/*- * SPDX-License-Identifier: BSD-2-Clause * * Copyright (c) 2009-2020 Alexander Motin * Copyright (c) 1997-2009 by Matthew Jacob * All rights reserved. * * Redistribution and use in source and binary forms, with or without * modification, are permitted provided that the following conditions * are met: * * 1. Redistributions of source code must retain the above copyright * notice, this list of conditions and the following disclaimer. * 2. Redistributions in binary form must reproduce the above copyright * notice, this list of conditions and the following disclaimer in the * documentation and/or other materials provided with the distribution. * * THIS SOFTWARE IS PROVIDED BY AUTHOR AND CONTRIBUTORS ``AS IS'' AND * ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE * ARE DISCLAIMED. IN NO EVENT SHALL AUTHOR OR CONTRIBUTORS BE LIABLE * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS * OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY * OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF * SUCH DAMAGE. * */ /* * Machine Independent (well, as best as possible) register * definitions for Qlogic ISP SCSI adapters. */ #ifndef _ISPREG_H #define _ISPREG_H /* * Hardware definitions for the Qlogic ISP registers. */ /* * This defines types of access to various registers. * * R: Read Only * W: Write Only * RW: Read/Write * * R*, W*, RW*: Read Only, Write Only, Read/Write, but only * if RISC processor in ISP is paused. */ /* * NB: The *_BLOCK definitions have no specific hardware meaning. * They serve simply to note to the MD layer which block of * registers offsets are being accessed. */ #define _NREG_BLKS 2 #define _BLK_REG_SHFT 7 #define _BLK_REG_MASK (1 << _BLK_REG_SHFT) #define BIU_BLOCK (0 << _BLK_REG_SHFT) #define MBOX_BLOCK (1 << _BLK_REG_SHFT) #define BIU_R2HST_INTR (1 << 15) /* RISC to Host Interrupt */ #define BIU_R2HST_PAUSED (1 << 8) /* RISC paused */ #define BIU_R2HST_ISTAT_MASK 0xff /* intr information && status */ #define ISPR2HST_ROM_MBX_OK 0x1 /* ROM mailbox cmd done ok */ #define ISPR2HST_ROM_MBX_FAIL 0x2 /* ROM mailbox cmd done fail */ #define ISPR2HST_MBX_OK 0x10 /* mailbox cmd done ok */ #define ISPR2HST_MBX_FAIL 0x11 /* mailbox cmd done fail */ #define ISPR2HST_ASYNC_EVENT 0x12 /* Async Event */ #define ISPR2HST_RSPQ_UPDATE 0x13 /* Response Queue Update */ #define ISPR2HST_RSPQ_UPDATE2 0x14 /* Response Queue Update */ #define ISPR2HST_RIO_16 0x15 /* RIO 1-16 */ #define ISPR2HST_FPOST 0x16 /* Low 16 bits fast post */ #define ISPR2HST_FPOST_CTIO 0x17 /* Low 16 bits fast post ctio */ #define ISPR2HST_ATIO_UPDATE 0x1C /* ATIO Queue Update */ #define ISPR2HST_ATIO_RSPQ_UPDATE 0x1D /* ATIO & Request Update */ #define ISPR2HST_ATIO_UPDATE2 0x1E /* ATIO Queue Update */ /* * 2400 Interface Offsets and Register Definitions * * The 2400 looks quite different in terms of registers from other QLogic cards. * It is getting to be a genuine pain and challenge to keep the same model * for all. */ #define BIU2400_FLASH_ADDR (BIU_BLOCK+0x00) /* Flash Access Address */ #define BIU2400_FLASH_DATA (BIU_BLOCK+0x04) /* Flash Data */ #define BIU2400_CSR (BIU_BLOCK+0x08) /* ISP Control/Status */ #define BIU2400_ICR (BIU_BLOCK+0x0C) /* ISP to PCI Interrupt Control */ #define BIU2400_ISR (BIU_BLOCK+0x10) /* ISP to PCI Interrupt Status */ #define BIU2400_REQINP (BIU_BLOCK+0x1C) /* Request Queue In */ #define BIU2400_REQOUTP (BIU_BLOCK+0x20) /* Request Queue Out */ #define BIU2400_RSPINP (BIU_BLOCK+0x24) /* Response Queue In */ #define BIU2400_RSPOUTP (BIU_BLOCK+0x28) /* Response Queue Out */ #define BIU2400_PRI_REQINP (BIU_BLOCK+0x2C) /* Priority Request Q In */ #define BIU2400_PRI_REQOUTP (BIU_BLOCK+0x30) /* Priority Request Q Out */ #define BIU2400_ATIO_RSPINP (BIU_BLOCK+0x3C) /* ATIO Queue In */ #define BIU2400_ATIO_RSPOUTP (BIU_BLOCK+0x40) /* ATIO Queue Out */ #define BIU2400_R2HSTS (BIU_BLOCK+0x44) /* RISC to Host Status */ #define BIU2400_HCCR (BIU_BLOCK+0x48) /* Host Command and Control Status */ #define BIU2400_GPIOD (BIU_BLOCK+0x4C) /* General Purpose I/O Data */ #define BIU2400_GPIOE (BIU_BLOCK+0x50) /* General Purpose I/O Enable */ #define BIU2400_IOBBA (BIU_BLOCK+0x54) /* I/O Bus Base Address */ #define BIU2400_HSEMA (BIU_BLOCK+0x58) /* Host-to-Host Semaphore */ /* BIU2400_FLASH_ADDR definitions */ #define BIU2400_FLASH_DFLAG (1 << 30) /* BIU2400_CSR definitions */ #define BIU2400_NVERR (1 << 18) #define BIU2400_DMA_ACTIVE (1 << 17) /* RO */ #define BIU2400_DMA_STOP (1 << 16) #define BIU2400_FUNCTION (1 << 15) /* RO */ #define BIU2400_PCIX_MODE(x) (((x) >> 8) & 0xf) /* RO */ #define BIU2400_CSR_64BIT (1 << 2) /* RO */ #define BIU2400_FLASH_ENABLE (1 << 1) #define BIU2400_SOFT_RESET (1 << 0) /* BIU2400_ICR definitions */ #define BIU2400_ICR_ENA_RISC_INT 0x8 #define BIU2400_IMASK (BIU2400_ICR_ENA_RISC_INT) /* BIU2400_ISR definitions */ #define BIU2400_ISR_RISC_INT 0x8 /* BIU2400_HCCR definitions */ #define HCCR_2400_CMD_NOP 0x00000000 #define HCCR_2400_CMD_RESET 0x10000000 #define HCCR_2400_CMD_CLEAR_RESET 0x20000000 #define HCCR_2400_CMD_PAUSE 0x30000000 #define HCCR_2400_CMD_RELEASE 0x40000000 #define HCCR_2400_CMD_SET_HOST_INT 0x50000000 #define HCCR_2400_CMD_CLEAR_HOST_INT 0x60000000 #define HCCR_2400_CMD_CLEAR_RISC_INT 0xA0000000 #define HCCR_2400_RISC_ERR(x) (((x) >> 12) & 0x7) /* RO */ #define HCCR_2400_RISC2HOST_INT (1 << 6) /* RO */ #define HCCR_2400_RISC_RESET (1 << 5) /* RO */ /* * Mailbox Block Register Offsets */ #define INMAILBOX0 (MBOX_BLOCK+0x0) #define INMAILBOX1 (MBOX_BLOCK+0x2) #define INMAILBOX2 (MBOX_BLOCK+0x4) #define INMAILBOX3 (MBOX_BLOCK+0x6) #define INMAILBOX4 (MBOX_BLOCK+0x8) #define INMAILBOX5 (MBOX_BLOCK+0xA) #define INMAILBOX6 (MBOX_BLOCK+0xC) #define INMAILBOX7 (MBOX_BLOCK+0xE) #define OUTMAILBOX0 (MBOX_BLOCK+0x0) #define OUTMAILBOX1 (MBOX_BLOCK+0x2) #define OUTMAILBOX2 (MBOX_BLOCK+0x4) #define OUTMAILBOX3 (MBOX_BLOCK+0x6) #define OUTMAILBOX4 (MBOX_BLOCK+0x8) #define OUTMAILBOX5 (MBOX_BLOCK+0xA) #define OUTMAILBOX6 (MBOX_BLOCK+0xC) #define OUTMAILBOX7 (MBOX_BLOCK+0xE) #define MBOX_OFF(n) (MBOX_BLOCK + ((n) << 1)) #define ISP_NMBOX(isp) 32 #define MAX_MAILBOX 32 /* if timeout == 0, then default timeout is picked */ #define MBCMD_DEFAULT_TIMEOUT 100000 /* 100 ms */ typedef struct { uint16_t param[MAX_MAILBOX]; uint32_t ibits; /* bits to add for register copyin */ uint32_t obits; /* bits to add for register copyout */ uint32_t ibitm; /* bits to mask for register copyin */ uint32_t obitm; /* bits to mask for register copyout */ uint32_t logval; /* Bitmask of status codes to log */ uint32_t timeout; uint32_t lineno; const char *func; } mbreg_t; #define MBSINIT(mbxp, code, loglev, timo) \ ISP_MEMZERO((mbxp), sizeof (mbreg_t)); \ (mbxp)->ibitm = ~0; \ (mbxp)->obitm = ~0; \ (mbxp)->param[0] = code; \ (mbxp)->lineno = __LINE__; \ (mbxp)->func = __func__; \ (mbxp)->logval = loglev; \ (mbxp)->timeout = timo /* * Defines for Interrupts */ #define ISP_INTS_ENABLED(isp) \ (ISP_READ(isp, BIU2400_ICR) & BIU2400_IMASK) #define ISP_ENABLE_INTS(isp) \ ISP_WRITE(isp, BIU2400_ICR, BIU2400_IMASK) #define ISP_DISABLE_INTS(isp) \ ISP_WRITE(isp, BIU2400_ICR, 0) /* * NVRAM Definitions (PCI cards only) */ /* * Qlogic 2400 NVRAM is an array of 512 bytes with a 32 bit checksum. */ #define ISP2400_NVRAM_PORT_ADDR(c) (0x100 * (c) + 0x80) #define ISP2400_NVRAM_SIZE 512 #define ISP2400_NVRAM_VERSION(c) ((c)[4] | ((c)[5] << 8)) #define ISP2400_NVRAM_MAXFRAMELENGTH(c) (((c)[12]) | ((c)[13] << 8)) #define ISP2400_NVRAM_HARDLOOPID(c) ((c)[18] | ((c)[19] << 8)) #define ISP2400_NVRAM_PORT_NAME(c) (\ (((uint64_t)(c)[20]) << 56) | \ (((uint64_t)(c)[21]) << 48) | \ (((uint64_t)(c)[22]) << 40) | \ (((uint64_t)(c)[23]) << 32) | \ (((uint64_t)(c)[24]) << 24) | \ (((uint64_t)(c)[25]) << 16) | \ (((uint64_t)(c)[26]) << 8) | \ (((uint64_t)(c)[27]) << 0)) #define ISP2400_NVRAM_NODE_NAME(c) (\ (((uint64_t)(c)[28]) << 56) | \ (((uint64_t)(c)[29]) << 48) | \ (((uint64_t)(c)[30]) << 40) | \ (((uint64_t)(c)[31]) << 32) | \ (((uint64_t)(c)[32]) << 24) | \ (((uint64_t)(c)[33]) << 16) | \ (((uint64_t)(c)[34]) << 8) | \ (((uint64_t)(c)[35]) << 0)) #define ISP2400_NVRAM_LOGIN_RETRY_CNT(c) ((c)[36] | ((c)[37] << 8)) #define ISP2400_NVRAM_LINK_DOWN_ON_NOS(c) ((c)[38] | ((c)[39] << 8)) #define ISP2400_NVRAM_INTERRUPT_DELAY(c) ((c)[40] | ((c)[41] << 8)) #define ISP2400_NVRAM_LOGIN_TIMEOUT(c) ((c)[42] | ((c)[43] << 8)) #define ISP2400_NVRAM_FIRMWARE_OPTIONS1(c) \ ((c)[44] | ((c)[45] << 8) | ((c)[46] << 16) | ((c)[47] << 24)) #define ISP2400_NVRAM_FIRMWARE_OPTIONS2(c) \ ((c)[48] | ((c)[49] << 8) | ((c)[50] << 16) | ((c)[51] << 24)) #define ISP2400_NVRAM_FIRMWARE_OPTIONS3(c) \ ((c)[52] | ((c)[53] << 8) | ((c)[54] << 16) | ((c)[55] << 24)) /* * Qlogic FLT */ #define ISP24XX_BASE_ADDR 0x7ff00000 #define ISP24XX_FLT_ADDR 0x11400 #define ISP25XX_BASE_ADDR ISP24XX_BASE_ADDR #define ISP25XX_FLT_ADDR 0x50400 #define ISP27XX_BASE_ADDR 0x7f800000 #define ISP27XX_FLT_ADDR (0x3F1000 / 4) #define ISP28XX_BASE_ADDR 0x7f7d0000 #define ISP28XX_FLT_ADDR (0x11000 / 4) #define FLT_HEADER_SIZE 8 #define FLT_REGION_SIZE 16 #define FLT_MAX_REGIONS 0xFF #define FLT_REGIONS_SIZE (FLT_REGION_SIZE * FLT_MAX_REGIONS) #define ISP2XXX_FLT_VERSION(c) ((c)[0] | ((c)[1] << 8)) #define ISP2XXX_FLT_LENGTH(c) ((c)[2] | ((c)[3] << 8)) #define ISP2XXX_FLT_CSUM(c) ((c)[4] | ((c)[5] << 8)) #define ISP2XXX_FLT_REG_CODE(c, o) \ ((c)[0 + FLT_REGION_SIZE * o] | ((c)[1 + FLT_REGION_SIZE * o] << 8)) #define ISP2XXX_FLT_REG_ATTR(c, o) ((c)[2 + FLT_REGION_SIZE * o]) #define ISP2XXX_FLT_REG_RES(c, o) ((c)[3 + FLT_REGION_SIZE * o]) #define ISP2XXX_FLT_REG_SIZE(c, o) (\ ((uint32_t)(c)[4 + FLT_REGION_SIZE * o] << 0) | \ ((uint32_t)(c)[5 + FLT_REGION_SIZE * o] << 8) | \ ((uint32_t)(c)[6 + FLT_REGION_SIZE * o] << 16) | \ ((uint32_t)(c)[7 + FLT_REGION_SIZE * o] << 24)) #define ISP2XXX_FLT_REG_START(c, o) (\ ((uint32_t)(c)[8 + FLT_REGION_SIZE * o] << 0) | \ ((uint32_t)(c)[9 + FLT_REGION_SIZE * o] << 8) | \ ((uint32_t)(c)[10 + FLT_REGION_SIZE * o] << 16) | \ ((uint32_t)(c)[11 + FLT_REGION_SIZE * o] << 24)) #define ISP2XXX_FLT_REG_END(c, o) (\ ((uint32_t)(c)[12 + FLT_REGION_SIZE * o] << 0) | \ ((uint32_t)(c)[13 + FLT_REGION_SIZE * o] << 8) | \ ((uint32_t)(c)[14 + FLT_REGION_SIZE * o] << 16) | \ ((uint32_t)(c)[15 + FLT_REGION_SIZE * o] << 24)) struct flt_region { uint16_t code; uint8_t attribute; uint8_t reserved; uint32_t size; uint32_t start; uint32_t end; }; #define FLT_REG_FW 0x01 #define FLT_REG_BOOT_CODE 0x07 #define FLT_REG_VPD_0 0x14 #define FLT_REG_NVRAM_0 0x15 #define FLT_REG_VPD_1 0x16 #define FLT_REG_NVRAM_1 0x17 #define FLT_REG_VPD_2 0xd4 #define FLT_REG_NVRAM_2 0xd5 #define FLT_REG_VPD_3 0xd6 #define FLT_REG_NVRAM_3 0xd7 #define FLT_REG_FDT 0x1a #define FLT_REG_FLT 0x1c #define FLT_REG_NPIV_CONF_0 0x29 #define FLT_REG_NPIV_CONF_1 0x2a #define FLT_REG_GOLD_FW 0x2f #define FLT_REG_FCP_PRIO_0 0x87 #define FLT_REG_FCP_PRIO_1 0x88 /* 27xx */ #define FLT_REG_IMG_PRI_27XX 0x95 #define FLT_REG_IMG_SEC_27XX 0x96 #define FLT_REG_FW_SEC_27XX 0x02 #define FLT_REG_BOOTLOAD_SEC_27XX 0x9 #define FLT_REG_VPD_SEC_27XX_0 0x50 #define FLT_REG_VPD_SEC_27XX_1 0x52 #define FLT_REG_VPD_SEC_27XX_2 0xd8 #define FLT_REG_VPD_SEC_27XX_3 0xda /* 28xx */ #define FLT_REG_AUX_IMG_PRI_28XX 0x125 #define FLT_REG_AUX_IMG_SEC_28XX 0x126 #define FLT_REG_NVRAM_SEC_28XX_0 0x10d #define FLT_REG_NVRAM_SEC_28XX_1 0x10f #define FLT_REG_NVRAM_SEC_28XX_2 0x111 #define FLT_REG_NVRAM_SEC_28XX_3 0x113 #define FLT_REG_VPD_SEC_28XX_0 0x10c #define FLT_REG_VPD_SEC_28XX_1 0x10e #define FLT_REG_VPD_SEC_28XX_2 0x110 #define FLT_REG_VPD_SEC_28XX_3 0x112 #endif /* _ISPREG_H */