); static int rtsx_send_req(struct rtsx_softc *sc, struct mmc_command *cmd); static int rtsx_xfer_short(struct rtsx_softc *sc, struct mmc_command *cmd); static void rtsx_ask_ppbuf_part1(struct rtsx_softc *sc); static void rtsx_get_ppbuf_part1(struct rtsx_softc *sc); static void rtsx_get_ppbuf_part2(struct rtsx_softc *sc); static void rtsx_put_ppbuf_part1(struct rtsx_softc *sc); static void rtsx_put_ppbuf_part2(struct rtsx_softc *sc); static void rtsx_write_ppbuf(struct rtsx_softc *sc); static int rtsx_xfer(struct rtsx_softc *sc, struct mmc_command *cmd); static void rtsx_xfer_begin(struct rtsx_softc *sc); static void rtsx_xfer_start(struct rtsx_softc *sc); static void rtsx_xfer_finish(struct rtsx_softc *sc); static void rtsx_timeout(void *arg); #ifdef MMCCAM static int rtsx_get_tran_settings(device_t dev, struct ccb_trans_settings_mmc *cts); static int rtsx_set_tran_settings(device_t dev, struct ccb_trans_settings_mmc *cts); static int rtsx_cam_request(device_t dev, union ccb *ccb); #endif /* MMCCAM */ static int rtsx_read_ivar(device_t bus, device_t child, int which, uintptr_t *result); static int rtsx_write_ivar(device_t bus, device_t child, int which, uintptr_t value); static int rtsx_mmcbr_update_ios(device_t bus, device_t child __unused); static int rtsx_mmcbr_switch_vccq(device_t bus, device_t child __unused); static int rtsx_mmcbr_request(device_t bus, device_t child __unused, struct mmc_request *req); #ifndef MMCCAM static int rtsx_mmcbr_tune(device_t bus, device_t child __unused, bool hs400 __unused); static int rtsx_mmcbr_retune(device_t bus, device_t child __unused, bool reset __unused); static int rtsx_mmcbr_get_ro(device_t bus, device_t child __unused); static int rtsx_mmcbr_acquire_host(device_t bus, device_t child __unused); static int rtsx_mmcbr_release_host(device_t bus, device_t child __unused); #endif /* !MMCCAM */ static int rtsx_probe(device_t dev); static int rtsx_attach(device_t dev); static int rtsx_detach(device_t dev); static int rtsx_shutdown(device_t dev); static int rtsx_suspend(device_t dev); static int rtsx_resume(device_t dev); #define RTSX_LOCK_INIT(_sc) mtx_init(&(_sc)->rtsx_mtx, \ device_get_nameunit(sc->rtsx_dev), "rtsx", MTX_DEF) #define RTSX_LOCK(_sc) mtx_lock(&(_sc)->rtsx_mtx) #define RTSX_UNLOCK(_sc) mtx_unlock(&(_sc)->rtsx_mtx) #define RTSX_LOCK_DESTROY(_sc) mtx_destroy(&(_sc)->rtsx_mtx) #define RTSX_SDCLK_OFF 0 #define RTSX_SDCLK_250KHZ 250000 #define RTSX_SDCLK_400KHZ 400000 #define RTSX_SDCLK_25MHZ 25000000 #define RTSX_SDCLK_50MHZ 50000000 #define RTSX_SDCLK_100MHZ 100000000 #define RTSX_SDCLK_208MHZ 208000000 #define RTSX_MIN_DIV_N 80 #define RTSX_MAX_DIV_N 208 #define RTSX_MAX_DATA_BLKLEN 512 #define RTSX_DMA_ALIGN 4 #define RTSX_HOSTCMD_MAX 256 #define RTSX_DMA_CMD_BIFSIZE (sizeof(uint32_t) * RTSX_HOSTCMD_MAX) #define RTSX_DMA_DATA_BUFSIZE MAXPHYS #define ISSET(t, f) ((t) & (f)) #define READ4(sc, reg) \ (bus_space_read_4((sc)->rtsx_mem_btag, (sc)->rtsx_mem_bhandle, (reg))) #define WRITE4(sc, reg, val) \ (bus_space_write_4((sc)->rtsx_mem_btag, (sc)->rtsx_mem_bhandle, (reg), (val))) #define RTSX_READ(sc, reg, val) \ do { \ int err = rtsx_read((sc), (reg), (val)); \ if (err) \ return (err); \ } while (0) #define RTSX_WRITE(sc, reg, val) \ do { \ int err = rtsx_write((sc), (reg), 0xff, (val)); \ if (err) \ return (err); \ } while (0) #define RTSX_CLR(sc, reg, bits) \ do { \ int err = rtsx_write((sc), (reg), (bits), 0); \ if (err) \ return (err); \ } while (0) #define RTSX_SET(sc, reg, bits) \ do { \ int err = rtsx_write((sc), (reg), (bits), 0xff);\ if (err) \ return (err); \ } while (0) #define RTSX_BITOP(sc, reg, mask, bits) \ do { \ int err = rtsx_write((sc), (reg), (mask), (bits)); \ if (err) \ return (err); \ } while (0) /* * We use two DMA buffers: a command buffer and a data buffer. * * The command buffer contains a command queue for the host controller, * which describes SD/MMC commands to run, and other parameters. The chip * runs the command queue when a special bit in the RTSX_HCBAR register is * set and signals completion with the RTSX_TRANS_OK_INT interrupt. * Each command is encoded as a 4 byte sequence containing command number * (read, write, or check a host controller register), a register address, * and a data bit-mask and value. * SD/MMC commands which do not transfer any data from/to the card only use * the command buffer. * * The data buffer is used for transfer longer than 512. Data transfer is * controlled via the RTSX_HDBAR register and completion is signalled by * the RTSX_TRANS_OK_INT interrupt. * * The chip is unable to perform DMA above 4GB. */ /* * Main commands in the usual seqence used: * * CMD0 Go idle state * CMD8 Send interface condition * CMD55 Application Command for next ACMD * ACMD41 Send Operation Conditions Register (OCR: voltage profile of the card) * CMD2 Send Card Identification (CID) Register * CMD3 Send relative address * CMD9 Send Card Specific Data (CSD) * CMD13 Send status (32 bits - bit 25: card password protected) * CMD7 Select card (before Get card SCR) * ACMD51 Send SCR (SD CARD Configuration Register - [51:48]: Bus widths supported) * CMD6 SD switch function * ACMD13 Send SD status (512 bits) * ACMD42 Set/Clear card detect * ACMD6 Set bus width * CMD19 Send tuning block * CMD12 Stop transmission * * CMD17 Read single block (<=512) * CMD18 Read multiple blocks (>512) * CMD24 Write single block (<=512) * CMD25 Write multiple blocks (>512) * * CMD52 IO R/W direct * CMD5 Send Operation Conditions */ static int rtsx_dma_alloc(struct rtsx_softc *sc) { int error = 0; error = bus_dma_tag_create(bus_get_dma_tag(sc->rtsx_dev), /* inherit from parent */ RTSX_DMA_ALIGN, 0, /* alignment, boundary */ BUS_SPACE_MAXADDR_32BIT, /* lowaddr */ BUS_SPACE_MAXADDR, /* highaddr */ NULL, NULL, /* filter, filterarg */ RTSX_DMA_CMD_BIFSIZE, 1, /* maxsize, nsegments */ RTSX_DMA_CMD_BIFSIZE, /* maxsegsize */ 0, /* flags */ NULL, NULL, /* lockfunc, lockarg */ &sc->rtsx_cmd_dma_tag); if (error) { device_printf(sc->rtsx_dev, "Can't create cmd parent DMA tag\n"); return (error); } error = bus_dmamem_alloc(sc->rtsx_cmd_dma_tag, /* DMA tag */ &sc->rtsx_cmd_dmamem, /* will hold the KVA pointer */ BUS_DMA_COHERENT | BUS_DMA_WAITOK | BUS_DMA_ZERO, /* flags */ &sc->rtsx_cmd_dmamap); /* DMA map */ if (error) { device_printf(sc->rtsx_dev, "Can't create DMA map for command transfer\n"); goto destroy_cmd_dma_tag; } error = bus_dmamap_load(sc->rtsx_cmd_dma_tag, /* DMA tag */ sc->rtsx_cmd_dmamap, /* DMA map */ sc->rtsx_cmd_dmamem, /* KVA pointer to be mapped */ RTSX_DMA_CMD_BIFSIZE, /* size of buffer */ rtsx_dmamap_cb, /* callback */ &sc->rtsx_cmd_buffer, /* first arg of callback */ 0); /* flags */ if (error || sc->rtsx_cmd_buffer == 0) { device_printf(sc->rtsx_dev, "Can't load DMA memory for command transfer\n"); error = (error) ? error : EFAULT; goto destroy_cmd_dmamem_alloc; } error = bus_dma_tag_create(bus_get_dma_tag(sc->rtsx_dev), /* inherit from parent */ RTSX_DMA_DATA_BUFSIZE, 0, /* alignment, boundary */ BUS_SPACE_MAXADDR_32BIT, /* lowaddr */ BUS_SPACE_MAXADDR, /* highaddr */ NULL, NULL, /* filter, filterarg */ RTSX_DMA_DATA_BUFSIZE, 1, /* maxsize, nsegments */ RTSX_DMA_DATA_BUFSIZE, /* maxsegsize */ 0, /* flags */ NULL, NULL, /* lockfunc, lockarg */ &sc->rtsx_data_dma_tag); if (error) { device_printf(sc->rtsx_dev, "Can't create data parent DMA tag\n"); goto destroy_cmd_dmamap_load; } error = bus_dmamem_alloc(sc->rtsx_data_dma_tag, /* DMA tag */ &sc->rtsx_data_dmamem, /* will hold the KVA pointer */ BUS_DMA_WAITOK | BUS_DMA_ZERO, /* flags */ &sc->rtsx_data_dmamap); /* DMA map */ if (error) { device_printf(sc->rtsx_dev, "Can't create DMA map for data transfer\n"); goto destroy_data_dma_tag; } error = bus_dmamap_load(sc->rtsx_data_dma_tag, /* DMA tag */ sc->rtsx_data_dmamap, /* DMA map */ sc->rtsx_data_dmamem, /* KVA pointer to be mapped */ RTSX_DMA_DATA_BUFSIZE, /* size of buffer */ rtsx_dmamap_cb, /* callback */ &sc->rtsx_data_buffer, /* first arg of callback */ 0); /* flags */ if (error || sc->rtsx_data_buffer == 0) { device_printf(sc->rtsx_dev, "Can't load DMA memory for data transfer\n"); error = (error) ? error : EFAULT; goto destroy_data_dmamem_alloc; } return (error); destroy_data_dmamem_alloc: bus_dmamem_free(sc->rtsx_data_dma_tag, sc->rtsx_data_dmamem, sc->rtsx_data_dmamap); destroy_data_dma_tag: bus_dma_tag_destroy(sc->rtsx_data_dma_tag); destroy_cmd_dmamap_load: bus_dmamap_unload(sc->rtsx_cmd_dma_tag, sc->rtsx_cmd_dmamap); destroy_cmd_dmamem_alloc: bus_dmamem_free(sc->rtsx_cmd_dma_tag, sc->rtsx_cmd_dmamem, sc->rtsx_cmd_dmamap); destroy_cmd_dma_tag: bus_dma_tag_destroy(sc->rtsx_cmd_dma_tag); return (error); } static void rtsx_dmamap_cb(void *arg, bus_dma_segment_t *segs, int nsegs, int error) { if (error) { printf("rtsx_dmamap_cb: error %d\n", error); return; } *(bus_addr_t *)arg = segs[0].ds_addr; } static void rtsx_dma_free(struct rtsx_softc *sc) { if (sc->rtsx_cmd_dma_tag != NULL) { if (sc->rtsx_cmd_dmamap != NULL) bus_dmamap_unload(sc->rtsx_cmd_dma_tag, sc->rtsx_cmd_dmamap); if (sc->rtsx_cmd_dmamem != NULL) bus_dmamem_free(sc->rtsx_cmd_dma_tag, sc->rtsx_cmd_dmamem, sc->rtsx_cmd_dmamap); sc->rtsx_cmd_dmamap = NULL; sc->rtsx_cmd_dmamem = NULL; sc->rtsx_cmd_buffer = 0; bus_dma_tag_destroy(sc->rtsx_cmd_dma_tag); sc->rtsx_cmd_dma_tag = NULL; } if (sc->rtsx_data_dma_tag != NULL) { if (sc->rtsx_data_dmamap != NULL) bus_dmamap_unload(sc->rtsx_data_dma_tag, sc->rtsx_data_dmamap); if (sc->rtsx_data_dmamem != NULL) bus_dmamem_free(sc->rtsx_data_dma_tag, sc->rtsx_data_dmamem, sc->rtsx_data_dmamap); sc->rtsx_data_dmamap = NULL; sc->rtsx_data_dmamem = NULL; sc->rtsx_data_buffer = 0; bus_dma_tag_destroy(sc->rtsx_data_dma_tag); sc->rtsx_data_dma_tag = NULL; } } static void rtsx_intr(void *arg) { struct rtsx_softc *sc = arg; uint32_t enabled; uint32_t status; RTSX_LOCK(sc); enabled = sc->rtsx_intr_enabled; status = READ4(sc, RTSX_BIPR); /* read Bus Interrupt Pending Register */ sc->rtsx_intr_status = status; if (sc->rtsx_debug_mask & RTSX_TRACE_SD_CMD) device_printf(sc->rtsx_dev, "Interrupt handler - enabled: 0x%08x, status: 0x%08x\n", enabled, status); /* Ack interrupts. */ WRITE4(sc, RTSX_BIPR, status); if (((enabled & status) == 0) || status == 0xffffffff) { device_printf(sc->rtsx_dev, "Spurious interrupt - enabled: 0x%08x, status: 0x%08x\n", enabled, status); RTSX_UNLOCK(sc); return; } /* Detect write protect. */ if (status & RTSX_SD_WRITE_PROTECT) sc->rtsx_read_only = 1; else sc->rtsx_read_only = 0; /* Start task to handle SD card status change (from dwmmc.c). */ if (status & RTSX_SD_INT) { device_printf(sc->rtsx_dev, "Interrupt card inserted/removed\n"); rtsx_handle_card_present(sc); } if (sc->rtsx_req == NULL) { RTSX_UNLOCK(sc); return; } if (status & RTSX_TRANS_OK_INT) { sc->rtsx_req->cmd->error = MMC_ERR_NONE; if (sc->rtsx_intr_trans_ok != NULL) sc->rtsx_intr_trans_ok(sc); } else if (status & RTSX_TRANS_FAIL_INT) { uint8_t stat1; sc->rtsx_req->cmd->error = MMC_ERR_FAILED; if (rtsx_read(sc, RTSX_SD_STAT1, &stat1) == 0 && (stat1 & RTSX_SD_CRC_ERR)) { device_printf(sc->rtsx_dev, "CRC error\n"); sc->rtsx_req->cmd->error = MMC_ERR_BADCRC; } if (!sc->rtsx_tuning_mode) device_printf(sc->rtsx_dev, "Transfer fail - status: 0x%08x\n", status); rtsx_stop_cmd(sc); if (sc->rtsx_intr_trans_ko != NULL) sc->rtsx_intr_trans_ko(sc); } RTSX_UNLOCK(sc); } /* * Function called from the IRQ handler (from dwmmc.c). */ static void rtsx_handle_card_present(struct rtsx_softc *sc) { bool was_present; bool is_present; #ifdef MMCCAM was_present = sc->rtsx_cam_status; #else /* !MMCCAM */ was_present = sc->rtsx_mmc_dev != NULL; #endif /* MMCCAM */ is_present = rtsx_is_card_present(sc); if (is_present) device_printf(sc->rtsx_dev, "Card present\n"); else device_printf(sc->rtsx_dev, "Card absent\n"); if (!was_present && is_present) { /* * The delay is to debounce the card insert * (sometimes the card detect pin stabilizes * before the other pins have made good contact). */ taskqueue_enqueue_timeout(taskqueue_swi_giant, &sc->rtsx_card_insert_task, -hz); } else if (was_present && !is_present) { taskqueue_enqueue(taskqueue_swi_giant, &sc->rtsx_card_remove_task); } } /* * This function is called at startup. */ static void rtsx_card_task(void *arg, int pending __unused) { struct rtsx_softc *sc = arg; if (rtsx_is_card_present(sc)) { sc->rtsx_flags |= RTSX_F_CARD_PRESENT; /* Card is present, attach if necessary. */ #ifdef MMCCAM if (sc->rtsx_cam_status == 0) { #else /* !MMCCAM */ if (sc->rtsx_mmc_dev == NULL) { #endif /* MMCCAM */ if (sc->rtsx_debug_mask & RTSX_DEBUG_BASIC) device_printf(sc->rtsx_dev, "Card inserted\n"); sc->rtsx_read_count = sc->rtsx_write_count = 0; #ifdef MMCCAM sc->rtsx_cam_status = 1; mmc_cam_sim_discover(&sc->rtsx_mmc_sim); #else /* !MMCCAM */ RTSX_LOCK(sc); sc->rtsx_mmc_dev = device_add_child(sc->rtsx_dev, "mmc", -1); RTSX_UNLOCK(sc); if (sc->rtsx_mmc_dev == NULL) { device_printf(sc->rtsx_dev, "Adding MMC bus failed\n"); } else { device_set_ivars(sc->rtsx_mmc_dev, sc); device_probe_and_attach(sc->rtsx_mmc_dev); } #endif /* MMCCAM */ } } else { sc->rtsx_flags &= ~RTSX_F_CARD_PRESENT; /* Card isn't present, detach if necessary. */ #ifdef MMCCAM if (sc->rtsx_cam_status != 0) { #else /* !MMCCAM */ if (sc->rtsx_mmc_dev != NULL) { #endif /* MMCCAM */ if (sc->rtsx_debug_mask & RTSX_DEBUG_BASIC) device_printf(sc->rtsx_dev, "Card removed\n"); if (sc->rtsx_debug_mask & RTSX_DEBUG_BASIC) device_printf(sc->rtsx_dev, "Read count: %" PRIu64 ", write count: %" PRIu64 "\n", sc->rtsx_read_count, sc->rtsx_write_count); #ifdef MMCCAM sc->rtsx_cam_status = 0; mmc_cam_sim_discover(&sc->rtsx_mmc_sim); #else /* !MMCCAM */ if (device_delete_child(sc->rtsx_dev, sc->rtsx_mmc_dev)) device_printf(sc->rtsx_dev, "Detaching MMC bus failed\n"); sc->rtsx_mmc_dev = NULL; #endif /* MMCCAM */ } } } static bool rtsx_is_card_present(struct rtsx_softc *sc) { uint32_t status; status = READ4(sc, RTSX_BIPR); if (sc->rtsx_inversion == 0) return (status & RTSX_SD_EXIST); else return !(status & RTSX_SD_EXIST); } static int rtsx_init(struct rtsx_softc *sc) { uint8_t version; uint8_t val; int error; sc->rtsx_host.host_ocr = RTSX_SUPPORTED_VOLTAGE; sc->rtsx_host.f_min = RTSX_SDCLK_250KHZ; sc->rtsx_host.f_max = RTSX_SDCLK_208MHZ; sc->rtsx_host.caps = MMC_CAP_4_BIT_DATA | MMC_CAP_HSPEED | MMC_CAP_UHS_SDR12 | MMC_CAP_UHS_SDR25; sc->rtsx_host.caps |= MMC_CAP_UHS_SDR50 | MMC_CAP_UHS_SDR104; if (sc->rtsx_device_id == RTSX_RTS5209) sc->rtsx_host.caps |= MMC_CAP_8_BIT_DATA; pci_find_cap(sc->rtsx_dev, PCIY_EXPRESS, &(sc->rtsx_pcie_cap)); /* * Check IC version. */ switch (sc->rtsx_device_id) { case RTSX_RTS5229: /* Read IC version from dummy register. */ RTSX_READ(sc, RTSX_DUMMY_REG, &version); if ((version & 0x0F) == RTSX_IC_VERSION_C) sc->rtsx_flags |= RTSX_F_VERSION_C; break; case RTSX_RTS522A: /* Read IC version from dummy register. */ RTSX_READ(sc, RTSX_DUMMY_REG, &version); if ((version & 0x0F) == RTSX_IC_VERSION_A) sc->rtsx_flags |= RTSX_F_VERSION_A; break; case RTSX_RTS525A: /* Read IC version from dummy register. */ RTSX_READ(sc, RTSX_DUMMY_REG, &version); if ((version & 0x0F) == RTSX_IC_VERSION_A) sc->rtsx_flags |= RTSX_F_VERSION_A; break; case RTSX_RTL8411B: RTSX_READ(sc, RTSX_RTL8411B_PACKAGE, &version); if (version & RTSX_RTL8411B_QFN48) sc->rtsx_flags |= RTSX_F_8411B_QFN48; break; } /* * Fetch vendor settings. */ /* * Normally OEMs will set vendor setting to the config space * of Realtek card reader in BIOS stage. This statement reads * the setting and configure the internal registers according * to it, to improve card reader's compatibility condition. */ sc->rtsx_card_drive_sel = RTSX_CARD_DRIVE_DEFAULT; switch (sc->rtsx_device_id) { uint32_t reg; uint32_t reg1; uint8_t reg3; case RTSX_RTS5209: sc->rtsx_card_drive_sel = RTSX_RTS5209_CARD_DRIVE_DEFAULT; sc->rtsx_sd30_drive_sel_3v3 = RTSX_DRIVER_TYPE_D; reg = pci_read_config(sc->rtsx_dev, RTSX_PCR_SETTING_REG2, 4); if (!(reg & 0x80)) { sc->rtsx_card_drive_sel = (reg >> 8) & 0x3F; sc->rtsx_sd30_drive_sel_3v3 = reg & 0x07; } else if (bootverbose || sc->rtsx_debug_mask & RTSX_DEBUG_BASIC) { device_printf(sc->rtsx_dev, "pci_read_config() error - reg: 0x%08x\n", reg); } if (bootverbose || sc->rtsx_debug_mask & RTSX_DEBUG_BASIC) device_printf(sc->rtsx_dev, "card_drive_sel: 0x%02x, sd30_drive_sel_3v3: 0x%02x\n", sc->rtsx_card_drive_sel, sc->rtsx_sd30_drive_sel_3v3); break; case RTSX_RTS5227: case RTSX_RTS522A: sc->rtsx_sd30_drive_sel_3v3 = RTSX_CFG_DRIVER_TYPE_B; reg = pci_read_config(sc->rtsx_dev, RTSX_PCR_SETTING_REG1, 4); if (!(reg & 0x1000000)) { sc->rtsx_card_drive_sel &= 0x3F; sc->rtsx_card_drive_sel |= ((reg >> 25) & 0x01) << 6; reg = pci_read_config(sc->rtsx_dev, RTSX_PCR_SETTING_REG2, 4); sc->rtsx_sd30_drive_sel_3v3 = (reg >> 5) & 0x03; if (reg & 0x4000) sc->rtsx_flags |= RTSX_F_REVERSE_SOCKET; } else if (bootverbose || sc->rtsx_debug_mask & RTSX_DEBUG_BASIC) { device_printf(sc->rtsx_dev, "pci_read_config() error - reg: 0x%08x\n", reg); } if (bootverbose || sc->rtsx_debug_mask & RTSX_DEBUG_BASIC) device_printf(sc->rtsx_dev, "card_drive_sel: 0x%02x, sd30_drive_sel_3v3: 0x%02x, reverse_socket is %s\n", sc->rtsx_card_drive_sel, sc->rtsx_sd30_drive_sel_3v3, (sc->rtsx_flags & RTSX_F_REVERSE_SOCKET) ? "true" : "false"); break; case RTSX_RTS5229: sc->rtsx_sd30_drive_sel_3v3 = RTSX_DRIVER_TYPE_D; reg = pci_read_config(sc->rtsx_dev, RTSX_PCR_SETTING_REG1, 4); if (!(reg & 0x1000000)) { sc->rtsx_card_drive_sel &= 0x3F; sc->rtsx_card_drive_sel |= ((reg >> 25) & 0x01) << 6; reg = pci_read_config(sc->rtsx_dev, RTSX_PCR_SETTING_REG2, 4); sc->rtsx_sd30_drive_sel_3v3 = rtsx_map_sd_drive((reg >> 5) & 0x03); } else if (bootverbose || sc->rtsx_debug_mask & RTSX_DEBUG_BASIC) { device_printf(sc->rtsx_dev, "pci_read_config() error - reg: 0x%08x\n", reg); } if (bootverbose || sc->rtsx_debug_mask & RTSX_DEBUG_BASIC) device_printf(sc->rtsx_dev, "card_drive_sel: 0x%02x, sd30_drive_sel_3v3: 0x%02x\n", sc->rtsx_card_drive_sel, sc->rtsx_sd30_drive_sel_3v3); break; case RTSX_RTS525A: case RTSX_RTS5249: case RTSX_RTS5260: sc->rtsx_sd30_drive_sel_3v3 = RTSX_CFG_DRIVER_TYPE_B; reg = pci_read_config(sc->rtsx_dev, RTSX_PCR_SETTING_REG1, 4); if ((reg & 0x1000000)) { sc->rtsx_card_drive_sel &= 0x3F; sc->rtsx_card_drive_sel |= ((reg >> 25) & 0x01) << 6; reg = pci_read_config(sc->rtsx_dev, RTSX_PCR_SETTING_REG2, 4); sc->rtsx_sd30_drive_sel_3v3 = (reg >> 5) & 0x03; if (reg & 0x4000) sc->rtsx_flags |= RTSX_F_REVERSE_SOCKET; } else if (bootverbose || sc->rtsx_debug_mask & RTSX_DEBUG_BASIC) { device_printf(sc->rtsx_dev, "pci_read_config() error - reg: 0x%08x\n", reg); } if (bootverbose || sc->rtsx_debug_mask & RTSX_DEBUG_BASIC) device_printf(sc->rtsx_dev, "card_drive_sel = 0x%02x, sd30_drive_sel_3v3: 0x%02x, reverse_socket is %s\n", sc->rtsx_card_drive_sel, sc->rtsx_sd30_drive_sel_3v3, (sc->rtsx_flags & RTSX_F_REVERSE_SOCKET) ? "true" : "false"); break; case RTSX_RTL8402: case RTSX_RTL8411: sc->rtsx_card_drive_sel = RTSX_RTL8411_CARD_DRIVE_DEFAULT; sc->rtsx_sd30_drive_sel_3v3 = RTSX_DRIVER_TYPE_D; reg1 = pci_read_config(sc->rtsx_dev, RTSX_PCR_SETTING_REG1, 4); if (reg1 & 0x1000000) { sc->rtsx_card_drive_sel &= 0x3F; sc->rtsx_card_drive_sel |= ((reg1 >> 25) & 0x01) << 6; reg3 = pci_read_config(sc->rtsx_dev, RTSX_PCR_SETTING_REG3, 1); sc->rtsx_sd30_drive_sel_3v3 = (reg3 >> 5) & 0x07; } else if (bootverbose || sc->rtsx_debug_mask & RTSX_DEBUG_BASIC) { device_printf(sc->rtsx_dev, "pci_read_config() error - reg1: 0x%08x\n", reg1); } if (bootverbose || sc->rtsx_debug_mask & RTSX_DEBUG_BASIC) device_printf(sc->rtsx_dev, "card_drive_sel: 0x%02x, sd30_drive_sel_3v3: 0x%02x\n", sc->rtsx_card_drive_sel, sc->rtsx_sd30_drive_sel_3v3); break; case RTSX_RTL8411B: sc->rtsx_card_drive_sel = RTSX_RTL8411_CARD_DRIVE_DEFAULT; sc->rtsx_sd30_drive_sel_3v3 = RTSX_DRIVER_TYPE_D; reg = pci_read_config(sc->rtsx_dev, RTSX_PCR_SETTING_REG1, 4); if (!(reg & 0x1000000)) { sc->rtsx_sd30_drive_sel_3v3 = rtsx_map_sd_drive(reg & 0x03); } else if (bootverbose || sc->rtsx_debug_mask & RTSX_DEBUG_BASIC) { device_printf(sc->rtsx_dev, "pci_read_config() error - reg: 0x%08x\n", reg); } if (bootverbose || sc->rtsx_debug_mask & RTSX_DEBUG_BASIC) device_printf(sc->rtsx_dev, "card_drive_sel: 0x%02x, sd30_drive_sel_3v3: 0x%02x\n", sc->rtsx_card_drive_sel, sc->rtsx_sd30_drive_sel_3v3); break; } if (bootverbose || sc->rtsx_debug_mask & RTSX_DEBUG_BASIC) device_printf(sc->rtsx_dev, "rtsx_init() rtsx_flags: 0x%04x\n", sc->rtsx_flags); /* Enable interrupts. */ sc->rtsx_intr_enabled = RTSX_TRANS_OK_INT_EN | RTSX_TRANS_FAIL_INT_EN | RTSX_SD_INT_EN; WRITE4(sc, RTSX_BIER, sc->rtsx_intr_enabled); /* Power on SSC clock. */ RTSX_CLR(sc, RTSX_FPDCTL, RTSX_SSC_POWER_DOWN); /* Wait SSC power stable. */ DELAY(200); /* Disable ASPM */ val = pci_read_config(sc->rtsx_dev, sc->rtsx_pcie_cap + PCIER_LINK_CTL, 1); pci_write_config(sc->rtsx_dev, sc->rtsx_pcie_cap + PCIER_LINK_CTL, val & 0xfc, 1); /* * Optimize phy. */ switch (sc->rtsx_device_id) { case RTSX_RTS5209: /* Some magic numbers from Linux driver. */ if ((error = rtsx_write_phy(sc, 0x00, 0xB966))) return (error); break; case RTSX_RTS5227: RTSX_CLR(sc, RTSX_PM_CTRL3, RTSX_D3_DELINK_MODE_EN); /* Optimize RX sensitivity. */ if ((error = rtsx_write_phy(sc, 0x00, 0xBA42))) return (error); break; case RTSX_RTS5229: /* Optimize RX sensitivity. */ if ((error = rtsx_write_phy(sc, 0x00, 0xBA42))) return (error); break; case RTSX_RTS522A: RTSX_CLR(sc, RTSX_RTS522A_PM_CTRL3, RTSX_D3_DELINK_MODE_EN); if (sc->rtsx_flags & RTSX_F_VERSION_A) { if ((error = rtsx_write_phy(sc, RTSX_PHY_RCR2, RTSX_PHY_RCR2_INIT_27S))) return (error); } if ((error = rtsx_write_phy(sc, RTSX_PHY_RCR1, RTSX_PHY_RCR1_INIT_27S))) return (error); if ((error = rtsx_write_phy(sc, RTSX_PHY_FLD0, RTSX_PHY_FLD0_INIT_27S))) return (error); if ((error = rtsx_write_phy(sc, RTSX_PHY_FLD3, RTSX_PHY_FLD3_INIT_27S))) return (error); if ((error = rtsx_write_phy(sc, RTSX_PHY_FLD4, RTSX_PHY_FLD4_INIT_27S))) return (error); break; case RTSX_RTS525A: if ((error = rtsx_write_phy(sc, RTSX__PHY_FLD0, RTSX__PHY_FLD0_CLK_REQ_20C | RTSX__PHY_FLD0_RX_IDLE_EN | RTSX__PHY_FLD0_BIT_ERR_RSTN | RTSX__PHY_FLD0_BER_COUNT | RTSX__PHY_FLD0_BER_TIMER | RTSX__PHY_FLD0_CHECK_EN))) return (error); if ((error = rtsx_write_phy(sc, RTSX__PHY_ANA03, RTSX__PHY_ANA03_TIMER_MAX | RTSX__PHY_ANA03_OOBS_DEB_EN | RTSX__PHY_CMU_DEBUG_EN))) return (error); if (sc->rtsx_flags & RTSX_F_VERSION_A) if ((error = rtsx_write_phy(sc, RTSX__PHY_REV0, RTSX__PHY_REV0_FILTER_OUT | RTSX__PHY_REV0_CDR_BYPASS_PFD | RTSX__PHY_REV0_CDR_RX_IDLE_BYPASS))) return (error); break; case RTSX_RTS5249: RTSX_CLR(sc, RTSX_PM_CTRL3, RTSX_D3_DELINK_MODE_EN); if ((error = rtsx_write_phy(sc, RTSX_PHY_REV, RTSX_PHY_REV_RESV | RTSX_PHY_REV_RXIDLE_LATCHED | RTSX_PHY_REV_P1_EN | RTSX_PHY_REV_RXIDLE_EN | RTSX_PHY_REV_CLKREQ_TX_EN | RTSX_PHY_REV_RX_PWST | RTSX_PHY_REV_CLKREQ_DT_1_0 | RTSX_PHY_REV_STOP_CLKRD | RTSX_PHY_REV_STOP_CLKWR))) return (error); DELAY(1000); if ((error = rtsx_write_phy(sc, RTSX_PHY_BPCR, RTSX_PHY_BPCR_IBRXSEL | RTSX_PHY_BPCR_IBTXSEL | RTSX_PHY_BPCR_IB_FILTER | RTSX_PHY_BPCR_CMIRROR_EN))) return (error); if ((error = rtsx_write_phy(sc, RTSX_PHY_PCR, RTSX_PHY_PCR_FORCE_CODE | RTSX_PHY_PCR_OOBS_CALI_50 | RTSX_PHY_PCR_OOBS_VCM_08 | RTSX_PHY_PCR_OOBS_SEN_90 | RTSX_PHY_PCR_RSSI_EN | RTSX_PHY_PCR_RX10K))) return (error); if ((error = rtsx_write_phy(sc, RTSX_PHY_RCR2, RTSX_PHY_RCR2_EMPHASE_EN | RTSX_PHY_RCR2_NADJR | RTSX_PHY_RCR2_CDR_SR_2 | RTSX_PHY_RCR2_FREQSEL_12 | RTSX_PHY_RCR2_CDR_SC_12P | RTSX_PHY_RCR2_CALIB_LATE))) return (error); if ((error = rtsx_write_phy(sc, RTSX_PHY_FLD4, RTSX_PHY_FLD4_FLDEN_SEL | RTSX_PHY_FLD4_REQ_REF | RTSX_PHY_FLD4_RXAMP_OFF | RTSX_PHY_FLD4_REQ_ADDA | RTSX_PHY_FLD4_BER_COUNT | RTSX_PHY_FLD4_BER_TIMER | RTSX_PHY_FLD4_BER_CHK_EN))) return (error); if ((error = rtsx_write_phy(sc, RTSX_PHY_RDR, RTSX_PHY_RDR_RXDSEL_1_9 | RTSX_PHY_SSC_AUTO_PWD))) return (error); if ((error = rtsx_write_phy(sc, RTSX_PHY_RCR1, RTSX_PHY_RCR1_ADP_TIME_4 | RTSX_PHY_RCR1_VCO_COARSE))) return (error); if ((error = rtsx_write_phy(sc, RTSX_PHY_FLD3, RTSX_PHY_FLD3_TIMER_4 | RTSX_PHY_FLD3_TIMER_6 | RTSX_PHY_FLD3_RXDELINK))) return (error); if ((error = rtsx_write_phy(sc, RTSX_PHY_TUNE, RTSX_PHY_TUNE_TUNEREF_1_0 | RTSX_PHY_TUNE_VBGSEL_1252 | RTSX_PHY_TUNE_SDBUS_33 | RTSX_PHY_TUNE_TUNED18 | RTSX_PHY_TUNE_TUNED12 | RTSX_PHY_TUNE_TUNEA12))) return (error); break; } /* Set mcu_cnt to 7 to ensure data can be sampled properly. */ RTSX_BITOP(sc, RTSX_CLK_DIV, 0x07, 0x07); /* Disable sleep mode. */ RTSX_CLR(sc, RTSX_HOST_SLEEP_STATE, RTSX_HOST_ENTER_S1 | RTSX_HOST_ENTER_S3); /* Disable card clock. */ RTSX_CLR(sc, RTSX_CARD_CLK_EN, RTSX_CARD_CLK_EN_ALL); /* Reset delink mode. */ RTSX_CLR(sc, RTSX_CHANGE_LINK_STATE, RTSX_FORCE_RST_CORE_EN | RTSX_NON_STICKY_RST_N_DBG); /* Card driving select. */ RTSX_WRITE(sc, RTSX_CARD_DRIVE_SEL, sc->rtsx_card_drive_sel); /* Enable SSC clock. */ RTSX_WRITE(sc, RTSX_SSC_CTL1, RTSX_SSC_8X_EN | RTSX_SSC_SEL_4M); RTSX_WRITE(sc, RTSX_SSC_CTL2, 0x12); /* Disable cd_pwr_save. */ RTSX_BITOP(sc, RTSX_CHANGE_LINK_STATE, 0x16, RTSX_MAC_PHY_RST_N_DBG); /* Clear Link Ready Interrupt. */ RTSX_BITOP(sc, RTSX_IRQSTAT0, RTSX_LINK_READY_INT, RTSX_LINK_READY_INT); /* Enlarge the estimation window of PERST# glitch * to reduce the chance of invalid card interrupt. */ RTSX_WRITE(sc, RTSX_PERST_GLITCH_WIDTH, 0x80); /* Set RC oscillator to 400K. */ RTSX_CLR(sc, RTSX_RCCTL, RTSX_RCCTL_F_2M); /* Enable interrupt write-clear (default is read-clear). */ RTSX_CLR(sc, RTSX_NFTS_TX_CTRL, RTSX_INT_READ_CLR); switch (sc->rtsx_device_id) { case RTSX_RTS525A: case RTSX_RTS5260: RTSX_BITOP(sc, RTSX_PM_CLK_FORCE_CTL, 1, 1); break; } /* OC power down. */ RTSX_BITOP(sc, RTSX_FPDCTL, RTSX_SD_OC_POWER_DOWN, RTSX_SD_OC_POWER_DOWN); /* Enable clk_request_n to enable clock power management */ pci_write_config(sc->rtsx_dev, sc->rtsx_pcie_cap + PCIER_LINK_CTL + 1, 1, 1); /* Enter L1 when host tx idle */ pci_write_config(sc->rtsx_dev, 0x70F, 0x5B, 1); /* * Specific extra init. */ switch (sc->rtsx_device_id) { uint16_t cap; case RTSX_RTS5209: /* Turn off LED. */ RTSX_WRITE(sc, RTSX_CARD_GPIO, 0x03); /* Reset ASPM state to default value. */ RTSX_CLR(sc, RTSX_ASPM_FORCE_CTL, RTSX_ASPM_FORCE_MASK); /* Force CLKREQ# PIN to drive 0 to request clock. */ RTSX_BITOP(sc, RTSX_PETXCFG, 0x08, 0x08); /* Configure GPIO as output. */ RTSX_WRITE(sc, RTSX_CARD_GPIO_DIR, 0x03); /* Configure driving. */ RTSX_WRITE(sc, RTSX_SD30_CMD_DRIVE_SEL, sc->rtsx_sd30_drive_sel_3v3); break; case RTSX_RTS5227: /* Configure GPIO as output. */ RTSX_BITOP(sc, RTSX_GPIO_CTL, RTSX_GPIO_LED_ON, RTSX_GPIO_LED_ON); /* Reset ASPM state to default value. */ RTSX_BITOP(sc, RTSX_ASPM_FORCE_CTL, RTSX_ASPM_FORCE_MASK, RTSX_FORCE_ASPM_NO_ASPM); /* Switch LDO3318 source from DV33 to 3V3. */ RTSX_CLR(sc, RTSX_LDO_PWR_SEL, RTSX_LDO_PWR_SEL_DV33); RTSX_BITOP(sc, RTSX_LDO_PWR_SEL, RTSX_LDO_PWR_SEL_DV33, RTSX_LDO_PWR_SEL_3V3); /* Set default OLT blink period. */ RTSX_BITOP(sc, RTSX_OLT_LED_CTL, 0x0F, RTSX_OLT_LED_PERIOD); /* Configure LTR. */ cap = pci_read_config(sc->rtsx_dev, sc->rtsx_pcie_cap + PCIER_DEVICE_CTL2, 2); if (cap & PCIEM_CTL2_LTR_ENABLE) RTSX_WRITE(sc, RTSX_LTR_CTL, 0xa3); /* Configure OBFF. */ RTSX_BITOP(sc, RTSX_OBFF_CFG, RTSX_OBFF_EN_MASK, RTSX_OBFF_ENABLE); /* Configure driving. */ if ((error = rtsx_rts5227_fill_driving(sc))) return (error); /* Configure force_clock_req. */ if (sc->rtsx_flags & RTSX_F_REVERSE_SOCKET) RTSX_BITOP(sc, RTSX_PETXCFG, 0xB8, 0xB8); else RTSX_BITOP(sc, RTSX_PETXCFG, 0xB8, 0x88); RTSX_CLR(sc, RTSX_PM_CTRL3, RTSX_D3_DELINK_MODE_EN); /*!!! Added for reboot after Windows. */ RTSX_BITOP(sc, RTSX_PM_CTRL3, RTSX_PM_WAKE_EN, RTSX_PM_WAKE_EN); break; case RTSX_RTS5229: /* Configure GPIO as output. */ RTSX_BITOP(sc, RTSX_GPIO_CTL, RTSX_GPIO_LED_ON, RTSX_GPIO_LED_ON); /* Reset ASPM state to default value. */ /* With this reset: dd if=/dev/random of=/dev/mmcsd0 encounter a timeout. */ //!!! RTSX_BITOP(sc, RTSX_ASPM_FORCE_CTL, RTSX_ASPM_FORCE_MASK, RTSX_FORCE_ASPM_NO_ASPM); /* Force CLKREQ# PIN to drive 0 to request clock. */ RTSX_BITOP(sc, RTSX_PETXCFG, 0x08, 0x08); /* Switch LDO3318 source from DV33 to card_3v3. */ RTSX_CLR(sc, RTSX_LDO_PWR_SEL, RTSX_LDO_PWR_SEL_DV33); RTSX_BITOP(sc, RTSX_LDO_PWR_SEL, RTSX_LDO_PWR_SEL_DV33, RTSX_LDO_PWR_SEL_3V3); /* Set default OLT blink period. */ RTSX_BITOP(sc, RTSX_OLT_LED_CTL, 0x0F, RTSX_OLT_LED_PERIOD); /* Configure driving. */ RTSX_WRITE(sc, RTSX_SD30_CMD_DRIVE_SEL, sc->rtsx_sd30_drive_sel_3v3); break; case RTSX_RTS522A: /* Add specific init from RTS5227. */ /* Configure GPIO as output. */ RTSX_BITOP(sc, RTSX_GPIO_CTL, RTSX_GPIO_LED_ON, RTSX_GPIO_LED_ON); /* Reset ASPM state to default value. */ RTSX_BITOP(sc, RTSX_ASPM_FORCE_CTL, RTSX_ASPM_FORCE_MASK, RTSX_FORCE_ASPM_NO_ASPM); /* Switch LDO3318 source from DV33 to 3V3. */ RTSX_CLR(sc, RTSX_LDO_PWR_SEL, RTSX_LDO_PWR_SEL_DV33); RTSX_BITOP(sc, RTSX_LDO_PWR_SEL, RTSX_LDO_PWR_SEL_DV33, RTSX_LDO_PWR_SEL_3V3); /* Set default OLT blink period. */ RTSX_BITOP(sc, RTSX_OLT_LED_CTL, 0x0F, RTSX_OLT_LED_PERIOD); /* Configure LTR. */ cap = pci_read_config(sc->rtsx_dev, sc->rtsx_pcie_cap + PCIER_DEVICE_CTL2, 2); if (cap & PCIEM_CTL2_LTR_ENABLE) RTSX_WRITE(sc, RTSX_LTR_CTL, 0xa3); /* Configure OBFF. */ RTSX_BITOP(sc, RTSX_OBFF_CFG, RTSX_OBFF_EN_MASK, RTSX_OBFF_ENABLE); /* Configure driving. */ if ((error = rtsx_rts5227_fill_driving(sc))) return (error); /* Configure force_clock_req. */ if (sc->rtsx_flags & RTSX_F_REVERSE_SOCKET) RTSX_BITOP(sc, RTSX_PETXCFG, 0xB8, 0xB8); else RTSX_BITOP(sc, RTSX_PETXCFG, 0xB8, 0x88); RTSX_CLR(sc, RTSX_RTS522A_PM_CTRL3, 0x10); /* specific for RTS522A. */ RTSX_BITOP(sc, RTSX_FUNC_FORCE_CTL, RTSX_FUNC_FORCE_UPME_XMT_DBG, RTSX_FUNC_FORCE_UPME_XMT_DBG); RTSX_BITOP(sc, RTSX_PCLK_CTL, 0x04, 0x04); RTSX_BITOP(sc, RTSX_PM_EVENT_DEBUG, RTSX_PME_DEBUG_0, RTSX_PME_DEBUG_0); RTSX_WRITE(sc, RTSX_PM_CLK_FORCE_CTL, 0x11); break; case RTSX_RTS525A: /* Add specific init from RTS5249. */ /* Rest L1SUB Config. */ RTSX_CLR(sc, RTSX_L1SUB_CONFIG3, 0xff); /* Configure GPIO as output. */ RTSX_BITOP(sc, RTSX_GPIO_CTL, RTSX_GPIO_LED_ON, RTSX_GPIO_LED_ON); /* Reset ASPM state to default value. */ RTSX_BITOP(sc, RTSX_ASPM_FORCE_CTL, RTSX_ASPM_FORCE_MASK, RTSX_FORCE_ASPM_NO_ASPM); /* Switch LDO3318 source from DV33 to 3V3. */ RTSX_CLR(sc, RTSX_LDO_PWR_SEL, RTSX_LDO_PWR_SEL_DV33); RTSX_BITOP(sc, RTSX_LDO_PWR_SEL, RTSX_LDO_PWR_SEL_DV33, RTSX_LDO_PWR_SEL_3V3); /* Set default OLT blink period. */ RTSX_BITOP(sc, RTSX_OLT_LED_CTL, 0x0F, RTSX_OLT_LED_PERIOD); /* Configure driving. */ if ((error = rtsx_rts5249_fill_driving(sc))) return (error); /* Configure force_clock_req. */ if (sc->rtsx_flags & RTSX_F_REVERSE_SOCKET) RTSX_BITOP(sc, RTSX_PETXCFG, 0xB0, 0xB0); else RTSX_BITOP(sc, RTSX_PETXCFG, 0xB0, 0x80); /* Specifc for RTS525A. */ RTSX_BITOP(sc, RTSX_PCLK_CTL, RTSX_PCLK_MODE_SEL, RTSX_PCLK_MODE_SEL); if (sc->rtsx_flags & RTSX_F_VERSION_A) { RTSX_WRITE(sc, RTSX_L1SUB_CONFIG2, RTSX_L1SUB_AUTO_CFG); RTSX_BITOP(sc, RTSX_RREF_CFG, RTSX_RREF_VBGSEL_MASK, RTSX_RREF_VBGSEL_1V25); RTSX_BITOP(sc, RTSX_LDO_VIO_CFG, RTSX_LDO_VIO_TUNE_MASK, RTSX_LDO_VIO_1V7); RTSX_BITOP(sc, RTSX_LDO_DV12S_CFG, RTSX_LDO_D12_TUNE_MASK, RTSX_LDO_D12_TUNE_DF); RTSX_BITOP(sc, RTSX_LDO_AV12S_CFG, RTSX_LDO_AV12S_TUNE_MASK, RTSX_LDO_AV12S_TUNE_DF); RTSX_BITOP(sc, RTSX_LDO_VCC_CFG0, RTSX_LDO_VCC_LMTVTH_MASK, RTSX_LDO_VCC_LMTVTH_2A); RTSX_BITOP(sc, RTSX_OOBS_CONFIG, RTSX_OOBS_AUTOK_DIS | RTSX_OOBS_VAL_MASK, 0x89); } break; case RTSX_RTS5249: /* Rest L1SUB Config. */ RTSX_CLR(sc, RTSX_L1SUB_CONFIG3, 0xff); /* Configure GPIO as output. */ RTSX_BITOP(sc, RTSX_GPIO_CTL, RTSX_GPIO_LED_ON, RTSX_GPIO_LED_ON); /* Reset ASPM state to default value. */ RTSX_BITOP(sc, RTSX_ASPM_FORCE_CTL, RTSX_ASPM_FORCE_MASK, RTSX_FORCE_ASPM_NO_ASPM); /* Switch LDO3318 source from DV33 to 3V3. */ RTSX_CLR(sc, RTSX_LDO_PWR_SEL, RTSX_LDO_PWR_SEL_DV33); RTSX_BITOP(sc, RTSX_LDO_PWR_SEL, RTSX_LDO_PWR_SEL_DV33, RTSX_LDO_PWR_SEL_3V3); /* Set default OLT blink period. */ RTSX_BITOP(sc, RTSX_OLT_LED_CTL, 0x0F, RTSX_OLT_LED_PERIOD); /* Configure driving. */ if ((error = rtsx_rts5249_fill_driving(sc))) return (error); /* Configure force_clock_req. */ if (sc->rtsx_flags & RTSX_F_REVERSE_SOCKET) RTSX_BITOP(sc, RTSX_PETXCFG, 0xB0, 0xB0); else RTSX_BITOP(sc, RTSX_PETXCFG, 0xB0, 0x80); break; case RTSX_RTS5260: /* Set mcu_cnt to 7 to ensure data can be sampled properly. */ RTSX_BITOP(sc, RTSX_CLK_DIV, 0x07, 0x07); RTSX_WRITE(sc, RTSX_SSC_DIV_N_0, 0x5D); /* Force no MDIO */ RTSX_WRITE(sc, RTSX_RTS5260_AUTOLOAD_CFG4, RTSX_RTS5260_MIMO_DISABLE); /* Modify SDVCC Tune Default Parameters! */ RTSX_BITOP(sc, RTSX_LDO_VCC_CFG0, RTSX_RTS5260_DVCC_TUNE_MASK, RTSX_RTS5260_DVCC_33); RTSX_BITOP(sc, RTSX_PCLK_CTL, RTSX_PCLK_MODE_SEL, RTSX_PCLK_MODE_SEL); RTSX_BITOP(sc, RTSX_L1SUB_CONFIG1, RTSX_AUX_CLK_ACTIVE_SEL_MASK, RTSX_MAC_CKSW_DONE); /* Rest L1SUB Config */ RTSX_CLR(sc, RTSX_L1SUB_CONFIG3, 0xFF); RTSX_BITOP(sc, RTSX_PM_CLK_FORCE_CTL, RTSX_CLK_PM_EN, RTSX_CLK_PM_EN); RTSX_WRITE(sc, RTSX_PWD_SUSPEND_EN, 0xFF); RTSX_BITOP(sc, RTSX_PWR_GATE_CTRL, RTSX_PWR_GATE_EN, RTSX_PWR_GATE_EN); RTSX_BITOP(sc, RTSX_REG_VREF, RTSX_PWD_SUSPND_EN, RTSX_PWD_SUSPND_EN); RTSX_BITOP(sc, RTSX_RBCTL, RTSX_U_AUTO_DMA_EN_MASK, RTSX_U_AUTO_DMA_DISABLE); if (sc->rtsx_flags & RTSX_F_REVERSE_SOCKET) RTSX_BITOP(sc, RTSX_PETXCFG, 0xB0, 0xB0); else RTSX_BITOP(sc, RTSX_PETXCFG, 0xB0, 0x80); RTSX_BITOP(sc, RTSX_OBFF_CFG, RTSX_OBFF_EN_MASK, RTSX_OBFF_DISABLE); RTSX_CLR(sc, RTSX_RTS5260_DVCC_CTRL, RTSX_RTS5260_DVCC_OCP_EN | RTSX_RTS5260_DVCC_OCP_CL_EN); /* CLKREQ# PIN will be forced to drive low. */ RTSX_BITOP(sc, RTSX_PETXCFG, RTSX_FORCE_CLKREQ_DELINK_MASK, RTSX_FORCE_CLKREQ_LOW); RTSX_CLR(sc, RTSX_RTS522A_PM_CTRL3, 0x10); break; case RTSX_RTL8402: case RTSX_RTL8411: RTSX_WRITE(sc, RTSX_SD30_CMD_DRIVE_SEL, sc->rtsx_sd30_drive_sel_3v3); RTSX_BITOP(sc, RTSX_CARD_PAD_CTL, RTSX_CD_DISABLE_MASK | RTSX_CD_AUTO_DISABLE, RTSX_CD_ENABLE); break; case RTSX_RTL8411B: if (sc->rtsx_flags & RTSX_F_8411B_QFN48) RTSX_WRITE(sc, RTSX_CARD_PULL_CTL3, 0xf5); RTSX_WRITE(sc, RTSX_SD30_CMD_DRIVE_SEL, sc->rtsx_sd30_drive_sel_3v3); /* Enable SD interrupt. */ RTSX_BITOP(sc, RTSX_CARD_PAD_CTL, RTSX_CD_DISABLE_MASK | RTSX_CD_AUTO_DISABLE, RTSX_CD_ENABLE); /* Clear hw_pfm_en to disable hardware PFM mode. */ RTSX_BITOP(sc, RTSX_FUNC_FORCE_CTL, 0x06, 0x00); break; } /*!!! Added for reboot after Windows. */ rtsx_bus_power_off(sc); rtsx_set_sd_timing(sc, bus_timing_normal); rtsx_set_sd_clock(sc, 0); /*!!! Added for reboot after Windows. */ return (0); } static int rtsx_map_sd_drive(int index) { uint8_t sd_drive[4] = { 0x01, /* Type D */ 0x02, /* Type C */ 0x05, /* Type A */ 0x03 /* Type B */ }; return (sd_drive[index]); } /* For voltage 3v3. */ static int rtsx_rts5227_fill_driving(struct rtsx_softc *sc) { u_char driving_3v3[4][3] = { {0x13, 0x13, 0x13}, {0x96, 0x96, 0x96}, {0x7F, 0x7F, 0x7F}, {0x96, 0x96, 0x96}, }; RTSX_WRITE(sc, RTSX_SD30_CLK_DRIVE_SEL, driving_3v3[sc->rtsx_sd30_drive_sel_3v3][0]); RTSX_WRITE(sc, RTSX_SD30_CMD_DRIVE_SEL, driving_3v3[sc->rtsx_sd30_drive_sel_3v3][1]); RTSX_WRITE(sc, RTSX_SD30_DAT_DRIVE_SEL, driving_3v3[sc->rtsx_sd30_drive_sel_3v3][2]); return (0); } /* For voltage 3v3. */ static int rtsx_rts5249_fill_driving(struct rtsx_softc *sc) { u_char driving_3v3[4][3] = { {0x11, 0x11, 0x18}, {0x55, 0x55, 0x5C}, {0xFF, 0xFF, 0xFF}, {0x96, 0x96, 0x96}, }; RTSX_WRITE(sc, RTSX_SD30_CLK_DRIVE_SEL, driving_3v3[sc->rtsx_sd30_drive_sel_3v3][0]); RTSX_WRITE(sc, RTSX_SD30_CMD_DRIVE_SEL, driving_3v3[sc->rtsx_sd30_drive_sel_3v3][1]); RTSX_WRITE(sc, RTSX_SD30_DAT_DRIVE_SEL, driving_3v3[sc->rtsx_sd30_drive_sel_3v3][2]); return (0); } static int rtsx_rts5260_fill_driving(struct rtsx_softc *sc) { u_char driving_3v3[4][3] = { {0x11, 0x11, 0x11}, {0x22, 0x22, 0x22}, {0x55, 0x55, 0x55}, {0x33, 0x33, 0x33}, }; RTSX_WRITE(sc, RTSX_SD30_CLK_DRIVE_SEL, driving_3v3[sc->rtsx_sd30_drive_sel_3v3][0]); RTSX_WRITE(sc, RTSX_SD30_CMD_DRIVE_SEL, driving_3v3[sc->rtsx_sd30_drive_sel_3v3][1]); RTSX_WRITE(sc, RTSX_SD30_DAT_DRIVE_SEL, driving_3v3[sc->rtsx_sd30_drive_sel_3v3][2]); return (0); } static int rtsx_read(struct rtsx_softc *sc, uint16_t addr, uint8_t *val) { int tries = 1024; uint32_t arg; uint32_t reg; arg = RTSX_HAIMR_BUSY | (uint32_t)((addr & 0x3FFF) << 16); WRITE4(sc, RTSX_HAIMR, arg); while (tries--) { reg = READ4(sc, RTSX_HAIMR); if (!(reg & RTSX_HAIMR_BUSY)) break; } *val = (reg & 0xff); if (tries > 0) { return (0); } else { device_printf(sc->rtsx_dev, "rtsx_read(0x%x) timeout\n", arg); return (ETIMEDOUT); } } static int rtsx_read_cfg(struct rtsx_softc *sc, uint8_t func, uint16_t addr, uint32_t *val) { int tries = 1024; uint8_t data0, data1, data2, data3, rwctl; RTSX_WRITE(sc, RTSX_CFGADDR0, addr); RTSX_WRITE(sc, RTSX_CFGADDR1, addr >> 8); RTSX_WRITE(sc, RTSX_CFGRWCTL, RTSX_CFG_BUSY | (func & 0x03 << 4)); while (tries--) { RTSX_READ(sc, RTSX_CFGRWCTL, &rwctl); if (!(rwctl & RTSX_CFG_BUSY)) break; } if (tries == 0) return (ETIMEDOUT); RTSX_READ(sc, RTSX_CFGDATA0, &data0); RTSX_READ(sc, RTSX_CFGDATA1, &data1); RTSX_READ(sc, RTSX_CFGDATA2, &data2); RTSX_READ(sc, RTSX_CFGDATA3, &data3); *val = (data3 << 24) | (data2 << 16) | (data1 << 8) | data0; return (0); } static int rtsx_write(struct rtsx_softc *sc, uint16_t addr, uint8_t mask, uint8_t val) { int tries = 1024; uint32_t arg; uint32_t reg; arg = RTSX_HAIMR_BUSY | RTSX_HAIMR_WRITE | (uint32_t)(((addr & 0x3FFF) << 16) | (mask << 8) | val); WRITE4(sc, RTSX_HAIMR, arg); while (tries--) { reg = READ4(sc, RTSX_HAIMR); if (!(reg & RTSX_HAIMR_BUSY)) { if (val != (reg & 0xff)) { device_printf(sc->rtsx_dev, "rtsx_write(0x%x) error reg=0x%x\n", arg, reg); return (EIO); } return (0); } } device_printf(sc->rtsx_dev, "rtsx_write(0x%x) timeout\n", arg); return (ETIMEDOUT); } static int rtsx_read_phy(struct rtsx_softc *sc, uint8_t addr, uint16_t *val) { int tries = 100000; uint8_t data0, data1, rwctl; RTSX_WRITE(sc, RTSX_PHY_ADDR, addr); RTSX_WRITE(sc, RTSX_PHY_RWCTL, RTSX_PHY_BUSY | RTSX_PHY_READ); while (tries--) { RTSX_READ(sc, RTSX_PHY_RWCTL, &rwctl); if (!(rwctl & RTSX_PHY_BUSY)) break; } if (tries == 0) return (ETIMEDOUT); RTSX_READ(sc, RTSX_PHY_DATA0, &data0); RTSX_READ(sc, RTSX_PHY_DATA1, &data1); *val = data1 << 8 | data0; return (0); } static int rtsx_write_phy(struct rtsx_softc *sc, uint8_t addr, uint16_t val) { int tries = 100000; uint8_t rwctl; RTSX_WRITE(sc, RTSX_PHY_DATA0, val); RTSX_WRITE(sc, RTSX_PHY_DATA1, val >> 8); RTSX_WRITE(sc, RTSX_PHY_ADDR, addr); RTSX_WRITE(sc, RTSX_PHY_RWCTL, RTSX_PHY_BUSY | RTSX_PHY_WRITE); while (tries--) { RTSX_READ(sc, RTSX_PHY_RWCTL, &rwctl); if (!(rwctl & RTSX_PHY_BUSY)) break; } return ((tries == 0) ? ETIMEDOUT : 0); } /* * Notice that the meaning of RTSX_PWR_GATE_CTRL changes between RTS5209 and * RTS5229. In RTS5209 it is a mask of disabled power gates, while in RTS5229 * it is a mask of *enabled* gates. */ static int rtsx_bus_power_off(struct rtsx_softc *sc) { if (sc->rtsx_debug_mask & RTSX_DEBUG_BASIC) device_printf(sc->rtsx_dev, "rtsx_bus_power_off()\n"); /* Disable SD clock. */ RTSX_CLR(sc, RTSX_CARD_CLK_EN, RTSX_SD_CLK_EN); /* Disable SD output. */ RTSX_CLR(sc, RTSX_CARD_OE, RTSX_SD_OUTPUT_EN); /* Turn off power. */ switch (sc->rtsx_device_id) { case RTSX_RTS5209: RTSX_BITOP(sc, RTSX_CARD_PWR_CTL, RTSX_SD_PWR_MASK | RTSX_PMOS_STRG_MASK, RTSX_SD_PWR_OFF | RTSX_PMOS_STRG_400mA); RTSX_SET(sc, RTSX_PWR_GATE_CTRL, RTSX_LDO3318_OFF); break; case RTSX_RTS5227: case RTSX_RTS5229: case RTSX_RTS522A: RTSX_BITOP(sc, RTSX_CARD_PWR_CTL, RTSX_SD_PWR_MASK | RTSX_PMOS_STRG_MASK, RTSX_SD_PWR_OFF | RTSX_PMOS_STRG_400mA); RTSX_CLR(sc, RTSX_PWR_GATE_CTRL, RTSX_LDO3318_PWR_MASK); break; case RTSX_RTS5260: rtsx_stop_cmd(sc); /* Switch vccq to 330 */ RTSX_BITOP(sc, RTSX_LDO_CONFIG2, RTSX_DV331812_VDD1, RTSX_DV331812_VDD1); RTSX_BITOP(sc, RTSX_LDO_DV18_CFG, RTSX_DV331812_MASK, RTSX_DV331812_33); RTSX_CLR(sc, RTSX_SD_PAD_CTL, RTSX_SD_IO_USING_1V8); rtsx_rts5260_fill_driving(sc); RTSX_BITOP(sc, RTSX_LDO_VCC_CFG1, RTSX_LDO_POW_SDVDD1_MASK, RTSX_LDO_POW_SDVDD1_OFF); RTSX_BITOP(sc, RTSX_LDO_CONFIG2, RTSX_DV331812_POWERON, RTSX_DV331812_POWEROFF); break; case RTSX_RTL8402: case RTSX_RTL8411: case RTSX_RTL8411B: RTSX_BITOP(sc, RTSX_CARD_PWR_CTL, RTSX_BPP_POWER_MASK, RTSX_BPP_POWER_OFF); RTSX_BITOP(sc, RTSX_LDO_CTL, RTSX_BPP_LDO_POWB, RTSX_BPP_LDO_SUSPEND); break; default: RTSX_CLR(sc, RTSX_PWR_GATE_CTRL, RTSX_LDO3318_PWR_MASK); RTSX_SET(sc, RTSX_CARD_PWR_CTL, RTSX_SD_PWR_OFF); RTSX_CLR(sc, RTSX_CARD_PWR_CTL, RTSX_PMOS_STRG_800mA); break; } /* Disable pull control. */ switch (sc->rtsx_device_id) { case RTSX_RTS5209: RTSX_WRITE(sc, RTSX_CARD_PULL_CTL1, RTSX_PULL_CTL_DISABLE12); RTSX_WRITE(sc, RTSX_CARD_PULL_CTL2, RTSX_PULL_CTL_DISABLE12); RTSX_WRITE(sc, RTSX_CARD_PULL_CTL3, RTSX_PULL_CTL_DISABLE3); break; case RTSX_RTS5227: case RTSX_RTS522A: RTSX_WRITE(sc, RTSX_CARD_PULL_CTL2, RTSX_PULL_CTL_DISABLE12); RTSX_WRITE(sc, RTSX_CARD_PULL_CTL3, RTSX_PULL_CTL_DISABLE3); break; case RTSX_RTS5229: RTSX_WRITE(sc, RTSX_CARD_PULL_CTL2, RTSX_PULL_CTL_DISABLE12); if (sc->rtsx_flags & RTSX_F_VERSION_C) RTSX_WRITE(sc, RTSX_CARD_PULL_CTL3, RTSX_PULL_CTL_DISABLE3_TYPE_C); else RTSX_WRITE(sc, RTSX_CARD_PULL_CTL3, RTSX_PULL_CTL_DISABLE3); break; case RTSX_RTS525A: case RTSX_RTS5249: case RTSX_RTS5260: RTSX_WRITE(sc, RTSX_CARD_PULL_CTL1, 0x66); RTSX_WRITE(sc, RTSX_CARD_PULL_CTL2, RTSX_PULL_CTL_DISABLE12); RTSX_WRITE(sc, RTSX_CARD_PULL_CTL3, RTSX_PULL_CTL_DISABLE3); RTSX_WRITE(sc, RTSX_CARD_PULL_CTL4, 0x55); break; case RTSX_RTL8402: case RTSX_RTL8411: RTSX_WRITE(sc, RTSX_CARD_PULL_CTL1, 0x65); RTSX_WRITE(sc, RTSX_CARD_PULL_CTL2, 0x55); RTSX_WRITE(sc, RTSX_CARD_PULL_CTL3, 0x95); RTSX_WRITE(sc, RTSX_CARD_PULL_CTL4, 0x09); RTSX_WRITE(sc, RTSX_CARD_PULL_CTL5, 0x05); RTSX_WRITE(sc, RTSX_CARD_PULL_CTL6, 0x04); break; case RTSX_RTL8411B: if (sc->rtsx_flags & RTSX_F_8411B_QFN48) { RTSX_WRITE(sc, RTSX_CARD_PULL_CTL2, 0x55); RTSX_WRITE(sc, RTSX_CARD_PULL_CTL3, 0xf5); RTSX_WRITE(sc, RTSX_CARD_PULL_CTL6, 0x15); } else { RTSX_WRITE(sc, RTSX_CARD_PULL_CTL1, 0x65); RTSX_WRITE(sc, RTSX_CARD_PULL_CTL2, 0x55); RTSX_WRITE(sc, RTSX_CARD_PULL_CTL3, 0xd5); RTSX_WRITE(sc, RTSX_CARD_PULL_CTL4, 0x59); RTSX_WRITE(sc, RTSX_CARD_PULL_CTL5, 0x55); RTSX_WRITE(sc, RTSX_CARD_PULL_CTL6, 0x15); } break; } return (0); } static int rtsx_bus_power_on(struct rtsx_softc *sc) { if (sc->rtsx_debug_mask & RTSX_DEBUG_BASIC) device_printf(sc->rtsx_dev, "rtsx_bus_power_on()\n"); /* Select SD card. */ RTSX_BITOP(sc, RTSX_CARD_SELECT, 0x07, RTSX_SD_MOD_SEL); RTSX_BITOP(sc, RTSX_CARD_SHARE_MODE, RTSX_CARD_SHARE_MASK, RTSX_CARD_SHARE_48_SD); /* Enable SD clock. */ RTSX_BITOP(sc, RTSX_CARD_CLK_EN, RTSX_SD_CLK_EN, RTSX_SD_CLK_EN); /* Enable pull control. */ switch (sc->rtsx_device_id) { case RTSX_RTS5209: RTSX_WRITE(sc, RTSX_CARD_PULL_CTL1, RTSX_PULL_CTL_ENABLE12); RTSX_WRITE(sc, RTSX_CARD_PULL_CTL2, RTSX_PULL_CTL_ENABLE12); RTSX_WRITE(sc, RTSX_CARD_PULL_CTL3, RTSX_PULL_CTL_ENABLE3); break; case RTSX_RTS5227: case RTSX_RTS522A: RTSX_WRITE(sc, RTSX_CARD_PULL_CTL2, RTSX_PULL_CTL_ENABLE12); RTSX_WRITE(sc, RTSX_CARD_PULL_CTL3, RTSX_PULL_CTL_ENABLE3); break; case RTSX_RTS5229: RTSX_WRITE(sc, RTSX_CARD_PULL_CTL2, RTSX_PULL_CTL_ENABLE12); if (sc->rtsx_flags & RTSX_F_VERSION_C) RTSX_WRITE(sc, RTSX_CARD_PULL_CTL3, RTSX_PULL_CTL_ENABLE3_TYPE_C); else RTSX_WRITE(sc, RTSX_CARD_PULL_CTL3, RTSX_PULL_CTL_ENABLE3); break; case RTSX_RTS525A: case RTSX_RTS5249: case RTSX_RTS5260: RTSX_WRITE(sc, RTSX_CARD_PULL_CTL1, 0x66); RTSX_WRITE(sc, RTSX_CARD_PULL_CTL2, RTSX_PULL_CTL_ENABLE12); RTSX_WRITE(sc, RTSX_CARD_PULL_CTL3, RTSX_PULL_CTL_ENABLE3); RTSX_WRITE(sc, RTSX_CARD_PULL_CTL4, 0xaa); break; case RTSX_RTL8402: case RTSX_RTL8411: RTSX_WRITE(sc, RTSX_CARD_PULL_CTL1, 0xaa); RTSX_WRITE(sc, RTSX_CARD_PULL_CTL2, 0xaa); RTSX_WRITE(sc, RTSX_CARD_PULL_CTL3, 0xa9); RTSX_WRITE(sc, RTSX_CARD_PULL_CTL4, 0x09); RTSX_WRITE(sc, RTSX_CARD_PULL_CTL5, 0x09); RTSX_WRITE(sc, RTSX_CARD_PULL_CTL6, 0x04); break; case RTSX_RTL8411B: if (sc->rtsx_flags & RTSX_F_8411B_QFN48) { RTSX_WRITE(sc, RTSX_CARD_PULL_CTL2, 0xaa); RTSX_WRITE(sc, RTSX_CARD_PULL_CTL3, 0xf9); RTSX_WRITE(sc, RTSX_CARD_PULL_CTL6, 0x19); } else { RTSX_WRITE(sc, RTSX_CARD_PULL_CTL1, 0xaa); RTSX_WRITE(sc, RTSX_CARD_PULL_CTL2, 0xaa); RTSX_WRITE(sc, RTSX_CARD_PULL_CTL3, 0xd9); RTSX_WRITE(sc, RTSX_CARD_PULL_CTL4, 0x59); RTSX_WRITE(sc, RTSX_CARD_PULL_CTL5, 0x55); RTSX_WRITE(sc, RTSX_CARD_PULL_CTL6, 0x15); } break; } /* * To avoid a current peak, enable card power in two phases * with a delay in between. */ switch (sc->rtsx_device_id) { case RTSX_RTS5209: /* Partial power. */ RTSX_BITOP(sc, RTSX_CARD_PWR_CTL, RTSX_SD_PWR_MASK, RTSX_SD_PARTIAL_PWR_ON); RTSX_BITOP(sc, RTSX_PWR_GATE_CTRL, RTSX_LDO3318_PWR_MASK, RTSX_LDO3318_VCC2); DELAY(200); /* Full power. */ RTSX_BITOP(sc, RTSX_CARD_PWR_CTL, RTSX_SD_PWR_MASK, RTSX_SD_PWR_ON); RTSX_BITOP(sc, RTSX_PWR_GATE_CTRL, RTSX_LDO3318_PWR_MASK, RTSX_LDO3318_ON); break; case RTSX_RTS5227: case RTSX_RTS522A: /* Partial power. */ RTSX_BITOP(sc, RTSX_CARD_PWR_CTL, RTSX_SD_PWR_MASK, RTSX_SD_PARTIAL_PWR_ON); RTSX_BITOP(sc, RTSX_PWR_GATE_CTRL, RTSX_LDO3318_PWR_MASK, RTSX_LDO3318_VCC1); DELAY(20000); /* Full power. */ RTSX_BITOP(sc, RTSX_CARD_PWR_CTL, RTSX_SD_PWR_MASK, RTSX_SD_PWR_ON); RTSX_BITOP(sc, RTSX_PWR_GATE_CTRL, RTSX_LDO3318_PWR_MASK, RTSX_LDO3318_VCC1 | RTSX_LDO3318_VCC2); RTSX_BITOP(sc, RTSX_CARD_OE, RTSX_SD_OUTPUT_EN, RTSX_SD_OUTPUT_EN); RTSX_BITOP(sc, RTSX_CARD_OE, RTSX_MS_OUTPUT_EN, RTSX_MS_OUTPUT_EN); break; case RTSX_RTS5229: /* Partial power. */ RTSX_BITOP(sc, RTSX_CARD_PWR_CTL, RTSX_SD_PWR_MASK, RTSX_SD_PARTIAL_PWR_ON); RTSX_BITOP(sc, RTSX_PWR_GATE_CTRL, RTSX_LDO3318_PWR_MASK, RTSX_LDO3318_VCC1); DELAY(200); /* Full power. */ RTSX_BITOP(sc, RTSX_CARD_PWR_CTL, RTSX_SD_PWR_MASK, RTSX_SD_PWR_ON); RTSX_BITOP(sc, RTSX_PWR_GATE_CTRL, RTSX_LDO3318_PWR_MASK, RTSX_LDO3318_VCC1 | RTSX_LDO3318_VCC2); break; case RTSX_RTS525A: RTSX_BITOP(sc, RTSX_LDO_VCC_CFG1, RTSX_LDO_VCC_TUNE_MASK, RTSX_LDO_VCC_3V3); case RTSX_RTS5249: /* Partial power. */ RTSX_BITOP(sc, RTSX_CARD_PWR_CTL, RTSX_SD_PWR_MASK, RTSX_SD_PARTIAL_PWR_ON); RTSX_BITOP(sc, RTSX_PWR_GATE_CTRL, RTSX_LDO3318_PWR_MASK, RTSX_LDO3318_VCC1); DELAY(5000); /* Full power. */ RTSX_BITOP(sc, RTSX_CARD_PWR_CTL, RTSX_SD_PWR_MASK, RTSX_SD_PWR_ON); RTSX_BITOP(sc, RTSX_PWR_GATE_CTRL, RTSX_LDO3318_PWR_MASK, RTSX_LDO3318_VCC1 | RTSX_LDO3318_VCC2); break; case RTSX_RTS5260: RTSX_BITOP(sc, RTSX_LDO_CONFIG2, RTSX_DV331812_VDD1, RTSX_DV331812_VDD1); RTSX_BITOP(sc, RTSX_LDO_VCC_CFG0, RTSX_RTS5260_DVCC_TUNE_MASK, RTSX_RTS5260_DVCC_33); RTSX_BITOP(sc, RTSX_LDO_VCC_CFG1, RTSX_LDO_POW_SDVDD1_MASK, RTSX_LDO_POW_SDVDD1_ON); RTSX_BITOP(sc, RTSX_LDO_CONFIG2, RTSX_DV331812_POWERON, RTSX_DV331812_POWERON); DELAY(20000); RTSX_BITOP(sc, RTSX_SD_CFG1, RTSX_SD_MODE_MASK | RTSX_SD_ASYNC_FIFO_NOT_RST, RTSX_SD30_MODE | RTSX_SD_ASYNC_FIFO_NOT_RST); RTSX_BITOP(sc, RTSX_CLK_CTL, RTSX_CHANGE_CLK, RTSX_CLK_LOW_FREQ); RTSX_WRITE(sc, RTSX_CARD_CLK_SOURCE, RTSX_CRC_VAR_CLK0 | RTSX_SD30_FIX_CLK | RTSX_SAMPLE_VAR_CLK1); RTSX_CLR(sc, RTSX_CLK_CTL, RTSX_CLK_LOW_FREQ); /* Initialize SD_CFG1 register */ RTSX_WRITE(sc, RTSX_SD_CFG1, RTSX_CLK_DIVIDE_128 | RTSX_SD20_MODE); RTSX_WRITE(sc, RTSX_SD_SAMPLE_POINT_CTL, RTSX_SD20_RX_POS_EDGE); RTSX_CLR(sc, RTSX_SD_PUSH_POINT_CTL, 0xff); RTSX_BITOP(sc, RTSX_CARD_STOP, RTSX_SD_STOP | RTSX_SD_CLR_ERR, RTSX_SD_STOP | RTSX_SD_CLR_ERR); /* Reset SD_CFG3 register */ RTSX_CLR(sc, RTSX_SD_CFG3, RTSX_SD30_CLK_END_EN); RTSX_CLR(sc, RTSX_REG_SD_STOP_SDCLK_CFG, RTSX_SD30_CLK_STOP_CFG_EN | RTSX_SD30_CLK_STOP_CFG0 | RTSX_SD30_CLK_STOP_CFG1); RTSX_CLR(sc, RTSX_REG_PRE_RW_MODE, RTSX_EN_INFINITE_MODE); break; case RTSX_RTL8402: case RTSX_RTL8411: case RTSX_RTL8411B: RTSX_BITOP(sc, RTSX_CARD_PWR_CTL, RTSX_BPP_POWER_MASK, RTSX_BPP_POWER_5_PERCENT_ON); RTSX_BITOP(sc, RTSX_LDO_CTL, RTSX_BPP_LDO_POWB, RTSX_BPP_LDO_SUSPEND); DELAY(150); RTSX_BITOP(sc, RTSX_CARD_PWR_CTL, RTSX_BPP_POWER_MASK, RTSX_BPP_POWER_10_PERCENT_ON); DELAY(150); RTSX_BITOP(sc, RTSX_CARD_PWR_CTL, RTSX_BPP_POWER_MASK, RTSX_BPP_POWER_15_PERCENT_ON); DELAY(150); RTSX_BITOP(sc, RTSX_CARD_PWR_CTL, RTSX_BPP_POWER_MASK, RTSX_BPP_POWER_ON); RTSX_BITOP(sc, RTSX_LDO_CTL, RTSX_BPP_LDO_POWB, RTSX_BPP_LDO_ON); break; } /* Enable SD card output. */ RTSX_WRITE(sc, RTSX_CARD_OE, RTSX_SD_OUTPUT_EN); DELAY(200); return (0); } /* * Set but width. */ static int rtsx_set_bus_width(struct rtsx_softc *sc, enum mmc_bus_width width) { uint32_t bus_width; switch (width) { case bus_width_1: bus_width = RTSX_BUS_WIDTH_1; break; case bus_width_4: bus_width = RTSX_BUS_WIDTH_4; break; case bus_width_8: bus_width = RTSX_BUS_WIDTH_8; break; default: return (MMC_ERR_INVALID); } RTSX_BITOP(sc, RTSX_SD_CFG1, RTSX_BUS_WIDTH_MASK, bus_width); if (sc->rtsx_debug_mask & RTSX_DEBUG_BASIC) { char *busw[] = { "1 bit", "4 bits", "8 bits" }; device_printf(sc->rtsx_dev, "Setting bus width to %s\n", busw[bus_width]); } return (0); } static int rtsx_set_sd_timing(struct rtsx_softc *sc, enum mmc_bus_timing timing) { if (timing == bus_timing_hs && sc->rtsx_force_timing) { timing = bus_timing_uhs_sdr50; sc->rtsx_ios_timing = timing; } if (sc->rtsx_debug_mask & RTSX_DEBUG_BASIC) device_printf(sc->rtsx_dev, "rtsx_set_sd_timing(%u)\n", timing); switch (timing) { case bus_timing_uhs_sdr50: case bus_timing_uhs_sdr104: sc->rtsx_double_clk = false; sc->rtsx_vpclk = true; RTSX_BITOP(sc, RTSX_SD_CFG1, 0x0c | RTSX_SD_ASYNC_FIFO_NOT_RST, RTSX_SD30_MODE | RTSX_SD_ASYNC_FIFO_NOT_RST); RTSX_BITOP(sc, RTSX_CLK_CTL, RTSX_CLK_LOW_FREQ, RTSX_CLK_LOW_FREQ); RTSX_WRITE(sc, RTSX_CARD_CLK_SOURCE, RTSX_CRC_VAR_CLK0 | RTSX_SD30_FIX_CLK | RTSX_SAMPLE_VAR_CLK1); RTSX_CLR(sc, RTSX_CLK_CTL, RTSX_CLK_LOW_FREQ); break; case bus_timing_hs: RTSX_BITOP(sc, RTSX_SD_CFG1, RTSX_SD_MODE_MASK, RTSX_SD20_MODE); RTSX_BITOP(sc, RTSX_CLK_CTL, RTSX_CLK_LOW_FREQ, RTSX_CLK_LOW_FREQ); RTSX_WRITE(sc, RTSX_CARD_CLK_SOURCE, RTSX_CRC_FIX_CLK | RTSX_SD30_VAR_CLK0 | RTSX_SAMPLE_VAR_CLK1); RTSX_CLR(sc, RTSX_CLK_CTL, RTSX_CLK_LOW_FREQ); RTSX_BITOP(sc, RTSX_SD_PUSH_POINT_CTL, RTSX_SD20_TX_SEL_MASK, RTSX_SD20_TX_14_AHEAD); RTSX_BITOP(sc, RTSX_SD_SAMPLE_POINT_CTL, RTSX_SD20_RX_SEL_MASK, RTSX_SD20_RX_14_DELAY); break; default: RTSX_BITOP(sc, RTSX_SD_CFG1, RTSX_SD_MODE_MASK, RTSX_SD20_MODE); RTSX_BITOP(sc, RTSX_CLK_CTL, RTSX_CLK_LOW_FREQ, RTSX_CLK_LOW_FREQ); RTSX_WRITE(sc, RTSX_CARD_CLK_SOURCE, RTSX_CRC_FIX_CLK | RTSX_SD30_VAR_CLK0 | RTSX_SAMPLE_VAR_CLK1); RTSX_CLR(sc, RTSX_CLK_CTL, RTSX_CLK_LOW_FREQ); RTSX_WRITE(sc, RTSX_SD_PUSH_POINT_CTL, RTSX_SD20_TX_NEG_EDGE); RTSX_BITOP(sc, RTSX_SD_SAMPLE_POINT_CTL, RTSX_SD20_RX_SEL_MASK, RTSX_SD20_RX_POS_EDGE); break; } return (0); } /* * Set or change SDCLK frequency or disable the SD clock. * Return zero on success. */ static int rtsx_set_sd_clock(struct rtsx_softc *sc, uint32_t freq) { uint8_t clk; uint8_t clk_divider, n, div, mcu; int error = 0; if (sc->rtsx_debug_mask & RTSX_DEBUG_BASIC) device_printf(sc->rtsx_dev, "rtsx_set_sd_clock(%u)\n", freq); if (freq == RTSX_SDCLK_OFF) { error = rtsx_stop_sd_clock(sc); return error; } sc->rtsx_ssc_depth = RTSX_SSC_DEPTH_500K; sc->rtsx_discovery_mode = (freq <= 1000000) ? true : false; if (sc->rtsx_discovery_mode) { /* We use 250k(around) here, in discovery stage. */ clk_divider = RTSX_CLK_DIVIDE_128; freq = 30000000; } else { clk_divider = RTSX_CLK_DIVIDE_0; } RTSX_BITOP(sc, RTSX_SD_CFG1, RTSX_CLK_DIVIDE_MASK, clk_divider); freq /= 1000000; if (sc->rtsx_discovery_mode || !sc->rtsx_double_clk) clk = freq; else clk = freq * 2; switch (sc->rtsx_device_id) { case RTSX_RTL8402: case RTSX_RTL8411: case RTSX_RTL8411B: n = clk * 4 / 5 - 2; break; default: n = clk - 2; break; } if ((clk <= 2) || (n > RTSX_MAX_DIV_N)) return (MMC_ERR_INVALID); mcu = 125 / clk + 3; if (mcu > 15) mcu = 15; /* Make sure that the SSC clock div_n is not less than RTSX_MIN_DIV_N. */ div = RTSX_CLK_DIV_1; while ((n < RTSX_MIN_DIV_N) && (div < RTSX_CLK_DIV_8)) { switch (sc->rtsx_device_id) { case RTSX_RTL8402: case RTSX_RTL8411: case RTSX_RTL8411B: n = (((n + 2) * 5 / 4) * 2) * 4 / 5 - 2; break; default: n = (n + 2) * 2 - 2; break; } div++; } if (sc->rtsx_double_clk && sc->rtsx_ssc_depth > 1) sc->rtsx_ssc_depth -= 1; if (div > RTSX_CLK_DIV_1) { if (sc->rtsx_ssc_depth > (div - 1)) sc->rtsx_ssc_depth -= (div - 1); else sc->rtsx_ssc_depth = RTSX_SSC_DEPTH_4M; } /* Enable SD clock. */ error = rtsx_switch_sd_clock(sc, clk, n, div, mcu); return (error); } static int rtsx_stop_sd_clock(struct rtsx_softc *sc) { RTSX_CLR(sc, RTSX_CARD_CLK_EN, RTSX_CARD_CLK_EN_ALL); RTSX_SET(sc, RTSX_SD_BUS_STAT, RTSX_SD_CLK_FORCE_STOP); return (0); } static int rtsx_switch_sd_clock(struct rtsx_softc *sc, uint8_t clk, uint8_t n, uint8_t div, uint8_t mcu) { if (sc->rtsx_debug_mask & RTSX_DEBUG_BASIC) { device_printf(sc->rtsx_dev, "rtsx_switch_sd_clock() - discovery-mode is %s, ssc_depth: %d\n", (sc->rtsx_discovery_mode) ? "true" : "false", sc->rtsx_ssc_depth); device_printf(sc->rtsx_dev, "rtsx_switch_sd_clock() - clk: %d, n: %d, div: %d, mcu: %d\n", clk, n, div, mcu); } RTSX_BITOP(sc, RTSX_CLK_CTL, RTSX_CLK_LOW_FREQ, RTSX_CLK_LOW_FREQ); RTSX_WRITE(sc, RTSX_CLK_DIV, (div << 4) | mcu); RTSX_CLR(sc, RTSX_SSC_CTL1, RTSX_RSTB); RTSX_BITOP(sc, RTSX_SSC_CTL2, RTSX_SSC_DEPTH_MASK, sc->rtsx_ssc_depth); RTSX_WRITE(sc, RTSX_SSC_DIV_N_0, n); RTSX_BITOP(sc, RTSX_SSC_CTL1, RTSX_RSTB, RTSX_RSTB); if (sc->rtsx_vpclk) { RTSX_CLR(sc, RTSX_SD_VPCLK0_CTL, RTSX_PHASE_NOT_RESET); RTSX_BITOP(sc, RTSX_SD_VPCLK0_CTL, RTSX_PHASE_NOT_RESET, RTSX_PHASE_NOT_RESET); } /* Wait SSC clock stable. */ DELAY(200); RTSX_CLR(sc, RTSX_CLK_CTL, RTSX_CLK_LOW_FREQ); return (0); } #ifndef MMCCAM static void rtsx_sd_change_tx_phase(struct rtsx_softc *sc, uint8_t sample_point) { if (sc->rtsx_debug_mask & RTSX_DEBUG_BASIC) device_printf(sc->rtsx_dev, "rtsx_sd_change_tx_phase() - sample_point: %d\n", sample_point); rtsx_write(sc, RTSX_CLK_CTL, RTSX_CHANGE_CLK, RTSX_CHANGE_CLK); rtsx_write(sc, RTSX_SD_VPCLK0_CTL, RTSX_PHASE_SELECT_MASK, sample_point); rtsx_write(sc, RTSX_SD_VPCLK0_CTL, RTSX_PHASE_NOT_RESET, 0); rtsx_write(sc, RTSX_SD_VPCLK0_CTL, RTSX_PHASE_NOT_RESET, RTSX_PHASE_NOT_RESET); rtsx_write(sc, RTSX_CLK_CTL, RTSX_CHANGE_CLK, 0); rtsx_write(sc, RTSX_SD_CFG1, RTSX_SD_ASYNC_FIFO_NOT_RST, 0); } static void rtsx_sd_change_rx_phase(struct rtsx_softc *sc, uint8_t sample_point) { if (sc->rtsx_debug_mask & RTSX_DEBUG_TUNING) device_printf(sc->rtsx_dev, "rtsx_sd_change_rx_phase() - sample_point: %d\n", sample_point); rtsx_write(sc, RTSX_CLK_CTL, RTSX_CHANGE_CLK, RTSX_CHANGE_CLK); rtsx_write(sc, RTSX_SD_VPCLK1_CTL, RTSX_PHASE_SELECT_MASK, sample_point); rtsx_write(sc, RTSX_SD_VPCLK1_CTL, RTSX_PHASE_NOT_RESET, 0); rtsx_write(sc, RTSX_SD_VPCLK1_CTL, RTSX_PHASE_NOT_RESET, RTSX_PHASE_NOT_RESET); rtsx_write(sc, RTSX_CLK_CTL, RTSX_CHANGE_CLK, 0); rtsx_write(sc, RTSX_SD_CFG1, RTSX_SD_ASYNC_FIFO_NOT_RST, 0); } static void rtsx_sd_tuning_rx_phase(struct rtsx_softc *sc, uint32_t *phase_map) { uint32_t raw_phase_map = 0; int i; int error; for (i = 0; i < RTSX_RX_PHASE_MAX; i++) { error = rtsx_sd_tuning_rx_cmd(sc, (uint8_t)i); if (error == 0) raw_phase_map |= 1 << i; } if (phase_map != NULL) *phase_map = raw_phase_map; } static int rtsx_sd_tuning_rx_cmd(struct rtsx_softc *sc, uint8_t sample_point) { struct mmc_request req = {}; struct mmc_command cmd = {}; int error = 0; cmd.opcode = MMC_SEND_TUNING_BLOCK; cmd.arg = 0; req.cmd = &cmd; RTSX_LOCK(sc); sc->rtsx_req = &req; rtsx_sd_change_rx_phase(sc, sample_point); rtsx_write(sc, RTSX_SD_CFG3, RTSX_SD_RSP_80CLK_TIMEOUT_EN, RTSX_SD_RSP_80CLK_TIMEOUT_EN); rtsx_init_cmd(sc, &cmd); rtsx_set_cmd_data_len(sc, 1, 0x40); rtsx_push_cmd(sc, RTSX_WRITE_REG_CMD, RTSX_SD_CFG2, 0xff, RTSX_SD_CALCULATE_CRC7 | RTSX_SD_CHECK_CRC16 | RTSX_SD_NO_WAIT_BUSY_END | RTSX_SD_CHECK_CRC7 | RTSX_SD_RSP_LEN_6); rtsx_push_cmd(sc, RTSX_WRITE_REG_CMD, RTSX_SD_TRANSFER, 0xff, RTSX_TM_AUTO_TUNING | RTSX_SD_TRANSFER_START); rtsx_push_cmd(sc, RTSX_CHECK_REG_CMD, RTSX_SD_TRANSFER, RTSX_SD_TRANSFER_END, RTSX_SD_TRANSFER_END); /* Set interrupt post processing */ sc->rtsx_intr_trans_ok = rtsx_sd_tuning_rx_cmd_wakeup; sc->rtsx_intr_trans_ko = rtsx_sd_tuning_rx_cmd_wakeup; /* Run the command queue. */ rtsx_send_cmd(sc); error = rtsx_sd_tuning_rx_cmd_wait(sc, &cmd); if (error) { if (sc->rtsx_debug_mask & RTSX_DEBUG_TUNING) device_printf(sc->rtsx_dev, "rtsx_sd_tuning_rx_cmd() - error: %d\n", error); rtsx_sd_wait_data_idle(sc); rtsx_clear_error(sc); } rtsx_write(sc, RTSX_SD_CFG3, RTSX_SD_RSP_80CLK_TIMEOUT_EN, 0); sc->rtsx_req = NULL; RTSX_UNLOCK(sc); return (error); } static int rtsx_sd_tuning_rx_cmd_wait(struct rtsx_softc *sc, struct mmc_command *cmd) { int status; int mask = RTSX_TRANS_OK_INT | RTSX_TRANS_FAIL_INT; status = sc->rtsx_intr_status & mask; while (status == 0) { if (msleep(&sc->rtsx_intr_status, &sc->rtsx_mtx, 0, "rtsxintr", sc->rtsx_timeout_cmd) == EWOULDBLOCK) { cmd->error = MMC_ERR_TIMEOUT; return (MMC_ERR_TIMEOUT); } status = sc->rtsx_intr_status & mask; } return (cmd->error); } static void rtsx_sd_tuning_rx_cmd_wakeup(struct rtsx_softc *sc) { wakeup(&sc->rtsx_intr_status); } static void rtsx_sd_wait_data_idle(struct rtsx_softc *sc) { int i; uint8_t val; for (i = 0; i < 100; i++) { rtsx_read(sc, RTSX_SD_DATA_STATE, &val); if (val & RTSX_SD_DATA_IDLE) return; DELAY(100); } } static uint8_t rtsx_sd_search_final_rx_phase(struct rtsx_softc *sc, uint32_t phase_map) { int start = 0, len = 0; int start_final = 0, len_final = 0; uint8_t final_phase = 0xff; while (start < RTSX_RX_PHASE_MAX) { len = rtsx_sd_get_rx_phase_len(phase_map, start); if (len_final < len) { start_final = start; len_final = len; } start += len ? len : 1; } final_phase = (start_final + len_final / 2) % RTSX_RX_PHASE_MAX; if (sc->rtsx_debug_mask & RTSX_DEBUG_BASIC) device_printf(sc->rtsx_dev, "rtsx_sd_search_final_rx_phase() - phase_map: %x, start_final: %d, len_final: %d, final_phase: %d\n", phase_map, start_final, len_final, final_phase); return final_phase; } static int rtsx_sd_get_rx_phase_len(uint32_t phase_map, int start_bit) { int i; for (i = 0; i < RTSX_RX_PHASE_MAX; i++) { if ((phase_map & (1 << (start_bit + i) % RTSX_RX_PHASE_MAX)) == 0) return i; } return RTSX_RX_PHASE_MAX; } #endif /* !MMCCAM */ #if 0 /* For led */ static int rtsx_led_enable(struct rtsx_softc *sc) { switch (sc->rtsx_device_id) { case RTSX_RTS5209: RTSX_CLR(sc, RTSX_CARD_GPIO, RTSX_CARD_GPIO_LED_OFF); RTSX_WRITE(sc, RTSX_CARD_AUTO_BLINK, RTSX_LED_BLINK_EN | RTSX_LED_BLINK_SPEED); break; case RTSX_RTL8411B: RTSX_CLR(sc, RTSX_GPIO_CTL, 0x01); RTSX_WRITE(sc, RTSX_CARD_AUTO_BLINK, RTSX_LED_BLINK_EN | RTSX_LED_BLINK_SPEED); break; default: RTSX_SET(sc, RTSX_GPIO_CTL, RTSX_GPIO_LED_ON); RTSX_SET(sc, RTSX_OLT_LED_CTL, RTSX_OLT_LED_AUTOBLINK); break; } return (0); } static int rtsx_led_disable(struct rtsx_softc *sc) { switch (sc->rtsx_device_id) { case RTSX_RTS5209: RTSX_CLR(sc, RTSX_CARD_AUTO_BLINK, RTSX_LED_BLINK_EN); RTSX_WRITE(sc, RTSX_CARD_GPIO, RTSX_CARD_GPIO_LED_OFF); break; case RTSX_RTL8411B: RTSX_CLR(sc, RTSX_CARD_AUTO_BLINK, RTSX_LED_BLINK_EN); RTSX_SET(sc, RTSX_GPIO_CTL, 0x01); break; default: RTSX_CLR(sc, RTSX_OLT_LED_CTL, RTSX_OLT_LED_AUTOBLINK); RTSX_CLR(sc, RTSX_GPIO_CTL, RTSX_GPIO_LED_ON); break; } return (0); } #endif /* For led */ static uint8_t rtsx_response_type(uint16_t mmc_rsp) { int i; struct rsp_type { uint16_t mmc_rsp; uint8_t rtsx_rsp; } rsp_types[] = { { MMC_RSP_NONE, RTSX_SD_RSP_TYPE_R0 }, { MMC_RSP_R1, RTSX_SD_RSP_TYPE_R1 }, { MMC_RSP_R1B, RTSX_SD_RSP_TYPE_R1B }, { MMC_RSP_R2, RTSX_SD_RSP_TYPE_R2 }, { MMC_RSP_R3, RTSX_SD_RSP_TYPE_R3 }, { MMC_RSP_R4, RTSX_SD_RSP_TYPE_R4 }, { MMC_RSP_R5, RTSX_SD_RSP_TYPE_R5 }, { MMC_RSP_R6, RTSX_SD_RSP_TYPE_R6 }, { MMC_RSP_R7, RTSX_SD_RSP_TYPE_R7 } }; for (i = 0; i < nitems(rsp_types); i++) { if (mmc_rsp == rsp_types[i].mmc_rsp) return (rsp_types[i].rtsx_rsp); } return (0); } /* * Init command buffer with SD command index and argument. */ static void rtsx_init_cmd(struct rtsx_softc *sc, struct mmc_command *cmd) { sc->rtsx_cmd_index = 0; rtsx_push_cmd(sc, RTSX_WRITE_REG_CMD, RTSX_SD_CMD0, 0xff, RTSX_SD_CMD_START | cmd->opcode); rtsx_push_cmd(sc, RTSX_WRITE_REG_CMD, RTSX_SD_CMD1, 0xff, cmd->arg >> 24); rtsx_push_cmd(sc, RTSX_WRITE_REG_CMD, RTSX_SD_CMD2, 0xff, cmd->arg >> 16); rtsx_push_cmd(sc, RTSX_WRITE_REG_CMD, RTSX_SD_CMD3, 0xff, cmd->arg >> 8); rtsx_push_cmd(sc, RTSX_WRITE_REG_CMD, RTSX_SD_CMD4, 0xff, cmd->arg); } /* * Append a properly encoded host command to the host command buffer. */ static void rtsx_push_cmd(struct rtsx_softc *sc, uint8_t cmd, uint16_t reg, uint8_t mask, uint8_t data) { KASSERT(sc->rtsx_cmd_index < RTSX_HOSTCMD_MAX, ("rtsx: Too many host commands (%d)\n", sc->rtsx_cmd_index)); uint32_t *cmd_buffer = (uint32_t *)(sc->rtsx_cmd_dmamem); cmd_buffer[sc->rtsx_cmd_index++] = htole32((uint32_t)(cmd & 0x3) << 30) | ((uint32_t)(reg & 0x3fff) << 16) | ((uint32_t)(mask) << 8) | ((uint32_t)data); } /* * Queue commands to configure data transfer size. */ static void rtsx_set_cmd_data_len(struct rtsx_softc *sc, uint16_t block_cnt, uint16_t byte_cnt) { rtsx_push_cmd(sc, RTSX_WRITE_REG_CMD, RTSX_SD_BLOCK_CNT_L, 0xff, block_cnt & 0xff); rtsx_push_cmd(sc, RTSX_WRITE_REG_CMD, RTSX_SD_BLOCK_CNT_H, 0xff, block_cnt >> 8); rtsx_push_cmd(sc, RTSX_WRITE_REG_CMD, RTSX_SD_BYTE_CNT_L, 0xff, byte_cnt & 0xff); rtsx_push_cmd(sc, RTSX_WRITE_REG_CMD, RTSX_SD_BYTE_CNT_H, 0xff, byte_cnt >> 8); } /* * Run the command queue. */ static void rtsx_send_cmd(struct rtsx_softc *sc) { if (sc->rtsx_debug_mask & RTSX_TRACE_SD_CMD) device_printf(sc->rtsx_dev, "rtsx_send_cmd()\n"); sc->rtsx_intr_status = 0; /* Sync command DMA buffer. */ bus_dmamap_sync(sc->rtsx_cmd_dma_tag, sc->rtsx_cmd_dmamap, BUS_DMASYNC_PREREAD); bus_dmamap_sync(sc->rtsx_cmd_dma_tag, sc->rtsx_cmd_dmamap, BUS_DMASYNC_PREWRITE); /* Tell the chip where the command buffer is and run the commands. */ WRITE4(sc, RTSX_HCBAR, (uint32_t)sc->rtsx_cmd_buffer); WRITE4(sc, RTSX_HCBCTLR, ((sc->rtsx_cmd_index * 4) & 0x00ffffff) | RTSX_START_CMD | RTSX_HW_AUTO_RSP); } /* * Stop previous command. */ static void rtsx_stop_cmd(struct rtsx_softc *sc) { /* Stop command transfer. */ WRITE4(sc, RTSX_HCBCTLR, RTSX_STOP_CMD); /* Stop DMA transfer. */ WRITE4(sc, RTSX_HDBCTLR, RTSX_STOP_DMA); switch (sc->rtsx_device_id) { case RTSX_RTS5260: rtsx_write(sc, RTSX_RTS5260_DMA_RST_CTL_0, RTSX_RTS5260_DMA_RST | RTSX_RTS5260_ADMA3_RST, RTSX_RTS5260_DMA_RST | RTSX_RTS5260_ADMA3_RST); rtsx_write(sc, RTSX_RBCTL, RTSX_RB_FLUSH, RTSX_RB_FLUSH); break; default: rtsx_write(sc, RTSX_DMACTL, RTSX_DMA_RST, RTSX_DMA_RST); rtsx_write(sc, RTSX_RBCTL, RTSX_RB_FLUSH, RTSX_RB_FLUSH); break; } } /* * Clear error. */ static void rtsx_clear_error(struct rtsx_softc *sc) { /* Clear error. */ rtsx_write(sc, RTSX_CARD_STOP, RTSX_SD_STOP | RTSX_SD_CLR_ERR, RTSX_SD_STOP | RTSX_SD_CLR_ERR); } /* * Signal end of request to mmc/mmcsd. */ static void rtsx_req_done(struct rtsx_softc *sc) { #ifdef MMCCAM union ccb *ccb; #endif /* MMCCAM */ struct mmc_request *req; req = sc->rtsx_req; if (req->cmd->error == MMC_ERR_NONE) { if (req->cmd->opcode == MMC_READ_SINGLE_BLOCK || req->cmd->opcode == MMC_READ_MULTIPLE_BLOCK) sc->rtsx_read_count++; else if (req->cmd->opcode == MMC_WRITE_BLOCK || req->cmd->opcode == MMC_WRITE_MULTIPLE_BLOCK) sc->rtsx_write_count++; } else { rtsx_clear_error(sc); } callout_stop(&sc->rtsx_timeout_callout); sc->rtsx_req = NULL; #ifdef MMCCAM ccb = sc->rtsx_ccb; sc->rtsx_ccb = NULL; ccb->ccb_h.status = (req->cmd->error == 0 ? CAM_REQ_CMP : CAM_REQ_CMP_ERR); xpt_done(ccb); #else /* !MMCCAM */ req->done(req); #endif /* MMCCAM */ } /* * Send request. */ static int rtsx_send_req(struct rtsx_softc *sc, struct mmc_command *cmd) { uint8_t rsp_type; uint16_t reg; if (sc->rtsx_debug_mask & RTSX_TRACE_SD_CMD) device_printf(sc->rtsx_dev, "rtsx_send_req() - CMD%d\n", cmd->opcode); /* Convert response type. */ rsp_type = rtsx_response_type(cmd->flags & MMC_RSP_MASK); if (rsp_type == 0) { device_printf(sc->rtsx_dev, "Unknown rsp_type: 0x%lx\n", (cmd->flags & MMC_RSP_MASK)); cmd->error = MMC_ERR_INVALID; return (MMC_ERR_INVALID); } rtsx_init_cmd(sc, cmd); /* Queue command to set response type. */ rtsx_push_cmd(sc, RTSX_WRITE_REG_CMD, RTSX_SD_CFG2, 0xff, rsp_type); /* Use the ping-pong buffer (cmd buffer) for commands which do not transfer data. */ rtsx_push_cmd(sc, RTSX_WRITE_REG_CMD, RTSX_CARD_DATA_SOURCE, 0x01, RTSX_PINGPONG_BUFFER); /* Queue commands to perform SD transfer. */ rtsx_push_cmd(sc, RTSX_WRITE_REG_CMD, RTSX_SD_TRANSFER, 0xff, RTSX_TM_CMD_RSP | RTSX_SD_TRANSFER_START); rtsx_push_cmd(sc, RTSX_CHECK_REG_CMD, RTSX_SD_TRANSFER, RTSX_SD_TRANSFER_END|RTSX_SD_STAT_IDLE, RTSX_SD_TRANSFER_END|RTSX_SD_STAT_IDLE); /* If needed queue commands to read back card status response. */ if (rsp_type == RTSX_SD_RSP_TYPE_R2) { /* Read data from ping-pong buffer. */ for (reg = RTSX_PPBUF_BASE2; reg < RTSX_PPBUF_BASE2 + 16; reg++) rtsx_push_cmd(sc, RTSX_READ_REG_CMD, reg, 0, 0); } else if (rsp_type != RTSX_SD_RSP_TYPE_R0) { /* Read data from SD_CMDx registers. */ for (reg = RTSX_SD_CMD0; reg <= RTSX_SD_CMD4; reg++) rtsx_push_cmd(sc, RTSX_READ_REG_CMD, reg, 0, 0); } rtsx_push_cmd(sc, RTSX_READ_REG_CMD, RTSX_SD_STAT1, 0, 0); /* Set transfer OK function. */ if (sc->rtsx_intr_trans_ok == NULL) sc->rtsx_intr_trans_ok = rtsx_ret_resp; /* Run the command queue. */ rtsx_send_cmd(sc); return (0); } /* * Return response of previous command (case cmd->data == NULL) and complete resquest. * This Function is called by the interrupt handler via sc->rtsx_intr_trans_ok. */ static void rtsx_ret_resp(struct rtsx_softc *sc) { struct mmc_command *cmd; cmd = sc->rtsx_req->cmd; rtsx_set_resp(sc, cmd); rtsx_req_done(sc); } /* * Set response of previous command. */ static void rtsx_set_resp(struct rtsx_softc *sc, struct mmc_command *cmd) { uint8_t rsp_type; rsp_type = rtsx_response_type(cmd->flags & MMC_RSP_MASK); /* Sync command DMA buffer. */ bus_dmamap_sync(sc->rtsx_cmd_dma_tag, sc->rtsx_cmd_dmamap, BUS_DMASYNC_POSTREAD); bus_dmamap_sync(sc->rtsx_cmd_dma_tag, sc->rtsx_cmd_dmamap, BUS_DMASYNC_POSTWRITE); /* Copy card response into mmc response buffer. */ if (ISSET(cmd->flags, MMC_RSP_PRESENT)) { uint32_t *cmd_buffer = (uint32_t *)(sc->rtsx_cmd_dmamem); if (sc->rtsx_debug_mask & RTSX_TRACE_SD_CMD) { device_printf(sc->rtsx_dev, "cmd_buffer: 0x%08x 0x%08x 0x%08x 0x%08x 0x%08x\n", cmd_buffer[0], cmd_buffer[1], cmd_buffer[2], cmd_buffer[3], cmd_buffer[4]); } if (rsp_type == RTSX_SD_RSP_TYPE_R2) { /* First byte is CHECK_REG_CMD return value, skip it. */ unsigned char *ptr = (unsigned char *)cmd_buffer + 1; int i; /* * The controller offloads the last byte {CRC-7, end bit 1} * of response type R2. Assign dummy CRC, 0, and end bit to this * byte (ptr[16], goes into the LSB of resp[3] later). */ ptr[16] = 0x01; /* The second byte is the status of response, skip it. */ for (i = 0; i < 4; i++) cmd->resp[i] = be32dec(ptr + 1 + i * 4); } else { /* * First byte is CHECK_REG_CMD return value, second * one is the command op code -- we skip those. */ cmd->resp[0] = ((be32toh(cmd_buffer[0]) & 0x0000ffff) << 16) | ((be32toh(cmd_buffer[1]) & 0xffff0000) >> 16); } if (sc->rtsx_debug_mask & RTSX_TRACE_SD_CMD) device_printf(sc->rtsx_dev, "cmd->resp: 0x%08x 0x%08x 0x%08x 0x%08x\n", cmd->resp[0], cmd->resp[1], cmd->resp[2], cmd->resp[3]); } } /* * Use the ping-pong buffer (cmd buffer) for transfer <= 512 bytes. */ static int rtsx_xfer_short(struct rtsx_softc *sc, struct mmc_command *cmd) { int read; if (cmd->data == NULL || cmd->data->len == 0) { cmd->error = MMC_ERR_INVALID; return (MMC_ERR_INVALID); } cmd->data->xfer_len = (cmd->data->len > RTSX_MAX_DATA_BLKLEN) ? RTSX_MAX_DATA_BLKLEN : cmd->data->len; read = ISSET(cmd->data->flags, MMC_DATA_READ); if (sc->rtsx_debug_mask & RTSX_TRACE_SD_CMD) device_printf(sc->rtsx_dev, "rtsx_xfer_short() - %s xfer: %ld bytes with block size %ld\n", read ? "Read" : "Write", (unsigned long)cmd->data->len, (unsigned long)cmd->data->xfer_len); if (cmd->data->len > 512) { device_printf(sc->rtsx_dev, "rtsx_xfer_short() - length too large: %ld > 512\n", (unsigned long)cmd->data->len); cmd->error = MMC_ERR_INVALID; return (MMC_ERR_INVALID); } if (read) { if (sc->rtsx_discovery_mode) rtsx_write(sc, RTSX_SD_CFG1, RTSX_CLK_DIVIDE_MASK, RTSX_CLK_DIVIDE_0); rtsx_init_cmd(sc, cmd); /* Queue commands to configure data transfer size. */ rtsx_set_cmd_data_len(sc, cmd->data->len / cmd->data->xfer_len, cmd->data->xfer_len); /* From Linux: rtsx_pci_sdmmc.c sd_read_data(). */ rtsx_push_cmd(sc, RTSX_WRITE_REG_CMD, RTSX_SD_CFG2, 0xff, RTSX_SD_CALCULATE_CRC7 | RTSX_SD_CHECK_CRC16 | RTSX_SD_NO_WAIT_BUSY_END | RTSX_SD_CHECK_CRC7 | RTSX_SD_RSP_LEN_6); /* Use the ping-pong buffer (cmd buffer). */ rtsx_push_cmd(sc, RTSX_WRITE_REG_CMD, RTSX_CARD_DATA_SOURCE, 0x01, RTSX_PINGPONG_BUFFER); /* Queue commands to perform SD transfer. */ rtsx_push_cmd(sc, RTSX_WRITE_REG_CMD, RTSX_SD_TRANSFER, 0xff, RTSX_TM_NORMAL_READ | RTSX_SD_TRANSFER_START); rtsx_push_cmd(sc, RTSX_CHECK_REG_CMD, RTSX_SD_TRANSFER, RTSX_SD_TRANSFER_END, RTSX_SD_TRANSFER_END); /* Set transfer OK function. */ sc->rtsx_intr_trans_ok = rtsx_ask_ppbuf_part1; /* Run the command queue. */ rtsx_send_cmd(sc); } else { /* Set transfer OK function. */ sc->rtsx_intr_trans_ok = rtsx_put_ppbuf_part1; /* Run the command queue. */ rtsx_send_req(sc, cmd); } return (0); } /* * Use the ping-pong buffer (cmd buffer) for the transfer - first part <= 256 bytes. * This Function is called by the interrupt handler via sc->rtsx_intr_trans_ok. */ static void rtsx_ask_ppbuf_part1(struct rtsx_softc *sc) { struct mmc_command *cmd; uint16_t reg = RTSX_PPBUF_BASE2; int len; int i; cmd = sc->rtsx_req->cmd; len = (cmd->data->len > RTSX_HOSTCMD_MAX) ? RTSX_HOSTCMD_MAX : cmd->data->len; sc->rtsx_cmd_index = 0; for (i = 0; i < len; i++) { rtsx_push_cmd(sc, RTSX_READ_REG_CMD, reg++, 0, 0); } /* Set transfer OK function. */ sc->rtsx_intr_trans_ok = rtsx_get_ppbuf_part1; /* Run the command queue. */ rtsx_send_cmd(sc); } /* * Get the data from the ping-pong buffer (cmd buffer) - first part <= 256 bytes. * This Function is called by the interrupt handler via sc->rtsx_intr_trans_ok. */ static void rtsx_get_ppbuf_part1(struct rtsx_softc *sc) { struct mmc_command *cmd; uint8_t *ptr; int len; cmd = sc->rtsx_req->cmd; ptr = cmd->data->data; len = (cmd->data->len > RTSX_HOSTCMD_MAX) ? RTSX_HOSTCMD_MAX : cmd->data->len; /* Sync command DMA buffer. */ bus_dmamap_sync(sc->rtsx_cmd_dma_tag, sc->rtsx_cmd_dmamap, BUS_DMASYNC_POSTREAD); bus_dmamap_sync(sc->rtsx_cmd_dma_tag, sc->rtsx_cmd_dmamap, BUS_DMASYNC_POSTWRITE); memcpy(ptr, sc->rtsx_cmd_dmamem, len); len = (cmd->data->len > RTSX_HOSTCMD_MAX) ? cmd->data->len - RTSX_HOSTCMD_MAX : 0; /* Use the ping-pong buffer (cmd buffer) for the transfer - second part > 256 bytes. */ if (len > 0) { uint16_t reg = RTSX_PPBUF_BASE2 + RTSX_HOSTCMD_MAX; int i; sc->rtsx_cmd_index = 0; for (i = 0; i < len; i++) { rtsx_push_cmd(sc, RTSX_READ_REG_CMD, reg++, 0, 0); } /* Set transfer OK function. */ sc->rtsx_intr_trans_ok = rtsx_get_ppbuf_part2; /* Run the command queue. */ rtsx_send_cmd(sc); } else { if (sc->rtsx_debug_mask & RTSX_TRACE_SD_CMD && cmd->opcode == ACMD_SEND_SCR) { uint8_t *ptr = cmd->data->data; device_printf(sc->rtsx_dev, "SCR: 0x%02x%02x%02x%02x%02x%02x%02x%02x\n", ptr[0], ptr[1], ptr[2], ptr[3], ptr[4], ptr[5], ptr[6], ptr[7]); } if (sc->rtsx_discovery_mode) rtsx_write(sc, RTSX_SD_CFG1, RTSX_CLK_DIVIDE_MASK, RTSX_CLK_DIVIDE_128); rtsx_req_done(sc); } } /* * Get the data from the ping-pong buffer (cmd buffer) - second part > 256 bytes. * This Function is called by the interrupt handler via sc->rtsx_intr_trans_ok. */ static void rtsx_get_ppbuf_part2(struct rtsx_softc *sc) { struct mmc_command *cmd; uint8_t *ptr; int len; cmd = sc->rtsx_req->cmd; ptr = cmd->data->data; ptr += RTSX_HOSTCMD_MAX; len = cmd->data->len - RTSX_HOSTCMD_MAX; /* Sync command DMA buffer. */ bus_dmamap_sync(sc->rtsx_cmd_dma_tag, sc->rtsx_cmd_dmamap, BUS_DMASYNC_POSTREAD); bus_dmamap_sync(sc->rtsx_cmd_dma_tag, sc->rtsx_cmd_dmamap, BUS_DMASYNC_POSTWRITE); memcpy(ptr, sc->rtsx_cmd_dmamem, len); if (sc->rtsx_discovery_mode) rtsx_write(sc, RTSX_SD_CFG1, RTSX_CLK_DIVIDE_MASK, RTSX_CLK_DIVIDE_128); rtsx_req_done(sc); } /* * Use the ping-pong buffer (cmd buffer) for transfer - first part <= 256 bytes. * This Function is called by the interrupt handler via sc->rtsx_intr_trans_ok. */ static void rtsx_put_ppbuf_part1(struct rtsx_softc *sc) { struct mmc_command *cmd; uint16_t reg = RTSX_PPBUF_BASE2; uint8_t *ptr; int len; int i; cmd = sc->rtsx_req->cmd; ptr = cmd->data->data; len = (cmd->data->len > RTSX_HOSTCMD_MAX) ? RTSX_HOSTCMD_MAX : cmd->data->len; rtsx_set_resp(sc, cmd); sc->rtsx_cmd_index = 0; for (i = 0; i < len; i++) { rtsx_push_cmd(sc, RTSX_WRITE_REG_CMD, reg++, 0xff, *ptr); ptr++; } /* Set transfer OK function. */ if (cmd->data->len > RTSX_HOSTCMD_MAX) sc->rtsx_intr_trans_ok = rtsx_put_ppbuf_part2; else sc->rtsx_intr_trans_ok = rtsx_write_ppbuf; /* Run the command queue. */ rtsx_send_cmd(sc); } /* * Use the ping-pong buffer (cmd buffer) for transfer - second part > 256 bytes. * This Function is called by the interrupt handler via sc->rtsx_intr_trans_ok. */ static void rtsx_put_ppbuf_part2(struct rtsx_softc *sc) { struct mmc_command *cmd; uint16_t reg = RTSX_PPBUF_BASE2 + RTSX_HOSTCMD_MAX; uint8_t *ptr; int len; int i; cmd = sc->rtsx_req->cmd; ptr = cmd->data->data; ptr += RTSX_HOSTCMD_MAX; len = cmd->data->len - RTSX_HOSTCMD_MAX; sc->rtsx_cmd_index = 0; for (i = 0; i < len; i++) { rtsx_push_cmd(sc, RTSX_WRITE_REG_CMD, reg++, 0xff, *ptr); ptr++; } /* Set transfer OK function. */ sc->rtsx_intr_trans_ok = rtsx_write_ppbuf; /* Run the command queue. */ rtsx_send_cmd(sc); } /* * Write the data previously given via the ping-pong buffer on the card. * This Function is called by the interrupt handler via sc->rtsx_intr_trans_ok. */ static void rtsx_write_ppbuf(struct rtsx_softc *sc) { struct mmc_command *cmd; cmd = sc->rtsx_req->cmd; sc->rtsx_cmd_index = 0; /* Queue commands to configure data transfer size. */ rtsx_set_cmd_data_len(sc, cmd->data->len / cmd->data->xfer_len, cmd->data->xfer_len); /* From Linux: rtsx_pci_sdmmc.c sd_write_data(). */ rtsx_push_cmd(sc, RTSX_WRITE_REG_CMD, RTSX_SD_CFG2, 0xff, RTSX_SD_CALCULATE_CRC7 | RTSX_SD_CHECK_CRC16 | RTSX_SD_NO_WAIT_BUSY_END | RTSX_SD_CHECK_CRC7 | RTSX_SD_RSP_LEN_0); rtsx_push_cmd(sc, RTSX_WRITE_REG_CMD, RTSX_SD_TRANSFER, 0xff, RTSX_TM_AUTO_WRITE3 | RTSX_SD_TRANSFER_START); rtsx_push_cmd(sc, RTSX_CHECK_REG_CMD, RTSX_SD_TRANSFER, RTSX_SD_TRANSFER_END, RTSX_SD_TRANSFER_END); /* Set transfer OK function. */ sc->rtsx_intr_trans_ok = rtsx_req_done; /* Run the command queue. */ rtsx_send_cmd(sc); } /* * Use the data buffer for transfer > 512 bytes. */ static int rtsx_xfer(struct rtsx_softc *sc, struct mmc_command *cmd) { int read = ISSET(cmd->data->flags, MMC_DATA_READ); cmd->data->xfer_len = (cmd->data->len > RTSX_MAX_DATA_BLKLEN) ? RTSX_MAX_DATA_BLKLEN : cmd->data->len; if (sc->rtsx_debug_mask & RTSX_TRACE_SD_CMD) device_printf(sc->rtsx_dev, "rtsx_xfer() - %s xfer: %ld bytes with block size %ld\n", read ? "Read" : "Write", (unsigned long)cmd->data->len, (unsigned long)cmd->data->xfer_len); if (cmd->data->len > RTSX_DMA_DATA_BUFSIZE) { device_printf(sc->rtsx_dev, "rtsx_xfer() length too large: %ld > %d\n", (unsigned long)cmd->data->len, RTSX_DMA_DATA_BUFSIZE); cmd->error = MMC_ERR_INVALID; return (MMC_ERR_INVALID); } if (!read) { /* Set transfer OK function. */ sc->rtsx_intr_trans_ok = rtsx_xfer_begin; /* Run the command queue. */ rtsx_send_req(sc, cmd); } else { rtsx_xfer_start(sc); } return (0); } /* * Get request response and start dma data transfer (write command). * This Function is called by the interrupt handler via sc->rtsx_intr_trans_ok. */ static void rtsx_xfer_begin(struct rtsx_softc *sc) { struct mmc_command *cmd; cmd = sc->rtsx_req->cmd; if (sc->rtsx_debug_mask & RTSX_TRACE_SD_CMD) device_printf(sc->rtsx_dev, "rtsx_xfer_begin() - CMD%d\n", cmd->opcode); rtsx_set_resp(sc, cmd); rtsx_xfer_start(sc); } /* * Start dma data transfer. */ static void rtsx_xfer_start(struct rtsx_softc *sc) { struct mmc_command *cmd; int read; uint8_t cfg2; int dma_dir; int tmode; cmd = sc->rtsx_req->cmd; read = ISSET(cmd->data->flags, MMC_DATA_READ); /* Configure DMA transfer mode parameters. */ if (cmd->opcode == MMC_READ_MULTIPLE_BLOCK) cfg2 = RTSX_SD_CHECK_CRC16 | RTSX_SD_NO_WAIT_BUSY_END | RTSX_SD_RSP_LEN_6; else cfg2 = RTSX_SD_CHECK_CRC16 | RTSX_SD_NO_WAIT_BUSY_END | RTSX_SD_RSP_LEN_0; if (read) { dma_dir = RTSX_DMA_DIR_FROM_CARD; /* * Use transfer mode AUTO_READ1, which assume we not * already send the read command and don't need to send * CMD 12 manually after read. */ tmode = RTSX_TM_AUTO_READ1; cfg2 |= RTSX_SD_CALCULATE_CRC7 | RTSX_SD_CHECK_CRC7; rtsx_init_cmd(sc, cmd); } else { dma_dir = RTSX_DMA_DIR_TO_CARD; /* * Use transfer mode AUTO_WRITE3, wich assumes we've already * sent the write command and gotten the response, and will * send CMD 12 manually after writing. */ tmode = RTSX_TM_AUTO_WRITE3; cfg2 |= RTSX_SD_NO_CALCULATE_CRC7 | RTSX_SD_NO_CHECK_CRC7; sc->rtsx_cmd_index = 0; } /* Queue commands to configure data transfer size. */ rtsx_set_cmd_data_len(sc, cmd->data->len / cmd->data->xfer_len, cmd->data->xfer_len); /* Configure DMA controller. */ rtsx_push_cmd(sc, RTSX_WRITE_REG_CMD, RTSX_IRQSTAT0, RTSX_DMA_DONE_INT, RTSX_DMA_DONE_INT); rtsx_push_cmd(sc, RTSX_WRITE_REG_CMD, RTSX_DMATC3, 0xff, cmd->data->len >> 24); rtsx_push_cmd(sc, RTSX_WRITE_REG_CMD, RTSX_DMATC2, 0xff, cmd->data->len >> 16); rtsx_push_cmd(sc, RTSX_WRITE_REG_CMD, RTSX_DMATC1, 0xff, cmd->data->len >> 8); rtsx_push_cmd(sc, RTSX_WRITE_REG_CMD, RTSX_DMATC0, 0xff, cmd->data->len); rtsx_push_cmd(sc, RTSX_WRITE_REG_CMD, RTSX_DMACTL, RTSX_DMA_EN | RTSX_DMA_DIR | RTSX_DMA_PACK_SIZE_MASK, RTSX_DMA_EN | dma_dir | RTSX_DMA_512); /* Use the DMA ring buffer for commands which transfer data. */ rtsx_push_cmd(sc, RTSX_WRITE_REG_CMD, RTSX_CARD_DATA_SOURCE, 0x01, RTSX_RING_BUFFER); /* Queue command to set response type. */ rtsx_push_cmd(sc, RTSX_WRITE_REG_CMD, RTSX_SD_CFG2, 0xff, cfg2); /* Queue commands to perform SD transfer. */ rtsx_push_cmd(sc, RTSX_WRITE_REG_CMD, RTSX_SD_TRANSFER, 0xff, tmode | RTSX_SD_TRANSFER_START); rtsx_push_cmd(sc, RTSX_CHECK_REG_CMD, RTSX_SD_TRANSFER, RTSX_SD_TRANSFER_END, RTSX_SD_TRANSFER_END); /* Run the command queue. */ rtsx_send_cmd(sc); if (!read) memcpy(sc->rtsx_data_dmamem, cmd->data->data, cmd->data->len); /* Sync data DMA buffer. */ bus_dmamap_sync(sc->rtsx_data_dma_tag, sc->rtsx_data_dmamap, BUS_DMASYNC_PREREAD); bus_dmamap_sync(sc->rtsx_data_dma_tag, sc->rtsx_data_dmamap, BUS_DMASYNC_PREWRITE); /* Set transfer OK function. */ sc->rtsx_intr_trans_ok = rtsx_xfer_finish; /* Tell the chip where the data buffer is and run the transfer. */ WRITE4(sc, RTSX_HDBAR, sc->rtsx_data_buffer); WRITE4(sc, RTSX_HDBCTLR, RTSX_TRIG_DMA | (read ? RTSX_DMA_READ : 0) | (cmd->data->len & 0x00ffffff)); } /* * Finish dma data transfer. * This Function is called by the interrupt handler via sc->rtsx_intr_trans_ok. */ static void rtsx_xfer_finish(struct rtsx_softc *sc) { struct mmc_command *cmd; int read; cmd = sc->rtsx_req->cmd; if (sc->rtsx_debug_mask & RTSX_TRACE_SD_CMD) device_printf(sc->rtsx_dev, "rtsx_xfer_finish() - CMD%d\n", cmd->opcode); read = ISSET(cmd->data->flags, MMC_DATA_READ); /* Sync data DMA buffer. */ bus_dmamap_sync(sc->rtsx_data_dma_tag, sc->rtsx_data_dmamap, BUS_DMASYNC_POSTREAD); bus_dmamap_sync(sc->rtsx_data_dma_tag, sc->rtsx_data_dmamap, BUS_DMASYNC_POSTWRITE); if (read) { memcpy(cmd->data->data, sc->rtsx_data_dmamem, cmd->data->len); rtsx_req_done(sc); } else { /* Send CMD12 after AUTO_WRITE3 (see mmcsd_rw() in mmcsd.c) */ /* and complete request. */ sc->rtsx_intr_trans_ok = NULL; rtsx_send_req(sc, sc->rtsx_req->stop); } } /* * Manage request timeout. */ static void rtsx_timeout(void *arg) { struct rtsx_softc *sc; sc = (struct rtsx_softc *)arg; if (sc->rtsx_req != NULL) { device_printf(sc->rtsx_dev, "Controller timeout for CMD%u\n", sc->rtsx_req->cmd->opcode); sc->rtsx_req->cmd->error = MMC_ERR_TIMEOUT; rtsx_stop_cmd(sc); rtsx_req_done(sc); } else { device_printf(sc->rtsx_dev, "Controller timeout!\n"); } } #ifdef MMCCAM static int rtsx_get_tran_settings(device_t dev, struct ccb_trans_settings_mmc *cts) { struct rtsx_softc *sc; sc = device_get_softc(dev); cts->host_ocr = sc->rtsx_host.host_ocr; cts->host_f_min = sc->rtsx_host.f_min; cts->host_f_max = sc->rtsx_host.f_max; cts->host_caps = sc->rtsx_host.caps; cts->host_max_data = RTSX_DMA_DATA_BUFSIZE / MMC_SECTOR_SIZE; memcpy(&cts->ios, &sc->rtsx_host.ios, sizeof(struct mmc_ios)); return (0); } /* * Apply settings and return status accordingly. */ static int rtsx_set_tran_settings(device_t dev, struct ccb_trans_settings_mmc *cts) { struct rtsx_softc *sc; struct mmc_ios *ios; struct mmc_ios *new_ios; sc = device_get_softc(dev); ios = &sc->rtsx_host.ios; new_ios = &cts->ios; /* Update only requested fields */ if (cts->ios_valid & MMC_CLK) { ios->clock = new_ios->clock; sc->rtsx_ios_clock = -1; /* To be updated by rtsx_mmcbr_update_ios(). */ if (sc->rtsx_debug_mask & RTSX_DEBUG_BASIC) device_printf(sc->rtsx_dev, "rtsx_set_tran_settings() - clock: %u\n", ios->clock); } if (cts->ios_valid & MMC_VDD) { ios->vdd = new_ios->vdd; if (sc->rtsx_debug_mask & RTSX_DEBUG_BASIC) device_printf(sc->rtsx_dev, "rtsx_set_tran_settings() - vdd: %d\n", ios->vdd); } if (cts->ios_valid & MMC_CS) { ios->chip_select = new_ios->chip_select; if (sc->rtsx_debug_mask & RTSX_DEBUG_BASIC) device_printf(sc->rtsx_dev, "rtsx_set_tran_settings() - chip_select: %d\n", ios->chip_select); } if (cts->ios_valid & MMC_BW) { ios->bus_width = new_ios->bus_width; sc->rtsx_ios_bus_width = -1; /* To be updated by rtsx_mmcbr_update_ios(). */ if (sc->rtsx_debug_mask & RTSX_DEBUG_BASIC) device_printf(sc->rtsx_dev, "rtsx_set_tran_settings() - bus width: %d\n", ios->bus_width); } if (cts->ios_valid & MMC_PM) { ios->power_mode = new_ios->power_mode; sc->rtsx_ios_power_mode = -1; /* To be updated by rtsx_mmcbr_update_ios(). */ if (sc->rtsx_debug_mask & RTSX_DEBUG_BASIC) device_printf(sc->rtsx_dev, "rtsx_set_tran_settings() - power mode: %d\n", ios->power_mode); } if (cts->ios_valid & MMC_BT) { ios->timing = new_ios->timing; sc->rtsx_ios_timing = -1; /* To be updated by rtsx_mmcbr_update_ios(). */ if (sc->rtsx_debug_mask & RTSX_DEBUG_BASIC) device_printf(sc->rtsx_dev, "rtsx_set_tran_settings() - timing: %d\n", ios->timing); } if (cts->ios_valid & MMC_BM) { ios->bus_mode = new_ios->bus_mode; if (sc->rtsx_debug_mask & RTSX_DEBUG_BASIC) device_printf(sc->rtsx_dev, "rtsx_set_tran_settings() - bus mode: %d\n", ios->bus_mode); } #if __FreeBSD_version >= 1300000 if (cts->ios_valid & MMC_VCCQ) { ios->vccq = new_ios->vccq; sc->rtsx_ios_vccq = -1; /* To be updated by rtsx_mmcbr_update_ios(). */ if (sc->rtsx_debug_mask & RTSX_DEBUG_BASIC) device_printf(sc->rtsx_dev, "rtsx_set_tran_settings() - vccq: %d\n", ios->vccq); } #endif /* __FreeBSD_version >= 1300000 */ if (rtsx_mmcbr_update_ios(sc->rtsx_dev, NULL) == 0) return (CAM_REQ_CMP); else return (CAM_REQ_CMP_ERR); } /* * Build a request and run it. */ static int rtsx_cam_request(device_t dev, union ccb *ccb) { struct rtsx_softc *sc; sc = device_get_softc(dev); RTSX_LOCK(sc); if (sc->rtsx_ccb != NULL) { RTSX_UNLOCK(sc); return (CAM_BUSY); } sc->rtsx_ccb = ccb; sc->rtsx_cam_req.cmd = &ccb->mmcio.cmd; sc->rtsx_cam_req.stop = &ccb->mmcio.stop; RTSX_UNLOCK(sc); rtsx_mmcbr_request(sc->rtsx_dev, NULL, &sc->rtsx_cam_req); return (0); } #endif /* MMCCAM */ static int rtsx_read_ivar(device_t bus, device_t child, int which, uintptr_t *result) { struct rtsx_softc *sc; sc = device_get_softc(bus); switch (which) { case MMCBR_IVAR_BUS_MODE: /* ivar 0 - 1 = opendrain, 2 = pushpull */ *result = sc->rtsx_host.ios.bus_mode; break; case MMCBR_IVAR_BUS_WIDTH: /* ivar 1 - 0 = 1b 2 = 4b, 3 = 8b */ *result = sc->rtsx_host.ios.bus_width; break; case MMCBR_IVAR_CHIP_SELECT: /* ivar 2 - O = dontcare, 1 = cs_high, 2 = cs_low */ *result = sc->rtsx_host.ios.chip_select; break; case MMCBR_IVAR_CLOCK: /* ivar 3 - clock in Hz */ *result = sc->rtsx_host.ios.clock; break; case MMCBR_IVAR_F_MIN: /* ivar 4 */ *result = sc->rtsx_host.f_min; break; case MMCBR_IVAR_F_MAX: /* ivar 5 */ *result = sc->rtsx_host.f_max; break; case MMCBR_IVAR_HOST_OCR: /* ivar 6 - host operation conditions register */ *result = sc->rtsx_host.host_ocr; break; case MMCBR_IVAR_MODE: /* ivar 7 - 0 = mode_mmc, 1 = mode_sd */ *result = sc->rtsx_host.mode; break; case MMCBR_IVAR_OCR: /* ivar 8 - operation conditions register */ *result = sc->rtsx_host.ocr; break; case MMCBR_IVAR_POWER_MODE: /* ivar 9 - 0 = off, 1 = up, 2 = on */ *result = sc->rtsx_host.ios.power_mode; break; case MMCBR_IVAR_VDD: /* ivar 11 - voltage power pin */ *result = sc->rtsx_host.ios.vdd; break; case MMCBR_IVAR_VCCQ: /* ivar 12 - signaling: 0 = 1.20V, 1 = 1.80V, 2 = 3.30V */ *result = sc->rtsx_host.ios.vccq; break; case MMCBR_IVAR_CAPS: /* ivar 13 */ *result = sc->rtsx_host.caps; break; case MMCBR_IVAR_TIMING: /* ivar 14 - 0 = normal, 1 = timing_hs, ... */ *result = sc->rtsx_host.ios.timing; break; case MMCBR_IVAR_MAX_DATA: /* ivar 15 */ *result = RTSX_DMA_DATA_BUFSIZE / MMC_SECTOR_SIZE; break; case MMCBR_IVAR_RETUNE_REQ: /* ivar 10 */ case MMCBR_IVAR_MAX_BUSY_TIMEOUT: /* ivar 16 */ default: return (EINVAL); } if (sc->rtsx_debug_mask & RTSX_TRACE_SD_CMD) device_printf(bus, "Read ivar #%d, value %#x / #%d\n", which, *(int *)result, *(int *)result); return (0); } static int rtsx_write_ivar(device_t bus, device_t child, int which, uintptr_t value) { struct rtsx_softc *sc; sc = device_get_softc(bus); if (sc->rtsx_debug_mask & RTSX_TRACE_SD_CMD) device_printf(bus, "Write ivar #%d, value %#x / #%d\n", which, (int)value, (int)value); switch (which) { case MMCBR_IVAR_BUS_MODE: /* ivar 0 - 1 = opendrain, 2 = pushpull */ sc->rtsx_host.ios.bus_mode = value; break; case MMCBR_IVAR_BUS_WIDTH: /* ivar 1 - 0 = 1b 2 = 4b, 3 = 8b */ sc->rtsx_host.ios.bus_width = value; sc->rtsx_ios_bus_width = -1; /* To be updated on next rtsx_mmcbr_update_ios(). */ break; case MMCBR_IVAR_CHIP_SELECT: /* ivar 2 - O = dontcare, 1 = cs_high, 2 = cs_low */ sc->rtsx_host.ios.chip_select = value; break; case MMCBR_IVAR_CLOCK: /* ivar 3 - clock in Hz */ sc->rtsx_host.ios.clock = value; sc->rtsx_ios_clock = -1; /* To be updated on next rtsx_mmcbr_update_ios(). */ break; case MMCBR_IVAR_MODE: /* ivar 7 - 0 = mode_mmc, 1 = mode_sd */ sc->rtsx_host.mode = value; break; case MMCBR_IVAR_OCR: /* ivar 8 - operation conditions register */ sc->rtsx_host.ocr = value; break; case MMCBR_IVAR_POWER_MODE: /* ivar 9 - 0 = off, 1 = up, 2 = on */ sc->rtsx_host.ios.power_mode = value; sc->rtsx_ios_power_mode = -1; /* To be updated on next rtsx_mmcbr_update_ios(). */ break; case MMCBR_IVAR_VDD: /* ivar 11 - voltage power pin */ sc->rtsx_host.ios.vdd = value; break; case MMCBR_IVAR_VCCQ: /* ivar 12 - signaling: 0 = 1.20V, 1 = 1.80V, 2 = 3.30V */ sc->rtsx_host.ios.vccq = value; sc->rtsx_ios_vccq = value; /* rtsx_mmcbr_switch_vccq() will be called by mmc.c (MMCCAM undef). */ break; case MMCBR_IVAR_TIMING: /* ivar 14 - 0 = normal, 1 = timing_hs, ... */ sc->rtsx_host.ios.timing = value; sc->rtsx_ios_timing = -1; /* To be updated on next rtsx_mmcbr_update_ios(). */ break; /* These are read-only. */ case MMCBR_IVAR_F_MIN: /* ivar 4 */ case MMCBR_IVAR_F_MAX: /* ivar 5 */ case MMCBR_IVAR_HOST_OCR: /* ivar 6 - host operation conditions register */ case MMCBR_IVAR_RETUNE_REQ: /* ivar 10 */ case MMCBR_IVAR_CAPS: /* ivar 13 */ case MMCBR_IVAR_MAX_DATA: /* ivar 15 */ case MMCBR_IVAR_MAX_BUSY_TIMEOUT: /* ivar 16 */ default: return (EINVAL); } return (0); } static int rtsx_mmcbr_update_ios(device_t bus, device_t child__unused) { struct rtsx_softc *sc; struct mmc_ios *ios; int error; sc = device_get_softc(bus); ios = &sc->rtsx_host.ios; if (sc->rtsx_debug_mask & RTSX_TRACE_SD_CMD) device_printf(bus, "rtsx_mmcbr_update_ios()\n"); /* if MMCBR_IVAR_BUS_WIDTH updated. */ if (sc->rtsx_ios_bus_width < 0) { sc->rtsx_ios_bus_width = ios->bus_width; if ((error = rtsx_set_bus_width(sc, ios->bus_width))) return (error); } /* if MMCBR_IVAR_POWER_MODE updated. */ if (sc->rtsx_ios_power_mode < 0) { sc->rtsx_ios_power_mode = ios->power_mode; switch (ios->power_mode) { case power_off: if ((error = rtsx_bus_power_off(sc))) return (error); break; case power_up: if ((error = rtsx_bus_power_on(sc))) return (error); break; case power_on: if ((error = rtsx_bus_power_on(sc))) return (error); break; } } sc->rtsx_double_clk = true; sc->rtsx_vpclk = false; /* if MMCBR_IVAR_TIMING updated. */ if (sc->rtsx_ios_timing < 0) { sc->rtsx_ios_timing = ios->timing; if ((error = rtsx_set_sd_timing(sc, ios->timing))) return (error); } /* if MMCBR_IVAR_CLOCK updated, must be after rtsx_set_sd_timing() */ if (sc->rtsx_ios_clock < 0) { sc->rtsx_ios_clock = ios->clock; if ((error = rtsx_set_sd_clock(sc, ios->clock))) return (error); } /* if MMCCAM and vccq updated */ if (sc->rtsx_ios_vccq < 0) { sc->rtsx_ios_vccq = ios->vccq; if ((error = rtsx_mmcbr_switch_vccq(sc->rtsx_dev, NULL))) return (error); } return (0); } /* * Set output stage logic power voltage. */ static int rtsx_mmcbr_switch_vccq(device_t bus, device_t child __unused) { struct rtsx_softc *sc; int vccq = 0; int error; sc = device_get_softc(bus); switch (sc->rtsx_host.ios.vccq) { case vccq_120: vccq = 120; break; case vccq_180: vccq = 180; break; case vccq_330: vccq = 330; break; }; /* It seems it is always vccq_330. */ if (vccq == 330) { switch (sc->rtsx_device_id) { uint16_t val; case RTSX_RTS5227: if ((error = rtsx_write_phy(sc, 0x08, 0x4FE4))) return (error); if ((error = rtsx_rts5227_fill_driving(sc))) return (error); break; case RTSX_RTS5209: case RTSX_RTS5229: RTSX_BITOP(sc, RTSX_SD30_CMD_DRIVE_SEL, RTSX_SD30_DRIVE_SEL_MASK, sc->rtsx_sd30_drive_sel_3v3); if ((error = rtsx_write_phy(sc, 0x08, 0x4FE4))) return (error); break; case RTSX_RTS522A: if ((error = rtsx_write_phy(sc, 0x08, 0x57E4))) return (error); if ((error = rtsx_rts5227_fill_driving(sc))) return (error); break; case RTSX_RTS525A: RTSX_BITOP(sc, RTSX_LDO_CONFIG2, RTSX_LDO_D3318_MASK, RTSX_LDO_D3318_33V); RTSX_BITOP(sc, RTSX_SD_PAD_CTL, RTSX_SD_IO_USING_1V8, 0); if ((error = rtsx_rts5249_fill_driving(sc))) return (error); break; case RTSX_RTS5249: if ((error = rtsx_read_phy(sc, RTSX_PHY_TUNE, &val))) return (error); if ((error = rtsx_write_phy(sc, RTSX_PHY_TUNE, (val & RTSX_PHY_TUNE_VOLTAGE_MASK) | RTSX_PHY_TUNE_VOLTAGE_3V3))) return (error); if ((error = rtsx_rts5249_fill_driving(sc))) return (error); break; case RTSX_RTS5260: RTSX_BITOP(sc, RTSX_LDO_CONFIG2, RTSX_DV331812_VDD1, RTSX_DV331812_VDD1); RTSX_BITOP(sc, RTSX_LDO_DV18_CFG, RTSX_DV331812_MASK, RTSX_DV331812_33); RTSX_CLR(sc, RTSX_SD_PAD_CTL, RTSX_SD_IO_USING_1V8); if ((error = rtsx_rts5260_fill_driving(sc))) return (error); break; case RTSX_RTL8402: RTSX_BITOP(sc, RTSX_SD30_CMD_DRIVE_SEL, RTSX_SD30_DRIVE_SEL_MASK, sc->rtsx_sd30_drive_sel_3v3); RTSX_BITOP(sc, RTSX_LDO_CTL, (RTSX_BPP_ASIC_MASK << RTSX_BPP_SHIFT_8402) | RTSX_BPP_PAD_MASK, (RTSX_BPP_ASIC_3V3 << RTSX_BPP_SHIFT_8402) | RTSX_BPP_PAD_3V3); break; case RTSX_RTL8411: case RTSX_RTL8411B: RTSX_BITOP(sc, RTSX_SD30_CMD_DRIVE_SEL, RTSX_SD30_DRIVE_SEL_MASK, sc->rtsx_sd30_drive_sel_3v3); RTSX_BITOP(sc, RTSX_LDO_CTL, (RTSX_BPP_ASIC_MASK << RTSX_BPP_SHIFT_8411) | RTSX_BPP_PAD_MASK, (RTSX_BPP_ASIC_3V3 << RTSX_BPP_SHIFT_8411) | RTSX_BPP_PAD_3V3); break; } DELAY(300); } if (sc->rtsx_debug_mask & (RTSX_DEBUG_BASIC | RTSX_TRACE_SD_CMD)) device_printf(sc->rtsx_dev, "rtsx_mmcbr_switch_vccq(%d)\n", vccq); return (0); } #ifndef MMCCAM /* * Tune card if bus_timing_uhs_sdr50. */ static int rtsx_mmcbr_tune(device_t bus, device_t child __unused, bool hs400) { struct rtsx_softc *sc; uint32_t raw_phase_map[RTSX_RX_TUNING_CNT] = {0}; uint32_t phase_map; uint8_t final_phase; int i; sc = device_get_softc(bus); if (sc->rtsx_debug_mask & RTSX_DEBUG_BASIC) device_printf(sc->rtsx_dev, "rtsx_mmcbr_tune() - hs400 is %s\n", (hs400) ? "true" : "false"); if (sc->rtsx_ios_timing != bus_timing_uhs_sdr50) return (0); sc->rtsx_tuning_mode = true; switch (sc->rtsx_device_id) { case RTSX_RTS5209: case RTSX_RTS5227: rtsx_sd_change_tx_phase(sc, 27); break; case RTSX_RTS522A: rtsx_sd_change_tx_phase(sc, 20); break; case RTSX_RTS5229: rtsx_sd_change_tx_phase(sc, 27); break; case RTSX_RTS525A: case RTSX_RTS5249: rtsx_sd_change_tx_phase(sc, 29); break; case RTSX_RTL8402: case RTSX_RTL8411: case RTSX_RTL8411B: rtsx_sd_change_tx_phase(sc, 7); break; } /* trying rx tuning for bus_timing_uhs_sdr50. */ for (i = 0; i < RTSX_RX_TUNING_CNT; i++) { rtsx_sd_tuning_rx_phase(sc, &(raw_phase_map[i])); if (raw_phase_map[i] == 0) break; } phase_map = 0xffffffff; for (i = 0; i < RTSX_RX_TUNING_CNT; i++) { if (sc->rtsx_debug_mask & (RTSX_DEBUG_BASIC | RTSX_DEBUG_TUNING)) device_printf(sc->rtsx_dev, "rtsx_mmcbr_tune() - RX raw_phase_map[%d]: 0x%08x\n", i, raw_phase_map[i]); phase_map &= raw_phase_map[i]; } if (sc->rtsx_debug_mask & RTSX_DEBUG_BASIC) device_printf(sc->rtsx_dev, "rtsx_mmcbr_tune() - RX phase_map: 0x%08x\n", phase_map); if (phase_map) { final_phase = rtsx_sd_search_final_rx_phase(sc, phase_map); if (final_phase != 0xff) { rtsx_sd_change_rx_phase(sc, final_phase); } } sc->rtsx_tuning_mode = false; return (0); } static int rtsx_mmcbr_retune(device_t bus, device_t child __unused, bool reset __unused) { struct rtsx_softc *sc; sc = device_get_softc(bus); if (sc->rtsx_debug_mask & RTSX_TRACE_SD_CMD) device_printf(sc->rtsx_dev, "rtsx_mmcbr_retune()\n"); return (0); } #endif /* !MMCCAM */ static int rtsx_mmcbr_request(device_t bus, device_t child __unused, struct mmc_request *req) { struct rtsx_softc *sc; struct mmc_command *cmd; int timeout; int error; sc = device_get_softc(bus); RTSX_LOCK(sc); if (sc->rtsx_req != NULL) { RTSX_UNLOCK(sc); return (EBUSY); } sc->rtsx_req = req; cmd = req->cmd; cmd->error = error = MMC_ERR_NONE; sc->rtsx_intr_status = 0; sc->rtsx_intr_trans_ok = NULL; sc->rtsx_intr_trans_ko = rtsx_req_done; if (sc->rtsx_debug_mask & RTSX_TRACE_SD_CMD) device_printf(sc->rtsx_dev, "rtsx_mmcbr_request(CMD%u arg %#x, flags %#x, dlen %u, dflags %#x)\n", cmd->opcode, cmd->arg, cmd->flags, cmd->data != NULL ? (unsigned int)cmd->data->len : 0, cmd->data != NULL ? cmd->data->flags : 0); /* Check if card present. */ if (!ISSET(sc->rtsx_flags, RTSX_F_CARD_PRESENT)) { cmd->error = error = MMC_ERR_FAILED; goto end; } /* Refuse SDIO probe if the chip doesn't support SDIO. */ if (cmd->opcode == IO_SEND_OP_COND && !ISSET(sc->rtsx_flags, RTSX_F_SDIO_SUPPORT)) { cmd->error = error = MMC_ERR_INVALID; goto end; } /* Return MMC_ERR_TIMEOUT for SD_IO_RW_DIRECT and IO_SEND_OP_COND. */ if (cmd->opcode == SD_IO_RW_DIRECT || cmd->opcode == IO_SEND_OP_COND) { cmd->error = error = MMC_ERR_TIMEOUT; goto end; } /* Select SD card. */ RTSX_BITOP(sc, RTSX_CARD_SELECT, 0x07, RTSX_SD_MOD_SEL); RTSX_BITOP(sc, RTSX_CARD_SHARE_MODE, RTSX_CARD_SHARE_MASK, RTSX_CARD_SHARE_48_SD); if (cmd->data == NULL) { DELAY(200); timeout = sc->rtsx_timeout_cmd; error = rtsx_send_req(sc, cmd); } else if (cmd->data->len <= 512) { timeout = sc->rtsx_timeout_io; error = rtsx_xfer_short(sc, cmd); } else { timeout = sc->rtsx_timeout_io; error = rtsx_xfer(sc, cmd); } end: if (error == MMC_ERR_NONE) { callout_reset(&sc->rtsx_timeout_callout, timeout * hz, rtsx_timeout, sc); } else { rtsx_req_done(sc); } RTSX_UNLOCK(sc); return (error); } #ifndef MMCCAM static int rtsx_mmcbr_get_ro(device_t bus, device_t child __unused) { struct rtsx_softc *sc; sc = device_get_softc(bus); if (sc->rtsx_inversion == 0) return (sc->rtsx_read_only); else return !(sc->rtsx_read_only); } static int rtsx_mmcbr_acquire_host(device_t bus, device_t child __unused) { struct rtsx_softc *sc; sc = device_get_softc(bus); if (sc->rtsx_debug_mask & RTSX_TRACE_SD_CMD) device_printf(bus, "rtsx_mmcbr_acquire_host()\n"); RTSX_LOCK(sc); while (sc->rtsx_bus_busy) msleep(&sc->rtsx_bus_busy, &sc->rtsx_mtx, 0, "rtsxah", 0); sc->rtsx_bus_busy++; RTSX_UNLOCK(sc); return (0); } static int rtsx_mmcbr_release_host(device_t bus, device_t child __unused) { struct rtsx_softc *sc; sc = device_get_softc(bus); if (sc->rtsx_debug_mask & RTSX_TRACE_SD_CMD) device_printf(bus, "rtsx_mmcbr_release_host()\n"); RTSX_LOCK(sc); sc->rtsx_bus_busy--; wakeup(&sc->rtsx_bus_busy); RTSX_UNLOCK(sc); return (0); } #endif /* !MMCCAM */ /* * * PCI Support Functions * */ /* * Compare the device ID (chip) of this device against the IDs that this driver * supports. If there is a match, set the description and return success. */ static int rtsx_probe(device_t dev) { uint16_t vendor_id; uint16_t device_id; int i; int result; vendor_id = pci_get_vendor(dev); device_id = pci_get_device(dev); result = ENXIO; for (i = 0; rtsx_devices[i].vendor_id != 0; i++) { if (rtsx_devices[i].vendor_id == vendor_id && rtsx_devices[i].device_id == device_id) { device_set_desc(dev, rtsx_devices[i].desc); result = BUS_PROBE_DEFAULT; break; } } return (result); } /* * Attach function is only called if the probe is successful. */ static int rtsx_attach(device_t dev) { struct rtsx_softc *sc = device_get_softc(dev); uint16_t vendor_id; uint16_t device_id; struct sysctl_ctx_list *ctx; struct sysctl_oid_list *tree; int msi_count = 1; uint32_t sdio_cfg; int error; char *maker; char *family; char *product; int i; vendor_id = pci_get_vendor(dev); device_id = pci_get_device(dev); if (bootverbose) device_printf(dev, "Attach - Vendor ID: 0x%x - Device ID: 0x%x\n", vendor_id, device_id); sc->rtsx_dev = dev; sc->rtsx_device_id = device_id; sc->rtsx_req = NULL; sc->rtsx_timeout_cmd = 1; sc->rtsx_timeout_io = 10; sc->rtsx_read_only = 0; sc->rtsx_inversion = 0; sc->rtsx_force_timing = 0; sc->rtsx_debug_mask = 0; sc->rtsx_read_count = 0; sc->rtsx_write_count = 0; maker = kern_getenv("smbios.system.maker"); family = kern_getenv("smbios.system.family"); product = kern_getenv("smbios.system.product"); for (i = 0; rtsx_inversion_models[i].maker != NULL; i++) { if (strcmp(rtsx_inversion_models[i].maker, maker) == 0 && strcmp(rtsx_inversion_models[i].family, family) == 0 && strcmp(rtsx_inversion_models[i].product, product) == 0) { device_printf(dev, "Inversion activated for %s/%s/%s, see BUG in rtsx(4)\n", maker, family, product); device_printf(dev, "If a card is detected without an SD card present," " add dev.rtsx.0.inversion=0 in loader.conf(5)\n"); sc->rtsx_inversion = 1; } } RTSX_LOCK_INIT(sc); ctx = device_get_sysctl_ctx(dev); tree = SYSCTL_CHILDREN(device_get_sysctl_tree(dev)); SYSCTL_ADD_INT(ctx, tree, OID_AUTO, "timeout_io", CTLFLAG_RW, &sc->rtsx_timeout_io, 0, "Request timeout for I/O commands in seconds"); SYSCTL_ADD_INT(ctx, tree, OID_AUTO, "timeout_cmd", CTLFLAG_RW, &sc->rtsx_timeout_cmd, 0, "Request timeout for setup commands in seconds"); SYSCTL_ADD_U8(ctx, tree, OID_AUTO, "read_only", CTLFLAG_RD, &sc->rtsx_read_only, 0, "Card is write protected"); SYSCTL_ADD_U8(ctx, tree, OID_AUTO, "inversion", CTLFLAG_RWTUN, &sc->rtsx_inversion, 0, "Inversion of card detection and read only status"); SYSCTL_ADD_U8(ctx, tree, OID_AUTO, "force_timing", CTLFLAG_RW, &sc->rtsx_force_timing, 0, "Force bus_timing_uhs_sdr50"); SYSCTL_ADD_U8(ctx, tree, OID_AUTO, "debug_mask", CTLFLAG_RWTUN, &sc->rtsx_debug_mask, 0, "debugging mask, see rtsx(4)"); SYSCTL_ADD_U64(ctx, tree, OID_AUTO, "read_count", CTLFLAG_RD | CTLFLAG_STATS, &sc->rtsx_read_count, 0, "Count of read operations"); SYSCTL_ADD_U64(ctx, tree, OID_AUTO, "write_count", CTLFLAG_RD | CTLFLAG_STATS, &sc->rtsx_write_count, 0, "Count of write operations"); if (bootverbose || sc->rtsx_debug_mask & RTSX_DEBUG_BASIC) device_printf(dev, "We are running with inversion: %d\n", sc->rtsx_inversion); /* Allocate IRQ. */ sc->rtsx_irq_res_id = 0; if (pci_alloc_msi(dev, &msi_count) == 0) sc->rtsx_irq_res_id = 1; sc->rtsx_irq_res = bus_alloc_resource_any(dev, SYS_RES_IRQ, &sc->rtsx_irq_res_id, RF_ACTIVE | (sc->rtsx_irq_res_id != 0 ? 0 : RF_SHAREABLE)); if (sc->rtsx_irq_res == NULL) { device_printf(dev, "Can't allocate IRQ resources for %d\n", sc->rtsx_irq_res_id); pci_release_msi(dev); return (ENXIO); } callout_init_mtx(&sc->rtsx_timeout_callout, &sc->rtsx_mtx, 0); /* Allocate memory resource. */ if (sc->rtsx_device_id == RTSX_RTS525A) sc->rtsx_mem_res_id = PCIR_BAR(1); else sc->rtsx_mem_res_id = PCIR_BAR(0); sc->rtsx_mem_res = bus_alloc_resource_any(dev, SYS_RES_MEMORY, &sc->rtsx_mem_res_id, RF_ACTIVE); if (sc->rtsx_mem_res == NULL) { device_printf(dev, "Can't allocate memory resource for %d\n", sc->rtsx_mem_res_id); goto destroy_rtsx_irq_res; } if (bootverbose) device_printf(dev, "rtsx_irq_res_id: %d, rtsx_mem_res_id: %d\n", sc->rtsx_irq_res_id, sc->rtsx_mem_res_id); sc->rtsx_mem_btag = rman_get_bustag(sc->rtsx_mem_res); sc->rtsx_mem_bhandle = rman_get_bushandle(sc->rtsx_mem_res); TIMEOUT_TASK_INIT(taskqueue_swi_giant, &sc->rtsx_card_insert_task, 0, rtsx_card_task, sc); TASK_INIT(&sc->rtsx_card_remove_task, 0, rtsx_card_task, sc); /* Allocate two DMA buffers: a command buffer and a data buffer. */ error = rtsx_dma_alloc(sc); if (error) goto destroy_rtsx_irq_res; /* Activate the interrupt. */ error = bus_setup_intr(dev, sc->rtsx_irq_res, INTR_TYPE_MISC | INTR_MPSAFE, NULL, rtsx_intr, sc, &sc->rtsx_irq_cookie); if (error) { device_printf(dev, "Can't set up irq [0x%x]!\n", error); goto destroy_rtsx_mem_res; } pci_enable_busmaster(dev); if (rtsx_read_cfg(sc, 0, RTSX_SDIOCFG_REG, &sdio_cfg) == 0) { if ((sdio_cfg & RTSX_SDIOCFG_SDIO_ONLY) || (sdio_cfg & RTSX_SDIOCFG_HAVE_SDIO)) sc->rtsx_flags |= RTSX_F_SDIO_SUPPORT; } #ifdef MMCCAM sc->rtsx_ccb = NULL; sc->rtsx_cam_status = 0; SYSCTL_ADD_U8(ctx, tree, OID_AUTO, "cam_status", CTLFLAG_RD, &sc->rtsx_cam_status, 0, "driver cam card present"); if (mmc_cam_sim_alloc(dev, "rtsx_mmc", &sc->rtsx_mmc_sim) != 0) { device_printf(dev, "Can't allocate CAM SIM\n"); goto destroy_rtsx_irq; } #endif /* MMCCAM */ /* Initialize device. */ error = rtsx_init(sc); if (error) { device_printf(dev, "Error %d during rtsx_init()\n", error); goto destroy_rtsx_irq; } /* * Schedule a card detection as we won't get an interrupt * if the card is inserted when we attach. We wait a quarter * of a second to allow for a "spontaneous" interrupt which may * change the card presence state. This delay avoid a panic * on some configuration (e.g. Lenovo T540p). */ DELAY(250000); if (rtsx_is_card_present(sc)) device_printf(sc->rtsx_dev, "A card is detected\n"); else device_printf(sc->rtsx_dev, "No card is detected\n"); rtsx_card_task(sc, 0); if (bootverbose) device_printf(dev, "Device attached\n"); return (0); destroy_rtsx_irq: bus_teardown_intr(dev, sc->rtsx_irq_res, sc->rtsx_irq_cookie); destroy_rtsx_mem_res: bus_release_resource(dev, SYS_RES_MEMORY, sc->rtsx_mem_res_id, sc->rtsx_mem_res); rtsx_dma_free(sc); destroy_rtsx_irq_res: callout_drain(&sc->rtsx_timeout_callout); bus_release_resource(dev, SYS_RES_IRQ, sc->rtsx_irq_res_id, sc->rtsx_irq_res); pci_release_msi(dev); RTSX_LOCK_DESTROY(sc); return (ENXIO); } static int rtsx_detach(device_t dev) { struct rtsx_softc *sc = device_get_softc(dev); int error; if (bootverbose) device_printf(dev, "Detach - Vendor ID: 0x%x - Device ID: 0x%x\n", pci_get_vendor(dev), sc->rtsx_device_id); /* Disable interrupts. */ sc->rtsx_intr_enabled = 0; WRITE4(sc, RTSX_BIER, sc->rtsx_intr_enabled); /* Stop device. */ error = device_delete_children(sc->rtsx_dev); sc->rtsx_mmc_dev = NULL; if (error) return (error); taskqueue_drain_timeout(taskqueue_swi_giant, &sc->rtsx_card_insert_task); taskqueue_drain(taskqueue_swi_giant, &sc->rtsx_card_remove_task); /* Teardown the state in our softc created in our attach routine. */ rtsx_dma_free(sc); if (sc->rtsx_mem_res != NULL) bus_release_resource(dev, SYS_RES_MEMORY, sc->rtsx_mem_res_id, sc->rtsx_mem_res); if (sc->rtsx_irq_cookie != NULL) bus_teardown_intr(dev, sc->rtsx_irq_res, sc->rtsx_irq_cookie); if (sc->rtsx_irq_res != NULL) { callout_drain(&sc->rtsx_timeout_callout); bus_release_resource(dev, SYS_RES_IRQ, sc->rtsx_irq_res_id, sc->rtsx_irq_res); pci_release_msi(dev); } RTSX_LOCK_DESTROY(sc); #ifdef MMCCAM mmc_cam_sim_free(&sc->rtsx_mmc_sim); #endif /* MMCCAM */ return (0); } static int rtsx_shutdown(device_t dev) { if (bootverbose) device_printf(dev, "Shutdown\n"); return (0); } /* * Device suspend routine. */ static int rtsx_suspend(device_t dev) { struct rtsx_softc *sc = device_get_softc(dev); device_printf(dev, "Suspend\n"); #ifdef MMCCAM if (sc->rtsx_ccb != NULL) { device_printf(dev, "Request in progress: CMD%u, rtsr_intr_status: 0x%08x\n", sc->rtsx_ccb->mmcio.cmd.opcode, sc->rtsx_intr_status); } #else /* !MMCCAM */ if (sc->rtsx_req != NULL) { device_printf(dev, "Request in progress: CMD%u, rtsr_intr_status: 0x%08x\n", sc->rtsx_req->cmd->opcode, sc->rtsx_intr_status); } #endif /* MMCCAM */ bus_generic_suspend(dev); return (0); } /* * Device resume routine. */ static int rtsx_resume(device_t dev) { device_printf(dev, "Resume\n"); rtsx_init(device_get_softc(dev)); bus_generic_resume(dev); return (0); } static device_method_t rtsx_methods[] = { /* Device interface */ DEVMETHOD(device_probe, rtsx_probe), DEVMETHOD(device_attach, rtsx_attach), DEVMETHOD(device_detach, rtsx_detach), DEVMETHOD(device_shutdown, rtsx_shutdown), DEVMETHOD(device_suspend, rtsx_suspend), DEVMETHOD(device_resume, rtsx_resume), /* Bus interface */ DEVMETHOD(bus_read_ivar, rtsx_read_ivar), DEVMETHOD(bus_write_ivar, rtsx_write_ivar), #ifndef MMCCAM /* MMC bridge interface */ DEVMETHOD(mmcbr_update_ios, rtsx_mmcbr_update_ios), DEVMETHOD(mmcbr_switch_vccq, rtsx_mmcbr_switch_vccq), DEVMETHOD(mmcbr_tune, rtsx_mmcbr_tune), DEVMETHOD(mmcbr_retune, rtsx_mmcbr_retune), DEVMETHOD(mmcbr_request, rtsx_mmcbr_request), DEVMETHOD(mmcbr_get_ro, rtsx_mmcbr_get_ro), DEVMETHOD(mmcbr_acquire_host, rtsx_mmcbr_acquire_host), DEVMETHOD(mmcbr_release_host, rtsx_mmcbr_release_host), #endif /* !MMCCAM */ #ifdef MMCCAM /* MMCCAM interface */ DEVMETHOD(mmc_sim_get_tran_settings, rtsx_get_tran_settings), DEVMETHOD(mmc_sim_set_tran_settings, rtsx_set_tran_settings), DEVMETHOD(mmc_sim_cam_request, rtsx_cam_request), #endif /* MMCCAM */ DEVMETHOD_END }; DEFINE_CLASS_0(rtsx, rtsx_driver, rtsx_methods, sizeof(struct rtsx_softc)); DRIVER_MODULE(rtsx, pci, rtsx_driver, NULL, NULL); #ifndef MMCCAM MMC_DECLARE_BRIDGE(rtsx); #endif /* !MMCCAM */