/*- * SPDX-License-Identifier: BSD-2-Clause OR GPL-2.0 * * This file is provided under a dual BSD/GPLv2 license. When using or * redistributing this file, you may do so under either license. * * GPL LICENSE SUMMARY * * Copyright(c) 2008 - 2011 Intel Corporation. All rights reserved. * * This program is free software; you can redistribute it and/or modify * it under the terms of version 2 of the GNU General Public License as * published by the Free Software Foundation. * * This program is distributed in the hope that it will be useful, but * WITHOUT ANY WARRANTY; without even the implied warranty of * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU * General Public License for more details. * * You should have received a copy of the GNU General Public License * along with this program; if not, write to the Free Software * Foundation, Inc., 51 Franklin St - Fifth Floor, Boston, MA 02110-1301 USA. * The full GNU General Public License is included in this distribution * in the file called LICENSE.GPL. * * BSD LICENSE * * Copyright(c) 2008 - 2010 Intel Corporation. All rights reserved. * All rights reserved. * * Redistribution and use in source and binary forms, with or without * modification, are permitted provided that the following conditions * are met: * * * Redistributions of source code must retain the above copyright * notice, this list of conditions and the following disclaimer. * * Redistributions in binary form must reproduce the above copyright * notice, this list of conditions and the following disclaimer in * the documentation and/or other materials provided with the * distribution. * * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR * A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT * OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, * SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT * LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, * DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY * THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. */ /** * @file * @brief This file defines all of the SCSI related constants, enumerations, * and types. Please note that this file does not necessarily contain * an exhaustive list of all constants, commands, sub-commands, etc. */ #ifndef _SCSI_H__ #define _SCSI_H__ //****************************************************************************** //* C O N S T A N T S A N D M A C R O S //****************************************************************************** /** * @enum _SCSI_TASK_MGMT_REQUEST_CODES * * @brief This enumberation contains the constants to be used for SCSI task * management request codes. SAM does not specify any particular * values for these codes so constants used here are the same as * those specified in SAS. */ typedef enum _SCSI_TASK_MGMT_REQUEST_CODES { SCSI_TASK_REQUEST_ABORT_TASK = 0x01, SCSI_TASK_REQUEST_ABORT_TASK_SET = 0x02, SCSI_TASK_REQUEST_CLEAR_TASK_SET = 0x04, SCSI_TASK_REQUEST_LOGICAL_UNIT_RESET = 0x08, SCSI_TASK_REQUEST_I_T_NEXUS_RESET = 0x10, SCSI_TASK_REQUEST_CLEAR_ACA = 0x40, SCSI_TASK_REQUEST_QUERY_TASK = 0x80, SCSI_TASK_REQUEST_QUERY_TASK_SET = 0x81, SCSI_TASK_REQUEST_QUERY_UNIT_ATTENTION = 0x82, } SCSI_TASK_MGMT_REQUEST_CODES; /** * @enum _SCSI_TASK_MGMT_RESPONSE_CODES * * @brief This enumeration contains all of the SCSI task management response * codes. */ typedef enum _SCSI_TASK_MGMT_RESPONSE_CODES { SCSI_TASK_MGMT_FUNC_COMPLETE = 0, SCSI_INVALID_FRAME = 2, SCSI_TASK_MGMT_FUNC_NOT_SUPPORTED = 4, SCSI_TASK_MGMT_FUNC_FAILED = 5, SCSI_TASK_MGMT_FUNC_SUCCEEDED = 8, SCSI_INVALID_LUN = 9 } SCSI_TASK_MGMT_RESPONSE_CODES; /** * @enum _SCSI_SENSE_RESPONSE_CODE * * @brief this enumeration depicts the types of sense data responses as * per SPC-3. */ typedef enum _SCSI_SENSE_RESPONSE_CODE { SCSI_FIXED_CURRENT_RESPONSE_CODE = 0x70, SCSI_FIXED_DEFERRED_RESPONSE_CODE = 0x71, SCSI_DESCRIPTOR_CURRENT_RESPONSE_CODE = 0x72, SCSI_DESCRIPTOR_DEFERRED_RESPONSE_CODE = 0x73 } SCSI_SENSE_RESPONSE_CODE; /** * @enum _SCSI_SENSE_DATA_DESCRIPTOR_TYPE * * @brief this enumeration depicts the types of sense data descriptor as * per SPC-4. */ typedef enum _SCSI_SENSE_DATA_DESCRIPTOR_TYPE { SCSI_INFORMATION_DESCRIPTOR_TYPE = 0x00, SCSI_CMD_SPECIFIC_DESCRIPTOR_TYPE = 0x01, SCSI_KEY_SPECIFIC_DESCRIPTOR_TYPE = 0x02, SCSI_FIELD_REPLACEABLE_UNIT_DESCRIPTOR_TYPE = 0x03, SCSI_STREAM_CMD_DESCRIPTOR_TYPE = 0x04, SCSI_BLOCK_DESCRIPTOR_TYPE = 0x05, SCSI_OSD_OBJ_IDENTIFICATION_DESCRIPTOR_TYPE = 0x06, SCSI_OSC_RESPONSE_INTEGRITY_DESCRIPTOR_TYPE = 0x07, SCSI_OSD_ATTR_IDENTIFICATION_DESCRIPTOR_TYPE = 0x08, SCSI_ATA_STATUS_RETURN_DESCRIPTOR_TYPE = 0x09, SCSI_PROGRESS_INDICATION_DESCRIPTOR_TYPE = 0x0a, SCSI_USER_DATA_SEGEMNT_REF_DESCRIPTOR_TYPE = 0x0b } SCSI_SENSE_DATA_DESCRIPTOR_TYPE; #define SCSI_CMD_SPECIFIC_DESCRIPTOR_ADDITIONAL_LENGTH 0x0a #define SCSI_CMD_SPECIFIC_DESCRIPTOR_LENGTH 0x0c #define SCSI_INFORMATION_DESCRIPTOR_ADDITIONAL_LENGTH 0x0a #define SCSI_INFORMATION_DESCRIPTOR_LENGTH 0x0c #define SCSI_BLOCK_DESCRIPTOR_ADDITIONAL_LENGTH 0x2 #define SCSI_BLOCK_DESCRIPTOR_LENGTH 0x4 #define SCSI_SENSE_DATA_DESC_BIT 0x01 // This constant represents the valid bit located in byte 0 of a FIXED // format sense data. #define SCSI_FIXED_SENSE_DATA_VALID_BIT 0x80 #define SCSI_FIXED_SENSE_DATA_BASE_LENGTH 18 // This value is used in the DATAPRES field of the SCSI Response IU. #define SCSI_RESPONSE_DATA_PRES_SENSE_DATA 0x02 /** * @name SCSI_SENSE_KEYS * * These constants delineate all of the SCSI protocol sense key constants */ /*@{*/ #define SCSI_SENSE_NO_SENSE 0x00 #define SCSI_SENSE_RECOVERED_ERROR 0x01 #define SCSI_SENSE_NOT_READY 0x02 #define SCSI_SENSE_MEDIUM_ERROR 0x03 #define SCSI_SENSE_HARDWARE_ERROR 0x04 #define SCSI_SENSE_ILLEGAL_REQUEST 0x05 #define SCSI_SENSE_UNIT_ATTENTION 0x06 #define SCSI_SENSE_DATA_PROTECT 0x07 #define SCSI_SENSE_BLANK_CHECK 0x08 #define SCSI_SENSE_VENDOR_SPECIFIC 0x09 #define SCSI_SENSE_COPY_ABORTED 0x0A #define SCSI_SENSE_ABORTED_COMMAND 0x0B #define SCSI_SENSE_VOLUME_OVERFLOW 0x0D #define SCSI_SENSE_MISCOMPARE 0x0E /*@}*/ /** * @name SCSI_ADDITIONAL_SENSE_CODES * * These constants delineate all of the SCSI protocol additional sense * code constants. */ /*@{*/ #define SCSI_ASC_NO_ADDITIONAL_SENSE 0x00 #define SCSI_ASC_INITIALIZING_COMMAND_REQUIRED 0x04 #define SCSI_ASC_LUN_SELF_TEST_IN_PROGRESS 0x04 #define SCSI_ASC_LUN_FORMAT_IN_PROGRESS 0x04 #define SCSI_ASC_LUN_NOT_RESPOND_TO_SELECTION 0x05 #define SCSI_ASC_UNRECOVERED_READ_ERROR 0x11 #define SCSI_ASC_INVALID_COMMAND_OPERATION_CODE 0x20 #define SCSI_ASC_LBA_OUT_OF_RANGE 0x21 #define SCSI_ASC_INVALID_FIELD_IN_CDB 0x24 #define SCSI_ASC_LOGICAL_UNIT_NOT_SUPPORTED 0x25 #define SCSI_ASC_INVALID_FIELD_IN_PARM_LIST 0x26 #define SCSI_ASC_WRITE_PROTECTED 0x27 #define SCSI_ASC_NOT_READY_TO_READY_CHANGE 0x28 #define SCSI_ASC_MEDIUM_FORMAT_CORRUPTED 0x31 #define SCSI_ASC_ENCLOSURE_SERVICES_UNAVAILABLE 0x35 #define SCSI_ASC_SAVING_PARMS_NOT_SUPPORTED 0x39 #define SCSI_ASC_MEDIUM_NOT_PRESENT 0x3A #define SCSI_ASC_INTERNAL_TARGET_FAILURE 0x44 #define SCSI_ASC_IU_CRC_ERROR_DETECTED 0x47 #define SCSI_ASC_MEDIUM_REMOVAL_REQUEST 0x5A #define SCSI_ASC_COMMAND_SEQUENCE_ERROR 0x2C #define SCSI_ASC_MEDIA_LOAD_OR_EJECT_FAILED 0x53 #define SCSI_ASC_HARDWARE_IMPENDING_FAILURE 0x5D #define SCSI_ASC_POWER_STATE_CHANGE 0x5E #define SCSI_DIAGNOSTIC_FAILURE_ON_COMPONENT 0x40 #define SCSI_ASC_LOGICAL_UNIT_FAILED 0x4C #define SCSI_ASC_ATA_DEVICE_FEATURE_NOT_ENABLED 0x67 #define SCSI_ASC_MICROCODE_HAS_CHANGED 0x3F /*@}*/ /** * @name SCSI_ADDITIONAL_SENSE_CODE_QUALIFIERS * * This enumeration contains all of the used SCSI protocol additional * sense code qualifier constants. */ /*@{*/ #define SCSI_ASCQ_NO_ADDITIONAL_SENSE 0x00 #define SCSI_ASCQ_INVALID_FIELD_IN_CDB 0x00 #define SCSI_ASCQ_INVALID_FIELD_IN_PARM_LIST 0x00 #define SCSI_ASCQ_LUN_NOT_RESPOND_TO_SELECTION 0x00 #define SCSI_ASCQ_INTERNAL_TARGET_FAILURE 0x00 #define SCSI_ASCQ_LBA_OUT_OF_RANGE 0x00 #define SCSI_ASCQ_MEDIUM_NOT_PRESENT 0x00 #define SCSI_ASCQ_NOT_READY_TO_READY_CHANGE 0x00 #define SCSI_ASCQ_WRITE_PROTECTED 0x00 #define SCSI_ASCQ_UNRECOVERED_READ_ERROR 0x00 #define SCSI_ASCQ_SAVING_PARMS_NOT_SUPPORTED 0x00 #define SCSI_ASCQ_INVALID_COMMAND_OPERATION_CODE 0x00 #define SCSI_ASCQ_MEDIUM_REMOVAL_REQUEST 0x01 #define SCSI_ASCQ_INITIALIZING_COMMAND_REQUIRED 0x02 #define SCSI_ASCQ_IU_CRC_ERROR_DETECTED 0x03 #define SCSI_ASCQ_LUN_FORMAT_IN_PROGRESS 0x04 #define SCSI_ASCQ_LUN_SELF_TEST_IN_PROGRESS 0x09 #define SCSI_ASCQ_GENERAL_HARD_DRIVE_FAILURE 0x10 #define SCSI_ASCQ_IDLE_CONDITION_ACTIVATE_BY_COMMAND 0x03 #define SCSI_ASCQ_STANDBY_CONDITION_ACTIVATE_BY_COMMAND 0x04 #define SCSI_ASCQ_POWER_STATE_CHANGE_TO_IDLE 0x42 #define SCSI_ASCQ_POWER_STATE_CHANGE_TO_STANDBY 0x43 #define SCSI_ASCQ_ATA_DEVICE_FEATURE_NOT_ENABLED 0x0B #define SCSI_ASCQ_UNRECOVERED_READ_ERROR_AUTO_REALLOCATE_FAIL 0x04 #define SCSI_ASCQ_ATA_PASS_THROUGH_INFORMATION_AVAILABLE 0x1D #define SCSI_ASCQ_MICROCODE_HAS_CHANGED 0x01 /*@}*/ /** * @name SCSI_STATUS_CODES * * These constants define all of the used SCSI status values. */ /*@{*/ #define SCSI_STATUS_GOOD 0x00 #define SCSI_STATUS_CHECK_CONDITION 0x02 #define SCSI_STATUS_CONDITION_MET 0x04 #define SCSI_STATUS_BUSY 0x08 #define SCSI_STATUS_TASKFULL 0x28 #define SCSI_STATUS_ACA 0x30 #define SCSI_STATUS_ABORT 0x40 /*@}*/ /** * @name SCSI_OPERATION_CODES * * These constants delineate all of the SCSI command/operation codes. */ /*@{*/ #define SCSI_INQUIRY 0x12 #define SCSI_READ_CAPACITY_10 0x25 #define SCSI_SERVICE_ACTION_IN_16 0x9E #define SCSI_TEST_UNIT_READY 0x00 #define SCSI_START_STOP_UNIT 0x1B #define SCSI_SYNCHRONIZE_CACHE_10 0x35 #define SCSI_SYNCHRONIZE_CACHE_16 0x91 #define SCSI_REQUEST_SENSE 0x03 #define SCSI_REPORT_LUNS 0xA0 #define SCSI_REASSIGN_BLOCKS 0x07 #define SCSI_READ_6 0x08 #define SCSI_READ_10 0x28 #define SCSI_READ_12 0xA8 #define SCSI_READ_16 0x88 #define SCSI_WRITE_6 0x0A #define SCSI_WRITE_10 0x2A #define SCSI_WRITE_12 0xAA #define SCSI_WRITE_16 0x8A #define SCSI_VERIFY_10 0x2F #define SCSI_VERIFY_12 0xAF #define SCSI_VERIFY_16 0x8F #define SCSI_SEEK_6 0x01 #define SCSI_SEEK_10 0x02 #define SCSI_WRITE_VERIFY 0x2E #define SCSI_FORMAT_UNIT 0x04 #define SCSI_READ_BUFFER 0x3C #define SCSI_WRITE_BUFFER 0x3B #define SCSI_SEND_DIAGNOSTIC 0x1D #define SCSI_RECEIVE_DIAGNOSTIC 0x1C #define SCSI_MODE_SENSE_6 0x1A #define SCSI_MODE_SENSE_10 0x5A #define SCSI_MODE_SELECT_6 0x15 #define SCSI_MODE_SELECT_10 0x55 #define SCSI_MAINTENANCE_IN 0xA3 #define SCSI_LOG_SENSE 0x4D #define SCSI_LOG_SELECT 0x4C #define SCSI_RESERVE_6 0x16 #define SCSI_RESERVE_10 0x56 #define SCSI_RELEASE_6 0x17 #define SCSI_RELEASE_10 0x57 #define SCSI_ATA_PASSTHRU_12 0xA1 #define SCSI_ATA_PASSTHRU_16 0x85 #define SCSI_WRITE_LONG_10 0x3F #define SCSI_WRITE_LONG_16 0x9F #define SCSI_PERSISTENT_RESERVE_IN 0x5E #define SCSI_PERSISTENT_RESERVE_OUT 0x5F #define SCSI_SECURITY_PROTOCOL_IN 0xA2 #define SCSI_SECURITY_PROTOCOL_OUT 0xB5 #define SCSI_UNMAP 0x42 #define SCSI_WRITE_AND_VERIFY_10 0x2E #define SCSI_WRITE_AND_VERIFY_12 0xAE #define SCSI_WRITE_AND_VERIFY_16 0x8E /*@}*/ /** * @name SCSI_SERVICE_ACTION_IN_CODES * * Service action in operations. */ /*@{*/ #define SCSI_SERVICE_ACTION_IN_CODES_READ_CAPACITY_16 0x10 /*@}*/ /** * * Service action mask. */ /*@{*/ #define SCSI_SERVICE_ACTION_MASK 0x1f /*@}*/ /** * @name SCSI_MAINTENANCE_IN_SERVICE_ACTION_CODES * * MAINTENANCE IN service action codes. */ /*@{*/ #define SCSI_REPORT_TASK_MGMT 0x0D #define SCSI_REPORT_OP_CODES 0x0C /*@}*/ /** * @name SCSI_MODE_PAGE_CONTROLS * * These constants delineate all of the used SCSI Mode Page control * values. */ /*@{*/ #define SCSI_MODE_SENSE_PC_CURRENT 0x0 #define SCSI_MODE_SENSE_PC_CHANGEABLE 0x1 #define SCSI_MODE_SENSE_PC_DEFAULT 0x2 #define SCSI_MODE_SENSE_PC_SAVED 0x3 /*@}*/ #define SCSI_MODE_SENSE_PC_SHIFT 0x06 #define SCSI_MODE_SENSE_PAGE_CODE_ENABLE 0x3F #define SCSI_MODE_SENSE_DBD_ENABLE 0x08 #define SCSI_MODE_SENSE_LLBAA_ENABLE 0x10 #define SCSI_MODE_PAGE_CONTROL_D_SENSE_DISABLE 0x0 #define SCSI_MODE_PAGE_CONTROL_D_SENSE_ENABLE 0x1 /** * @name SCSI_MODE_PAGE_CODES * * These constants delineate all of the used SCSI Mode Page codes. */ /*@{*/ #define SCSI_MODE_PAGE_READ_WRITE_ERROR 0x01 #define SCSI_MODE_PAGE_DISCONNECT_RECONNECT 0x02 #define SCSI_MODE_PAGE_CACHING 0x08 #define SCSI_MODE_PAGE_CONTROL 0x0A #define SCSI_MODE_PAGE_PROTOCOL_SPECIFIC_PORT 0x19 #define SCSI_MODE_PAGE_POWER_CONDITION 0x1A #define SCSI_MODE_PAGE_INFORMATIONAL_EXCP_CONTROL 0x1C #define SCSI_MODE_PAGE_ALL_PAGES 0x3F /*@}*/ #define SCSI_MODE_SENSE_ALL_SUB_PAGES_CODE 0xFF #define SCSI_MODE_SENSE_NO_SUB_PAGES_CODE 0x0 #define SCSI_MODE_SENSE_PROTOCOL_PORT_NUM_SUBPAGES 0x1 #define SCSI_MODE_PAGE_CACHE_PAGE_WCE_BIT 0x04 #define SCSI_MODE_PAGE_CACHE_PAGE_DRA_BIT 0x20 #define SCSI_MODE_PAGE_DEXCPT_ENABLE 0x08 #define SCSI_MODE_SENSE_HEADER_FUA_ENABLE 0x10 #define SCSI_MODE_PAGE_POWER_CONDITION_STANDBY 0x1 #define SCSI_MODE_PAGE_POWER_CONDITION_IDLE 0x2 #define SCSI_MODE_SENSE_6_HEADER_LENGTH 4 #define SCSI_MODE_SENSE_10_HEADER_LENGTH 8 #define SCSI_MODE_SENSE_STD_BLOCK_DESCRIPTOR_LENGTH 8 #define SCSI_MODE_SENSE_LLBA_BLOCK_DESCRIPTOR_LENGTH 16 #define SCSI_MODE_PAGE_INFORMATIONAL_EXCP_DXCPT_ENABLE 0x08 #define SCSI_MODE_PAGE_19_SAS_ID 0x6 #define SCSI_MODE_PAGE_19_SUB1_PAGE_NUM 0x1 #define SCSI_MODE_PAGE_19_SUB1_PC 0x59 #define SCSI_MODE_HEADER_MEDIUM_TYPE_SBC 0x00 //Mode Select constrains related masks value #define SCSI_MODE_SELECT_PF_BIT 0x1 #define SCSI_MODE_SELECT_PF_MASK 0x10 #define SCSI_MODE_SELECT_MODE_PAGE_MRIE_BYTE 0x6 #define SCSI_MODE_SELECT_MODE_PAGE_MRIE_MASK 0x0F #define SCSI_MODE_SELECT_MODE_PAGE_SPF_MASK 0x40 #define SCSI_MODE_SELECT_MODE_PAGE_01_AWRE_MASK 0x80 #define SCSI_MODE_SELECT_MODE_PAGE_01_ARRE_MASK 0x40 #define SCSI_MODE_SELECT_MODE_PAGE_01_RC_ERBITS_MASK 0x1F #define SCSI_MODE_SELECT_MODE_PAGE_08_FSW_LBCSS_NVDIS 0xC1 #define SCSI_MODE_SELECT_MODE_PAGE_1C_PERF_TEST 0x84 #define SCSI_MODE_SELECT_MODE_PAGE_0A_TST_TMF_RLEC 0xF1 #define SCSI_MODE_SELECT_MODE_PAGE_0A_MODIFIER 0xE0 #define SCSI_MODE_SELECT_MODE_PAGE_0A_UA_SWP 0x38 #define SCSI_MODE_SELECT_MODE_PAGE_0A_TAS_AUTO 0x47 #define SCSI_MODE_SELECT_MODE_PAGE_D_SENSE 0x4 #define SCSI_CONTROL_BYTE_NACA_BIT_ENABLE 0x04 #define SCSI_MOVE_FUA_BIT_ENABLE 0x08 #define SCSI_READ_CAPACITY_PMI_BIT_ENABLE 0x01 #define SCSI_READ_CAPACITY_10_DATA_LENGTH 8 #define SCSI_READ_CAPACITY_16_DATA_LENGTH 32 // Inquiry constants #define SCSI_INQUIRY_EVPD_ENABLE 0x01 #define SCSI_INQUIRY_PAGE_CODE_OFFSET 0x02 #define SCSI_INQUIRY_SUPPORTED_PAGES_PAGE 0x00 #define SCSI_INQUIRY_UNIT_SERIAL_NUM_PAGE 0x80 #define SCSI_INQUIRY_DEVICE_ID_PAGE 0x83 #define SCSI_INQUIRY_ATA_INFORMATION_PAGE 0x89 #define SCSI_INQUIRY_BLOCK_DEVICE_PAGE 0xB1 #define SCSI_INQUIRY_BLOCK_DEVICE_LENGTH 0x3C #define SCSI_INQUIRY_STANDARD_ALLOCATION_LENGTH 0x24 //36 #define SCSI_REQUEST_SENSE_ALLOCATION_LENGTH 0xFC //252 /** Defines the log page codes that are use in gathing Smart data */ #define SCSI_LOG_PAGE_SUPPORTED_PAGES 0x00 #define SCSI_LOG_PAGE_INFORMATION_EXCEPTION 0x2F #define SCSI_LOG_PAGE_SELF_TEST 0x10 /** * @name SCSI_INQUIRY_VPD * * The following are constants used with vital product data inquiry pages. * Values are already shifted into the proper nibble location. */ /*@{*/ #define SCSI_PIV_ENABLE 0x80 #define SCSI_LUN_ASSOCIATION 0x00 #define SCSI_TARGET_PORT_ASSOCIATION 0x10 #define SCSI_VEN_UNIQUE_IDENTIFIER_TYPE 0x00 #define SCSI_NAA_IDENTIFIER_TYPE 0x03 #define SCSI_T10_IDENTIFIER_TYPE 0x01 #define SCSI_BINARY_CODE_SET 0x01 #define SCSI_ASCII_CODE_SET 0x02 #define SCSI_FC_PROTOCOL_IDENTIFIER 0x00 #define SCSI_SAS_PROTOCOL_IDENTIFIER 0x60 /*@}*/ #define SCSI_VERIFY_BYTCHK_ENABLED 0x02 #define SCSI_SYNCHRONIZE_CACHE_IMMED_ENABLED 0x02 /** * @name SCSI_START_STOP_UNIT_POWER_CONDITION_CODES * * The following are SCSI Start Stop Unit command Power Condition codes. */ /*@{*/ #define SCSI_START_STOP_UNIT_POWER_CONDITION_START_VALID 0x0 #define SCSI_START_STOP_UNIT_POWER_CONDITION_ACTIVE 0x1 #define SCSI_START_STOP_UNIT_POWER_CONDITION_IDLE 0x2 #define SCSI_START_STOP_UNIT_POWER_CONDITION_STANDBY 0x3 #define SCSI_START_STOP_UNIT_POWER_CONDITION_LU_CONTROL 0x7 #define SCSI_START_STOP_UNIT_POWER_CONDITION_FORCE_S_CONTROL 0xB /*@}*/ #define SCSI_START_STOP_UNIT_IMMED_MASK 0x1 #define SCSI_START_STOP_UNIT_IMMED_SHIFT 0 #define SCSI_START_STOP_UNIT_START_BIT_MASK 0x1 #define SCSI_START_STOP_UNIT_START_BIT_SHIFT 0 #define SCSI_START_STOP_UNIT_LOEJ_BIT_MASK 0x2 #define SCSI_START_STOP_UNIT_LOEJ_BIT_SHIFT 1 #define SCSI_START_STOP_UNIT_NO_FLUSH_MASK 0x4 #define SCSI_START_STOP_UNIT_NO_FLUSH_SHIFT 2 #define SCSI_START_STOP_UNIT_POWER_CONDITION_MODIFIER_MASK 0xF #define SCSI_START_STOP_UNIT_POWER_CONDITION_MODIFIER_SHIFT 0 #define SCSI_START_STOP_UNIT_POWER_CONDITION_MASK 0xF0 #define SCSI_START_STOP_UNIT_POWER_CONDITION_SHIFT 4 #define SCSI_LOG_SENSE_PC_FIELD_MASK 0xC0 #define SCSI_LOG_SENSE_PC_FIELD_SHIFT 6 #define SCSI_LOG_SENSE_PAGE_CODE_FIELD_MASK 0x3F #define SCSI_LOG_SENSE_PAGE_CODE_FIELD_SHIFT 0 /** * @name MRIE - Method of reporting informational exceptions codes */ /*@{*/ #define NO_REPORTING_INFO_EXCEPTION_CONDITION 0x0 #define ASYNCHRONOUS_EVENT_REPORTING 0x1 #define ESTABLISH_UNIT_ATTENTION_CONDITION 0x2 #define CONDITIONALLY_GENERATE_RECOVERED_ERROR 0x3 #define UNCONDITIONALLY_GENERATE_RECOVERED_ERROR 0x4 #define GENERATE_NO_SENSE 0x5 #define REPORT_INFO_EXCEPTION_CONDITION_ON_REQUEST 0x6 /*@}*/ #define SCSI_INFORMATION_EXCEPTION_DEXCPT_BIT 0x08 //Reassign Blocks masks #define SCSI_REASSIGN_BLOCKS_LONGLBA_BIT 0x02 #define SCSI_REASSIGN_BLOCKS_LONGLIST_BIT 0x01 #endif // _SCSI_H_