/*- * SPDX-License-Identifier: BSD-3-Clause * * Copyright (c) 2011 * Ben Gray . * All rights reserved. * * Redistribution and use in source and binary forms, with or without * modification, are permitted provided that the following conditions * are met: * 1. Redistributions of source code must retain the above copyright * notice, this list of conditions and the following disclaimer. * 2. Redistributions in binary form must reproduce the above copyright * notice, this list of conditions and the following disclaimer in the * documentation and/or other materials provided with the distribution. * 3. The name of the company nor the name of the author may be used to * endorse or promote products derived from this software without specific * prior written permission. * * THIS SOFTWARE IS PROVIDED BY BEN GRAY ``AS IS'' AND ANY EXPRESS OR * IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES * OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. * IN NO EVENT SHALL BEN GRAY BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, * SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, * PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; * OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, * WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR * OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF * ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. */ #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include /* * This file defines the clock configuration for the OMAP4xxx series of * devices. * * How This is Suppose to Work * =========================== * - There is a top level omap_prcm module that defines all OMAP SoC drivers * should use to enable/disable the system clocks regardless of the version * of OMAP device they are running on. This top level PRCM module is just * a thin shim to chip specific functions that perform the donkey work of * configuring the clock - this file is the 'donkey' for OMAP44xx devices. * * - The key bit in this file is the omap_clk_devmap array, it's * used by the omap_prcm driver to determine what clocks are valid and which * functions to call to manipulate them. * * - In essence you just need to define some callbacks for each of the * clocks and then you're done. * * - The other thing that is worth noting is that when the omap_prcm device * is registered you typically pass in some memory ranges which are the * SYS_MEMORY resources. These resources are in turn allocated using * bus_allocate_resources(...) and the resource handles are passed to all * individual clock callback handlers. * * * * OMAP4 devices are different from the previous OMAP3 devices in that there * is no longer a separate functional and interface clock for each module, * instead there is typically an interface clock that spans many modules. */ #define FREQ_96MHZ 96000000 #define FREQ_64MHZ 64000000 #define FREQ_48MHZ 48000000 #define FREQ_32KHZ 32000 #define PRM_INSTANCE 1 #define CM1_INSTANCE 2 #define CM2_INSTANCE 3 /** * Address offsets from the PRM memory region to the top level clock control * registers. */ #define CKGEN_PRM_OFFSET 0x00000100UL #define MPU_PRM_OFFSET 0x00000300UL #define DSP_PRM_OFFSET 0x00000400UL #define ABE_PRM_OFFSET 0x00000500UL #define ALWAYS_ON_PRM_OFFSET 0x00000600UL #define CORE_PRM_OFFSET 0x00000700UL #define IVAHD_PRM_OFFSET 0x00000F00UL #define CAM_PRM_OFFSET 0x00001000UL #define DSS_PRM_OFFSET 0x00001100UL #define SGX_PRM_OFFSET 0x00001200UL #define L3INIT_PRM_OFFSET 0x00001300UL #define L4PER_PRM_OFFSET 0x00001400UL #define WKUP_PRM_OFFSET 0x00001700UL #define WKUP_CM_OFFSET 0x00001800UL #define EMU_PRM_OFFSET 0x00001900UL #define EMU_CM_OFFSET 0x00001A00UL #define DEVICE_PRM_OFFSET 0x00001B00UL #define INSTR_PRM_OFFSET 0x00001F00UL #define CM_ABE_DSS_SYS_CLKSEL_OFFSET (CKGEN_PRM_OFFSET + 0x0000UL) #define CM_L4_WKUP_CLKSELL_OFFSET (CKGEN_PRM_OFFSET + 0x0008UL) #define CM_ABE_PLL_REF_CLKSEL_OFFSET (CKGEN_PRM_OFFSET + 0x000CUL) #define CM_SYS_CLKSEL_OFFSET (CKGEN_PRM_OFFSET + 0x0010UL) /** * Address offsets from the CM1 memory region to the top level clock control * registers. */ #define CKGEN_CM1_OFFSET 0x00000100UL #define MPU_CM1_OFFSET 0x00000300UL #define DSP_CM1_OFFSET 0x00000400UL #define ABE_CM1_OFFSET 0x00000500UL #define RESTORE_CM1_OFFSET 0x00000E00UL #define INSTR_CM1_OFFSET 0x00000F00UL #define CM_CLKSEL_DPLL_MPU (CKGEN_CM1_OFFSET + 0x006CUL) /** * Address offsets from the CM2 memory region to the top level clock control * registers. */ #define INTRCONN_SOCKET_CM2_OFFSET 0x00000000UL #define CKGEN_CM2_OFFSET 0x00000100UL #define ALWAYS_ON_CM2_OFFSET 0x00000600UL #define CORE_CM2_OFFSET 0x00000700UL #define IVAHD_CM2_OFFSET 0x00000F00UL #define CAM_CM2_OFFSET 0x00001000UL #define DSS_CM2_OFFSET 0x00001100UL #define SGX_CM2_OFFSET 0x00001200UL #define L3INIT_CM2_OFFSET 0x00001300UL #define L4PER_CM2_OFFSET 0x00001400UL #define RESTORE_CM2_OFFSET 0x00001E00UL #define INSTR_CM2_OFFSET 0x00001F00UL #define CLKCTRL_MODULEMODE_MASK 0x00000003UL #define CLKCTRL_MODULEMODE_DISABLE 0x00000000UL #define CLKCTRL_MODULEMODE_AUTO 0x00000001UL #define CLKCTRL_MODULEMODE_ENABLE 0x00000001UL #define CLKCTRL_IDLEST_MASK 0x00030000UL #define CLKCTRL_IDLEST_ENABLED 0x00000000UL #define CLKCTRL_IDLEST_WAKING 0x00010000UL #define CLKCTRL_IDLEST_IDLE 0x00020000UL #define CLKCTRL_IDLEST_DISABLED 0x00030000UL static struct ofw_compat_data compat_data[] = { {"ti,omap4-cm1", (uintptr_t)CM1_INSTANCE}, {"ti,omap4-cm2", (uintptr_t)CM2_INSTANCE}, {"ti,omap4-prm", (uintptr_t)PRM_INSTANCE}, {NULL, (uintptr_t)0}, }; struct omap4_prcm_softc { struct resource *sc_res; int sc_rid; int sc_instance; int attach_done; }; static int omap4_clk_generic_activate(struct ti_clock_dev *clkdev); static int omap4_clk_generic_deactivate(struct ti_clock_dev *clkdev); static int omap4_clk_generic_accessible(struct ti_clock_dev *clkdev); static int omap4_clk_generic_set_source(struct ti_clock_dev *clkdev, clk_src_t clksrc); static int omap4_clk_generic_get_source_freq(struct ti_clock_dev *clkdev, unsigned int *freq); static int omap4_clk_gptimer_set_source(struct ti_clock_dev *clkdev, clk_src_t clksrc); static int omap4_clk_gptimer_get_source_freq(struct ti_clock_dev *clkdev, unsigned int *freq); static int omap4_clk_hsmmc_set_source(struct ti_clock_dev *clkdev, clk_src_t clksrc); static int omap4_clk_hsmmc_get_source_freq(struct ti_clock_dev *clkdev, unsigned int *freq); static int omap4_clk_hsusbhost_set_source(struct ti_clock_dev *clkdev, clk_src_t clksrc); static int omap4_clk_hsusbhost_activate(struct ti_clock_dev *clkdev); static int omap4_clk_hsusbhost_deactivate(struct ti_clock_dev *clkdev); static int omap4_clk_hsusbhost_accessible(struct ti_clock_dev *clkdev); static int omap4_clk_get_sysclk_freq(struct ti_clock_dev *clkdev, unsigned int *freq); static int omap4_clk_get_arm_fclk_freq(struct ti_clock_dev *clkdev, unsigned int *freq); /** * omap_clk_devmap - Array of clock devices available on OMAP4xxx devices * * This map only defines which clocks are valid and the callback functions * for clock activate, deactivate, etc. It is used by the top level omap_prcm * driver. * * The actual details of the clocks (config registers, bit fields, sources, * etc) are in the private g_omap3_clk_details array below. * */ #define OMAP4_GENERIC_CLOCK_DEV(i) \ { .id = (i), \ .clk_activate = omap4_clk_generic_activate, \ .clk_deactivate = omap4_clk_generic_deactivate, \ .clk_set_source = omap4_clk_generic_set_source, \ .clk_accessible = omap4_clk_generic_accessible, \ .clk_get_source_freq = omap4_clk_generic_get_source_freq, \ .clk_set_source_freq = NULL \ } #define OMAP4_GPTIMER_CLOCK_DEV(i) \ { .id = (i), \ .clk_activate = omap4_clk_generic_activate, \ .clk_deactivate = omap4_clk_generic_deactivate, \ .clk_set_source = omap4_clk_gptimer_set_source, \ .clk_accessible = omap4_clk_generic_accessible, \ .clk_get_source_freq = omap4_clk_gptimer_get_source_freq, \ .clk_set_source_freq = NULL \ } #define OMAP4_HSMMC_CLOCK_DEV(i) \ { .id = (i), \ .clk_activate = omap4_clk_generic_activate, \ .clk_deactivate = omap4_clk_generic_deactivate, \ .clk_set_source = omap4_clk_hsmmc_set_source, \ .clk_accessible = omap4_clk_generic_accessible, \ .clk_get_source_freq = omap4_clk_hsmmc_get_source_freq, \ .clk_set_source_freq = NULL \ } #define OMAP4_HSUSBHOST_CLOCK_DEV(i) \ { .id = (i), \ .clk_activate = omap4_clk_hsusbhost_activate, \ .clk_deactivate = omap4_clk_hsusbhost_deactivate, \ .clk_set_source = omap4_clk_hsusbhost_set_source, \ .clk_accessible = omap4_clk_hsusbhost_accessible, \ .clk_get_source_freq = NULL, \ .clk_set_source_freq = NULL \ } struct ti_clock_dev ti_omap4_clk_devmap[] = { /* System clocks */ { .id = SYS_CLK, .clk_activate = NULL, .clk_deactivate = NULL, .clk_set_source = NULL, .clk_accessible = NULL, .clk_get_source_freq = omap4_clk_get_sysclk_freq, .clk_set_source_freq = NULL, }, /* MPU (ARM) core clocks */ { .id = MPU_CLK, .clk_activate = NULL, .clk_deactivate = NULL, .clk_set_source = NULL, .clk_accessible = NULL, .clk_get_source_freq = omap4_clk_get_arm_fclk_freq, .clk_set_source_freq = NULL, }, /* UART device clocks */ OMAP4_GENERIC_CLOCK_DEV(UART1_CLK), OMAP4_GENERIC_CLOCK_DEV(UART2_CLK), OMAP4_GENERIC_CLOCK_DEV(UART3_CLK), OMAP4_GENERIC_CLOCK_DEV(UART4_CLK), /* Timer device source clocks */ OMAP4_GPTIMER_CLOCK_DEV(TIMER1_CLK), OMAP4_GPTIMER_CLOCK_DEV(TIMER2_CLK), OMAP4_GPTIMER_CLOCK_DEV(TIMER3_CLK), OMAP4_GPTIMER_CLOCK_DEV(TIMER4_CLK), OMAP4_GPTIMER_CLOCK_DEV(TIMER5_CLK), OMAP4_GPTIMER_CLOCK_DEV(TIMER6_CLK), OMAP4_GPTIMER_CLOCK_DEV(TIMER7_CLK), OMAP4_GPTIMER_CLOCK_DEV(TIMER8_CLK), OMAP4_GPTIMER_CLOCK_DEV(TIMER9_CLK), OMAP4_GPTIMER_CLOCK_DEV(TIMER10_CLK), OMAP4_GPTIMER_CLOCK_DEV(TIMER11_CLK), /* MMC device clocks (MMC1 and MMC2 can have different input clocks) */ OMAP4_HSMMC_CLOCK_DEV(MMC1_CLK), OMAP4_HSMMC_CLOCK_DEV(MMC2_CLK), OMAP4_GENERIC_CLOCK_DEV(MMC3_CLK), OMAP4_GENERIC_CLOCK_DEV(MMC4_CLK), OMAP4_GENERIC_CLOCK_DEV(MMC5_CLK), /* USB HS (high speed TLL, EHCI and OHCI) */ OMAP4_HSUSBHOST_CLOCK_DEV(USBTLL_CLK), OMAP4_HSUSBHOST_CLOCK_DEV(USBHSHOST_CLK), OMAP4_HSUSBHOST_CLOCK_DEV(USBFSHOST_CLK), OMAP4_HSUSBHOST_CLOCK_DEV(USBP1_PHY_CLK), OMAP4_HSUSBHOST_CLOCK_DEV(USBP2_PHY_CLK), OMAP4_HSUSBHOST_CLOCK_DEV(USBP1_UTMI_CLK), OMAP4_HSUSBHOST_CLOCK_DEV(USBP2_UTMI_CLK), OMAP4_HSUSBHOST_CLOCK_DEV(USBP1_HSIC_CLK), OMAP4_HSUSBHOST_CLOCK_DEV(USBP2_HSIC_CLK), /* GPIO */ OMAP4_GENERIC_CLOCK_DEV(GPIO1_CLK), OMAP4_GENERIC_CLOCK_DEV(GPIO2_CLK), OMAP4_GENERIC_CLOCK_DEV(GPIO3_CLK), OMAP4_GENERIC_CLOCK_DEV(GPIO4_CLK), OMAP4_GENERIC_CLOCK_DEV(GPIO5_CLK), OMAP4_GENERIC_CLOCK_DEV(GPIO6_CLK), /* sDMA */ OMAP4_GENERIC_CLOCK_DEV(SDMA_CLK), /* I2C */ OMAP4_GENERIC_CLOCK_DEV(I2C1_CLK), OMAP4_GENERIC_CLOCK_DEV(I2C2_CLK), OMAP4_GENERIC_CLOCK_DEV(I2C3_CLK), OMAP4_GENERIC_CLOCK_DEV(I2C4_CLK), { INVALID_CLK_IDENT, NULL, NULL, NULL, NULL } }; /** * omap4_clk_details - Stores details for all the different clocks supported * * Whenever an operation on a clock is being performed (activated, deactivated, * etc) this array is looked up to find the correct register and bit(s) we * should be modifying. * */ struct omap4_clk_details { clk_ident_t id; uint32_t instance; uint32_t clksel_reg; int32_t src_freq; uint32_t enable_mode; }; #define OMAP4_GENERIC_CLOCK_DETAILS(i, f, di, r, e) \ { .id = (i), \ .instance = (di), \ .clksel_reg = (r), \ .src_freq = (f), \ .enable_mode = (e), \ } static struct omap4_clk_details g_omap4_clk_details[] = { /* UART */ OMAP4_GENERIC_CLOCK_DETAILS(UART1_CLK, FREQ_48MHZ, CM2_INSTANCE, (L4PER_CM2_OFFSET + 0x0140), CLKCTRL_MODULEMODE_ENABLE), OMAP4_GENERIC_CLOCK_DETAILS(UART2_CLK, FREQ_48MHZ, CM2_INSTANCE, (L4PER_CM2_OFFSET + 0x0148), CLKCTRL_MODULEMODE_ENABLE), OMAP4_GENERIC_CLOCK_DETAILS(UART3_CLK, FREQ_48MHZ, CM2_INSTANCE, (L4PER_CM2_OFFSET + 0x0150), CLKCTRL_MODULEMODE_ENABLE), OMAP4_GENERIC_CLOCK_DETAILS(UART4_CLK, FREQ_48MHZ, CM2_INSTANCE, (L4PER_CM2_OFFSET + 0x0158), CLKCTRL_MODULEMODE_ENABLE), /* General purpose timers */ OMAP4_GENERIC_CLOCK_DETAILS(TIMER1_CLK, -1, PRM_INSTANCE, (WKUP_CM_OFFSET + 0x040), CLKCTRL_MODULEMODE_ENABLE), OMAP4_GENERIC_CLOCK_DETAILS(TIMER2_CLK, -1, CM2_INSTANCE, (L4PER_CM2_OFFSET + 0x038), CLKCTRL_MODULEMODE_ENABLE), OMAP4_GENERIC_CLOCK_DETAILS(TIMER3_CLK, -1, CM2_INSTANCE, (L4PER_CM2_OFFSET + 0x040), CLKCTRL_MODULEMODE_ENABLE), OMAP4_GENERIC_CLOCK_DETAILS(TIMER4_CLK, -1, CM2_INSTANCE, (L4PER_CM2_OFFSET + 0x048), CLKCTRL_MODULEMODE_ENABLE), OMAP4_GENERIC_CLOCK_DETAILS(TIMER5_CLK, -1, CM1_INSTANCE, (ABE_CM1_OFFSET + 0x068), CLKCTRL_MODULEMODE_ENABLE), OMAP4_GENERIC_CLOCK_DETAILS(TIMER6_CLK, -1, CM1_INSTANCE, (ABE_CM1_OFFSET + 0x070), CLKCTRL_MODULEMODE_ENABLE), OMAP4_GENERIC_CLOCK_DETAILS(TIMER7_CLK, -1, CM1_INSTANCE, (ABE_CM1_OFFSET + 0x078), CLKCTRL_MODULEMODE_ENABLE), OMAP4_GENERIC_CLOCK_DETAILS(TIMER8_CLK, -1, CM1_INSTANCE, (ABE_CM1_OFFSET + 0x080), CLKCTRL_MODULEMODE_ENABLE), OMAP4_GENERIC_CLOCK_DETAILS(TIMER9_CLK, -1, CM2_INSTANCE, (L4PER_CM2_OFFSET + 0x050), CLKCTRL_MODULEMODE_ENABLE), OMAP4_GENERIC_CLOCK_DETAILS(TIMER10_CLK, -1, CM2_INSTANCE, (L4PER_CM2_OFFSET + 0x028), CLKCTRL_MODULEMODE_ENABLE), OMAP4_GENERIC_CLOCK_DETAILS(TIMER11_CLK, -1, CM2_INSTANCE, (L4PER_CM2_OFFSET + 0x030), CLKCTRL_MODULEMODE_ENABLE), /* HSMMC (MMC1 and MMC2 can have different input clocks) */ OMAP4_GENERIC_CLOCK_DETAILS(MMC1_CLK, -1, CM2_INSTANCE, (L3INIT_CM2_OFFSET + 0x028), /*CLKCTRL_MODULEMODE_ENABLE*/2), OMAP4_GENERIC_CLOCK_DETAILS(MMC2_CLK, -1, CM2_INSTANCE, (L3INIT_CM2_OFFSET + 0x030), /*CLKCTRL_MODULEMODE_ENABLE*/2), OMAP4_GENERIC_CLOCK_DETAILS(MMC3_CLK, FREQ_48MHZ, CM2_INSTANCE, (L4PER_CM2_OFFSET + 0x120), /*CLKCTRL_MODULEMODE_ENABLE*/2), OMAP4_GENERIC_CLOCK_DETAILS(MMC4_CLK, FREQ_48MHZ, CM2_INSTANCE, (L4PER_CM2_OFFSET + 0x128), /*CLKCTRL_MODULEMODE_ENABLE*/2), OMAP4_GENERIC_CLOCK_DETAILS(MMC5_CLK, FREQ_48MHZ, CM2_INSTANCE, (L4PER_CM2_OFFSET + 0x160), /*CLKCTRL_MODULEMODE_ENABLE*/1), /* GPIO modules */ OMAP4_GENERIC_CLOCK_DETAILS(GPIO1_CLK, -1, PRM_INSTANCE, (WKUP_CM_OFFSET + 0x038), CLKCTRL_MODULEMODE_AUTO), OMAP4_GENERIC_CLOCK_DETAILS(GPIO2_CLK, -1, CM2_INSTANCE, (L4PER_CM2_OFFSET + 0x060), CLKCTRL_MODULEMODE_AUTO), OMAP4_GENERIC_CLOCK_DETAILS(GPIO3_CLK, -1, CM2_INSTANCE, (L4PER_CM2_OFFSET + 0x068), CLKCTRL_MODULEMODE_AUTO), OMAP4_GENERIC_CLOCK_DETAILS(GPIO4_CLK, -1, CM2_INSTANCE, (L4PER_CM2_OFFSET + 0x070), CLKCTRL_MODULEMODE_AUTO), OMAP4_GENERIC_CLOCK_DETAILS(GPIO5_CLK, -1, CM2_INSTANCE, (L4PER_CM2_OFFSET + 0x078), CLKCTRL_MODULEMODE_AUTO), OMAP4_GENERIC_CLOCK_DETAILS(GPIO6_CLK, -1, CM2_INSTANCE, (L4PER_CM2_OFFSET + 0x080), CLKCTRL_MODULEMODE_AUTO), /* sDMA block */ OMAP4_GENERIC_CLOCK_DETAILS(SDMA_CLK, -1, CM2_INSTANCE, (CORE_CM2_OFFSET + 0x300), CLKCTRL_MODULEMODE_AUTO), /* I2C modules */ OMAP4_GENERIC_CLOCK_DETAILS(I2C1_CLK, -1, CM2_INSTANCE, (L4PER_CM2_OFFSET + 0x0A0), CLKCTRL_MODULEMODE_ENABLE), OMAP4_GENERIC_CLOCK_DETAILS(I2C2_CLK, -1, CM2_INSTANCE, (L4PER_CM2_OFFSET + 0x0A8), CLKCTRL_MODULEMODE_ENABLE), OMAP4_GENERIC_CLOCK_DETAILS(I2C3_CLK, -1, CM2_INSTANCE, (L4PER_CM2_OFFSET + 0x0B0), CLKCTRL_MODULEMODE_ENABLE), OMAP4_GENERIC_CLOCK_DETAILS(I2C4_CLK, -1, CM2_INSTANCE, (L4PER_CM2_OFFSET + 0x0B8), CLKCTRL_MODULEMODE_ENABLE), { INVALID_CLK_IDENT, 0, 0, 0, 0 }, }; /** * MAX_MODULE_ENABLE_WAIT - the number of loops to wait for the module to come * alive. * */ #define MAX_MODULE_ENABLE_WAIT 100 /** * ARRAY_SIZE - Macro to return the number of elements in a static const array. * */ #define ARRAY_SIZE(x) (sizeof(x)/sizeof(x[0])) /** * omap4_clk_details - writes a 32-bit value to one of the timer registers * @timer: Timer device context * @off: The offset of a register from the timer register address range * @val: The value to write into the register * * * RETURNS: * nothing */ static struct omap4_clk_details* omap4_clk_details(clk_ident_t id) { struct omap4_clk_details *walker; for (walker = g_omap4_clk_details; walker->id != INVALID_CLK_IDENT; walker++) { if (id == walker->id) return (walker); } return NULL; } static struct omap4_prcm_softc * omap4_prcm_get_instance_softc(int module_instance) { int i, maxunit; devclass_t prcm_devclass; device_t dev; struct omap4_prcm_softc *sc; prcm_devclass = devclass_find("omap4_prcm"); maxunit = devclass_get_maxunit(prcm_devclass); for (i = 0; i < maxunit; i++) { dev = devclass_get_device(prcm_devclass, i); sc = device_get_softc(dev); if (sc->sc_instance == module_instance) return (sc); } return (NULL); } /** * omap4_clk_generic_activate - checks if a module is accessible * @module: identifier for the module to check, see omap3_prcm.h for a list * of possible modules. * Example: OMAP3_MODULE_MMC1 * * * * LOCKING: * Inherits the locks from the omap_prcm driver, no internal locking. * * RETURNS: * Returns 0 on success or a positive error code on failure. */ static int omap4_clk_generic_activate(struct ti_clock_dev *clkdev) { struct omap4_prcm_softc *sc; struct omap4_clk_details* clk_details; struct resource* clk_mem_res; uint32_t clksel; unsigned int i; clk_details = omap4_clk_details(clkdev->id); if (clk_details == NULL) return (ENXIO); sc = omap4_prcm_get_instance_softc(clk_details->instance); if (sc == NULL) return ENXIO; clk_mem_res = sc->sc_res; if (clk_mem_res == NULL) return (EINVAL); /* All the 'generic' clocks have a CLKCTRL register which is more or less * generic - the have at least two fielda called MODULEMODE and IDLEST. */ clksel = bus_read_4(clk_mem_res, clk_details->clksel_reg); clksel &= ~CLKCTRL_MODULEMODE_MASK; clksel |= clk_details->enable_mode; bus_write_4(clk_mem_res, clk_details->clksel_reg, clksel); /* Now poll on the IDLEST register to tell us if the module has come up. * TODO: We need to take into account the parent clocks. */ /* Try MAX_MODULE_ENABLE_WAIT number of times to check if enabled */ for (i = 0; i < MAX_MODULE_ENABLE_WAIT; i++) { clksel = bus_read_4(clk_mem_res, clk_details->clksel_reg); if ((clksel & CLKCTRL_IDLEST_MASK) == CLKCTRL_IDLEST_ENABLED) break; DELAY(10); } /* Check the enabled state */ if ((clksel & CLKCTRL_IDLEST_MASK) != CLKCTRL_IDLEST_ENABLED) { printf("Error: failed to enable module with clock %d\n", clkdev->id); printf("Error: 0x%08x => 0x%08x\n", clk_details->clksel_reg, clksel); return (ETIMEDOUT); } return (0); } /** * omap4_clk_generic_deactivate - checks if a module is accessible * @module: identifier for the module to check, see omap3_prcm.h for a list * of possible modules. * Example: OMAP3_MODULE_MMC1 * * * * LOCKING: * Inherits the locks from the omap_prcm driver, no internal locking. * * RETURNS: * Returns 0 on success or a positive error code on failure. */ static int omap4_clk_generic_deactivate(struct ti_clock_dev *clkdev) { struct omap4_prcm_softc *sc; struct omap4_clk_details* clk_details; struct resource* clk_mem_res; uint32_t clksel; clk_details = omap4_clk_details(clkdev->id); if (clk_details == NULL) return (ENXIO); sc = omap4_prcm_get_instance_softc(clk_details->instance); if (sc == NULL) return ENXIO; clk_mem_res = sc->sc_res; if (clk_mem_res == NULL) return (EINVAL); /* All the 'generic' clocks have a CLKCTRL register which is more or less * generic - the have at least two fielda called MODULEMODE and IDLEST. */ clksel = bus_read_4(clk_mem_res, clk_details->clksel_reg); clksel &= ~CLKCTRL_MODULEMODE_MASK; clksel |= CLKCTRL_MODULEMODE_DISABLE; bus_write_4(clk_mem_res, clk_details->clksel_reg, clksel); return (0); } /** * omap4_clk_generic_set_source - checks if a module is accessible * @module: identifier for the module to check, see omap3_prcm.h for a list * of possible modules. * Example: OMAP3_MODULE_MMC1 * * * * LOCKING: * Inherits the locks from the omap_prcm driver, no internal locking. * * RETURNS: * Returns 0 on success or a positive error code on failure. */ static int omap4_clk_generic_set_source(struct ti_clock_dev *clkdev, clk_src_t clksrc) { return (0); } /** * omap4_clk_generic_accessible - checks if a module is accessible * @module: identifier for the module to check, see omap3_prcm.h for a list * of possible modules. * Example: OMAP3_MODULE_MMC1 * * * * LOCKING: * Inherits the locks from the omap_prcm driver, no internal locking. * * RETURNS: * Returns 0 on success or a negative error code on failure. */ static int omap4_clk_generic_accessible(struct ti_clock_dev *clkdev) { struct omap4_prcm_softc *sc; struct omap4_clk_details* clk_details; struct resource* clk_mem_res; uint32_t clksel; clk_details = omap4_clk_details(clkdev->id); if (clk_details == NULL) return (ENXIO); sc = omap4_prcm_get_instance_softc(clk_details->instance); if (sc == NULL) return ENXIO; clk_mem_res = sc->sc_res; if (clk_mem_res == NULL) return (EINVAL); clksel = bus_read_4(clk_mem_res, clk_details->clksel_reg); /* Check the enabled state */ if ((clksel & CLKCTRL_IDLEST_MASK) != CLKCTRL_IDLEST_ENABLED) return (0); return (1); } /** * omap4_clk_generic_get_source_freq - checks if a module is accessible * @module: identifier for the module to check, see omap3_prcm.h for a list * of possible modules. * Example: OMAP3_MODULE_MMC1 * * * * LOCKING: * Inherits the locks from the omap_prcm driver, no internal locking. * * RETURNS: * Returns 0 on success or a negative error code on failure. */ static int omap4_clk_generic_get_source_freq(struct ti_clock_dev *clkdev, unsigned int *freq ) { struct omap4_clk_details* clk_details = omap4_clk_details(clkdev->id); if (clk_details == NULL) return (ENXIO); /* Simply return the stored frequency */ if (freq) *freq = (unsigned int)clk_details->src_freq; return (0); } /** * omap4_clk_gptimer_set_source - checks if a module is accessible * @module: identifier for the module to check, see omap3_prcm.h for a list * of possible modules. * Example: OMAP3_MODULE_MMC1 * * * * LOCKING: * Inherits the locks from the omap_prcm driver, no internal locking. * * RETURNS: * Returns 0 on success or a negative error code on failure. */ static int omap4_clk_gptimer_set_source(struct ti_clock_dev *clkdev, clk_src_t clksrc) { struct omap4_prcm_softc *sc; struct omap4_clk_details* clk_details; struct resource* clk_mem_res; clk_details = omap4_clk_details(clkdev->id); if (clk_details == NULL) return (ENXIO); sc = omap4_prcm_get_instance_softc(clk_details->instance); if (sc == NULL) return ENXIO; clk_mem_res = sc->sc_res; if (clk_mem_res == NULL) return (EINVAL); /* TODO: Implement */ return (0); } /** * omap4_clk_gptimer_get_source_freq - checks if a module is accessible * @module: identifier for the module to check, see omap3_prcm.h for a list * of possible modules. * Example: OMAP3_MODULE_MMC1 * * * * LOCKING: * Inherits the locks from the omap_prcm driver, no internal locking. * * RETURNS: * Returns 0 on success or a negative error code on failure. */ static int omap4_clk_gptimer_get_source_freq(struct ti_clock_dev *clkdev, unsigned int *freq ) { struct omap4_prcm_softc *sc; struct omap4_clk_details* clk_details; struct resource* clk_mem_res; uint32_t clksel; unsigned int src_freq; clk_details = omap4_clk_details(clkdev->id); if (clk_details == NULL) return (ENXIO); sc = omap4_prcm_get_instance_softc(clk_details->instance); if (sc == NULL) return ENXIO; clk_mem_res = sc->sc_res; if (clk_mem_res == NULL) return (EINVAL); /* Need to read the CLKSEL field to determine the clock source */ clksel = bus_read_4(clk_mem_res, clk_details->clksel_reg); if (clksel & (0x1UL << 24)) src_freq = FREQ_32KHZ; else omap4_clk_get_sysclk_freq(NULL, &src_freq); /* Return the frequency */ if (freq) *freq = src_freq; return (0); } /** * omap4_clk_hsmmc_set_source - sets the source clock (freq) * @clkdev: pointer to the clockdev structure (id field will contain clock id) * * The MMC 1 and 2 clocks can be source from either a 64MHz or 96MHz clock. * * LOCKING: * Inherits the locks from the omap_prcm driver, no internal locking. * * RETURNS: * Returns 0 on success or a negative error code on failure. */ static int omap4_clk_hsmmc_set_source(struct ti_clock_dev *clkdev, clk_src_t clksrc) { struct omap4_prcm_softc *sc; struct omap4_clk_details* clk_details; struct resource* clk_mem_res; uint32_t clksel; clk_details = omap4_clk_details(clkdev->id); if (clk_details == NULL) return (ENXIO); sc = omap4_prcm_get_instance_softc(clk_details->instance); if (sc == NULL) return ENXIO; clk_mem_res = sc->sc_res; if (clk_mem_res == NULL) return (EINVAL); /* For MMC modules 3, 4 & 5 you can't change the freq, it's always 48MHz */ if ((clkdev->id == MMC3_CLK) || (clkdev->id == MMC4_CLK) || (clkdev->id == MMC5_CLK)) { if (clksrc != F48MHZ_CLK) return (EINVAL); return 0; } clksel = bus_read_4(clk_mem_res, clk_details->clksel_reg); /* Bit 24 is set if 96MHz clock or cleared for 64MHz clock */ if (clksrc == F64MHZ_CLK) clksel &= ~(0x1UL << 24); else if (clksrc == F96MHZ_CLK) clksel |= (0x1UL << 24); else return (EINVAL); bus_write_4(clk_mem_res, clk_details->clksel_reg, clksel); return (0); } /** * omap4_clk_hsmmc_get_source_freq - checks if a module is accessible * @clkdev: pointer to the clockdev structure (id field will contain clock id) * * * * LOCKING: * Inherits the locks from the omap_prcm driver, no internal locking. * * RETURNS: * Returns 0 on success or a negative error code on failure. */ static int omap4_clk_hsmmc_get_source_freq(struct ti_clock_dev *clkdev, unsigned int *freq ) { struct omap4_prcm_softc *sc; struct omap4_clk_details* clk_details; struct resource* clk_mem_res; uint32_t clksel; unsigned int src_freq; clk_details = omap4_clk_details(clkdev->id); if (clk_details == NULL) return (ENXIO); sc = omap4_prcm_get_instance_softc(clk_details->instance); if (sc == NULL) return ENXIO; clk_mem_res = sc->sc_res; if (clk_mem_res == NULL) return (EINVAL); switch (clkdev->id) { case MMC1_CLK: case MMC2_CLK: /* Need to read the CLKSEL field to determine the clock source */ clksel = bus_read_4(clk_mem_res, clk_details->clksel_reg); if (clksel & (0x1UL << 24)) src_freq = FREQ_96MHZ; else src_freq = FREQ_64MHZ; break; case MMC3_CLK: case MMC4_CLK: case MMC5_CLK: src_freq = FREQ_48MHZ; break; default: return (EINVAL); } /* Return the frequency */ if (freq) *freq = src_freq; return (0); } /** * omap4_clk_get_sysclk_freq - gets the sysclk frequency * @sc: pointer to the clk module/device context * * Read the clocking information from the power-control/boot-strap registers, * and stored in two global variables. * * RETURNS: * nothing, values are saved in global variables */ static int omap4_clk_get_sysclk_freq(struct ti_clock_dev *clkdev, unsigned int *freq) { uint32_t clksel; uint32_t sysclk; struct omap4_prcm_softc *sc; sc = omap4_prcm_get_instance_softc(PRM_INSTANCE); if (sc == NULL) return ENXIO; /* Read the input clock freq from the configuration register (CM_SYS_CLKSEL) */ clksel = bus_read_4(sc->sc_res, CM_SYS_CLKSEL_OFFSET); switch (clksel & 0x7) { case 0x1: /* 12Mhz */ sysclk = 12000000; break; case 0x3: /* 16.8Mhz */ sysclk = 16800000; break; case 0x4: /* 19.2Mhz */ sysclk = 19200000; break; case 0x5: /* 26Mhz */ sysclk = 26000000; break; case 0x7: /* 38.4Mhz */ sysclk = 38400000; break; default: panic("%s: Invalid clock freq", __func__); } /* Return the value */ if (freq) *freq = sysclk; return (0); } /** * omap4_clk_get_arm_fclk_freq - gets the MPU clock frequency * @clkdev: ignored * @freq: pointer which upon return will contain the freq in hz * @mem_res: array of allocated memory resources * * Reads the frequency setting information registers and returns the value * in the freq variable. * * RETURNS: * returns 0 on success, a positive error code on failure. */ static int omap4_clk_get_arm_fclk_freq(struct ti_clock_dev *clkdev, unsigned int *freq) { uint32_t clksel; uint32_t pll_mult, pll_div; uint32_t mpuclk, sysclk; struct omap4_prcm_softc *sc; sc = omap4_prcm_get_instance_softc(CM1_INSTANCE); if (sc == NULL) return ENXIO; /* Read the clksel register which contains the DPLL multiple and divide * values. These are applied to the sysclk. */ clksel = bus_read_4(sc->sc_res, CM_CLKSEL_DPLL_MPU); pll_mult = ((clksel >> 8) & 0x7ff); pll_div = (clksel & 0x7f) + 1; /* Get the system clock freq */ omap4_clk_get_sysclk_freq(NULL, &sysclk); /* Calculate the MPU freq */ mpuclk = ((uint64_t)sysclk * pll_mult) / pll_div; /* Return the value */ if (freq) *freq = mpuclk; return (0); } /** * omap4_clk_hsusbhost_activate - activates the USB clocks for the given module * @clkdev: pointer to the clock device structure. * @mem_res: array of memory resources allocated by the top level PRCM driver. * * The USB clocking setup seems to be a bit more tricky than the other modules, * to start with the clocking diagram for the HS host module shows 13 different * clocks. So to try and make it easier to follow the clocking activation * and deactivation is handled in its own set of callbacks. * * LOCKING: * Inherits the locks from the omap_prcm driver, no internal locking. * * RETURNS: * Returns 0 on success or a positive error code on failure. */ struct dpll_param { unsigned int m; unsigned int n; unsigned int m2; unsigned int m3; unsigned int m4; unsigned int m5; unsigned int m6; unsigned int m7; }; /* USB parameters */ struct dpll_param usb_dpll_param[7] = { /* 12M values */ {0x0, 0x0, 0x0, 0x0, 0x0, 0x0, 0x0, 0x0}, /* 13M values */ {0x0, 0x0, 0x0, 0x0, 0x0, 0x0, 0x0, 0x0}, /* 16.8M values */ {0x0, 0x0, 0x0, 0x0, 0x0, 0x0, 0x0, 0x0}, /* 19.2M values */ {0x0, 0x0, 0x0, 0x0, 0x0, 0x0, 0x0, 0x0}, /* 26M values */ {0x0, 0x0, 0x0, 0x0, 0x0, 0x0, 0x0, 0x0}, /* 27M values */ {0x0, 0x0, 0x0, 0x0, 0x0, 0x0, 0x0, 0x0}, /* 38.4M values */ #ifdef CONFIG_OMAP4_SDC {0x32, 0x1, 0x2, 0x0, 0x0, 0x0, 0x0, 0x0}, #else {0x32, 0x1, 0x2, 0x0, 0x0, 0x0, 0x0, 0x0}, #endif }; static int omap4_clk_hsusbhost_activate(struct ti_clock_dev *clkdev) { struct omap4_prcm_softc *sc; struct resource* clk_mem_res; uint32_t clksel_reg_off; uint32_t clksel; unsigned int i; sc = omap4_prcm_get_instance_softc(CM2_INSTANCE); if (sc == NULL) return ENXIO; switch (clkdev->id) { case USBTLL_CLK: /* For the USBTLL module we need to enable the following clocks: * - INIT_L4_ICLK (will be enabled by bootloader) * - TLL_CH0_FCLK * - TLL_CH1_FCLK */ /* We need the CM_L3INIT_HSUSBTLL_CLKCTRL register in CM2 register set */ clk_mem_res = sc->sc_res; clksel_reg_off = L3INIT_CM2_OFFSET + 0x68; /* Enable the module and also enable the optional func clocks for * channels 0 & 1 (is this needed ?) */ clksel = bus_read_4(clk_mem_res, clksel_reg_off); clksel &= ~CLKCTRL_MODULEMODE_MASK; clksel |= CLKCTRL_MODULEMODE_ENABLE; clksel |= (0x1 << 8); /* USB-HOST optional clock: USB_CH0_CLK */ clksel |= (0x1 << 9); /* USB-HOST optional clock: USB_CH1_CLK */ break; case USBHSHOST_CLK: case USBP1_PHY_CLK: case USBP2_PHY_CLK: case USBP1_UTMI_CLK: case USBP2_UTMI_CLK: case USBP1_HSIC_CLK: case USBP2_HSIC_CLK: /* For the USB HS HOST module we need to enable the following clocks: * - INIT_L4_ICLK (will be enabled by bootloader) * - INIT_L3_ICLK (will be enabled by bootloader) * - INIT_48MC_FCLK * - UTMI_ROOT_GFCLK (UTMI only, create a new clock for that ?) * - UTMI_P1_FCLK (UTMI only, create a new clock for that ?) * - UTMI_P2_FCLK (UTMI only, create a new clock for that ?) * - HSIC_P1_60 (HSIC only, create a new clock for that ?) * - HSIC_P1_480 (HSIC only, create a new clock for that ?) * - HSIC_P2_60 (HSIC only, create a new clock for that ?) * - HSIC_P2_480 (HSIC only, create a new clock for that ?) */ /* We need the CM_L3INIT_HSUSBHOST_CLKCTRL register in CM2 register set */ clk_mem_res = sc->sc_res; clksel_reg_off = L3INIT_CM2_OFFSET + 0x58; clksel = bus_read_4(clk_mem_res, clksel_reg_off); /* Enable the module and also enable the optional func clocks */ if (clkdev->id == USBHSHOST_CLK) { clksel &= ~CLKCTRL_MODULEMODE_MASK; clksel |= /*CLKCTRL_MODULEMODE_ENABLE*/2; clksel |= (0x1 << 15); /* USB-HOST clock control: FUNC48MCLK */ } else if (clkdev->id == USBP1_UTMI_CLK) clksel |= (0x1 << 8); /* UTMI_P1_CLK */ else if (clkdev->id == USBP2_UTMI_CLK) clksel |= (0x1 << 9); /* UTMI_P2_CLK */ else if (clkdev->id == USBP1_HSIC_CLK) clksel |= (0x5 << 11); /* HSIC60M_P1_CLK + HSIC480M_P1_CLK */ else if (clkdev->id == USBP2_HSIC_CLK) clksel |= (0x5 << 12); /* HSIC60M_P2_CLK + HSIC480M_P2_CLK */ break; default: return (EINVAL); } bus_write_4(clk_mem_res, clksel_reg_off, clksel); /* Try MAX_MODULE_ENABLE_WAIT number of times to check if enabled */ for (i = 0; i < MAX_MODULE_ENABLE_WAIT; i++) { clksel = bus_read_4(clk_mem_res, clksel_reg_off); if ((clksel & CLKCTRL_IDLEST_MASK) == CLKCTRL_IDLEST_ENABLED) break; } /* Check the enabled state */ if ((clksel & CLKCTRL_IDLEST_MASK) != CLKCTRL_IDLEST_ENABLED) { printf("Error: HERE failed to enable module with clock %d\n", clkdev->id); printf("Error: 0x%08x => 0x%08x\n", clksel_reg_off, clksel); return (ETIMEDOUT); } return (0); } /** * omap4_clk_generic_deactivate - checks if a module is accessible * @clkdev: pointer to the clock device structure. * @mem_res: array of memory resources allocated by the top level PRCM driver. * * * * LOCKING: * Inherits the locks from the omap_prcm driver, no internal locking. * * RETURNS: * Returns 0 on success or a positive error code on failure. */ static int omap4_clk_hsusbhost_deactivate(struct ti_clock_dev *clkdev) { struct omap4_prcm_softc *sc; struct resource* clk_mem_res; uint32_t clksel_reg_off; uint32_t clksel; sc = omap4_prcm_get_instance_softc(CM2_INSTANCE); if (sc == NULL) return ENXIO; switch (clkdev->id) { case USBTLL_CLK: /* We need the CM_L3INIT_HSUSBTLL_CLKCTRL register in CM2 register set */ clk_mem_res = sc->sc_res; clksel_reg_off = L3INIT_CM2_OFFSET + 0x68; clksel = bus_read_4(clk_mem_res, clksel_reg_off); clksel &= ~CLKCTRL_MODULEMODE_MASK; clksel |= CLKCTRL_MODULEMODE_DISABLE; break; case USBHSHOST_CLK: case USBP1_PHY_CLK: case USBP2_PHY_CLK: case USBP1_UTMI_CLK: case USBP2_UTMI_CLK: case USBP1_HSIC_CLK: case USBP2_HSIC_CLK: /* For the USB HS HOST module we need to enable the following clocks: * - INIT_L4_ICLK (will be enabled by bootloader) * - INIT_L3_ICLK (will be enabled by bootloader) * - INIT_48MC_FCLK * - UTMI_ROOT_GFCLK (UTMI only, create a new clock for that ?) * - UTMI_P1_FCLK (UTMI only, create a new clock for that ?) * - UTMI_P2_FCLK (UTMI only, create a new clock for that ?) * - HSIC_P1_60 (HSIC only, create a new clock for that ?) * - HSIC_P1_480 (HSIC only, create a new clock for that ?) * - HSIC_P2_60 (HSIC only, create a new clock for that ?) * - HSIC_P2_480 (HSIC only, create a new clock for that ?) */ /* We need the CM_L3INIT_HSUSBHOST_CLKCTRL register in CM2 register set */ clk_mem_res = sc->sc_res; clksel_reg_off = L3INIT_CM2_OFFSET + 0x58; clksel = bus_read_4(clk_mem_res, clksel_reg_off); /* Enable the module and also enable the optional func clocks */ if (clkdev->id == USBHSHOST_CLK) { clksel &= ~CLKCTRL_MODULEMODE_MASK; clksel |= CLKCTRL_MODULEMODE_DISABLE; clksel &= ~(0x1 << 15); /* USB-HOST clock control: FUNC48MCLK */ } else if (clkdev->id == USBP1_UTMI_CLK) clksel &= ~(0x1 << 8); /* UTMI_P1_CLK */ else if (clkdev->id == USBP2_UTMI_CLK) clksel &= ~(0x1 << 9); /* UTMI_P2_CLK */ else if (clkdev->id == USBP1_HSIC_CLK) clksel &= ~(0x5 << 11); /* HSIC60M_P1_CLK + HSIC480M_P1_CLK */ else if (clkdev->id == USBP2_HSIC_CLK) clksel &= ~(0x5 << 12); /* HSIC60M_P2_CLK + HSIC480M_P2_CLK */ break; default: return (EINVAL); } bus_write_4(clk_mem_res, clksel_reg_off, clksel); return (0); } /** * omap4_clk_hsusbhost_accessible - checks if a module is accessible * @clkdev: pointer to the clock device structure. * @mem_res: array of memory resources allocated by the top level PRCM driver. * * * * LOCKING: * Inherits the locks from the omap_prcm driver, no internal locking. * * RETURNS: * Returns 0 if module is not enable, 1 if module is enabled or a negative * error code on failure. */ static int omap4_clk_hsusbhost_accessible(struct ti_clock_dev *clkdev) { struct omap4_prcm_softc *sc; struct resource* clk_mem_res; uint32_t clksel_reg_off; uint32_t clksel; sc = omap4_prcm_get_instance_softc(CM2_INSTANCE); if (sc == NULL) return ENXIO; if (clkdev->id == USBTLL_CLK) { /* We need the CM_L3INIT_HSUSBTLL_CLKCTRL register in CM2 register set */ clk_mem_res = sc->sc_res; clksel_reg_off = L3INIT_CM2_OFFSET + 0x68; } else if (clkdev->id == USBHSHOST_CLK) { /* We need the CM_L3INIT_HSUSBHOST_CLKCTRL register in CM2 register set */ clk_mem_res = sc->sc_res; clksel_reg_off = L3INIT_CM2_OFFSET + 0x58; } else { return (EINVAL); } clksel = bus_read_4(clk_mem_res, clksel_reg_off); /* Check the enabled state */ if ((clksel & CLKCTRL_IDLEST_MASK) != CLKCTRL_IDLEST_ENABLED) return (0); return (1); } /** * omap4_clk_hsusbhost_set_source - sets the source clocks * @clkdev: pointer to the clock device structure. * @clksrc: the clock source ID for the given clock. * @mem_res: array of memory resources allocated by the top level PRCM driver. * * * * LOCKING: * Inherits the locks from the omap_prcm driver, no internal locking. * * RETURNS: * Returns 0 if successful otherwise a negative error code on failure. */ static int omap4_clk_hsusbhost_set_source(struct ti_clock_dev *clkdev, clk_src_t clksrc) { struct omap4_prcm_softc *sc; struct resource* clk_mem_res; uint32_t clksel_reg_off; uint32_t clksel; unsigned int bit; sc = omap4_prcm_get_instance_softc(CM2_INSTANCE); if (sc == NULL) return ENXIO; if (clkdev->id == USBP1_PHY_CLK) bit = 24; else if (clkdev->id != USBP2_PHY_CLK) bit = 25; else return (EINVAL); /* We need the CM_L3INIT_HSUSBHOST_CLKCTRL register in CM2 register set */ clk_mem_res = sc->sc_res; clksel_reg_off = L3INIT_CM2_OFFSET + 0x58; clksel = bus_read_4(clk_mem_res, clksel_reg_off); /* Set the clock source to either external or internal */ if (clksrc == EXT_CLK) clksel |= (0x1 << bit); else clksel &= ~(0x1 << bit); bus_write_4(clk_mem_res, clksel_reg_off, clksel); return (0); } #define PRM_RSTCTRL 0x1b00 #define PRM_RSTCTRL_RESET 0x2 static void omap4_prcm_reset(void) { struct omap4_prcm_softc *sc; sc = omap4_prcm_get_instance_softc(PRM_INSTANCE); if (sc == NULL) return; bus_write_4(sc->sc_res, PRM_RSTCTRL, bus_read_4(sc->sc_res, PRM_RSTCTRL) | PRM_RSTCTRL_RESET); bus_read_4(sc->sc_res, PRM_RSTCTRL); } /** * omap4_prcm_probe - probe function for the driver * @dev: prcm device handle * * Simply sets the name of the driver module. * * LOCKING: * None * * RETURNS: * Always returns 0 */ static int omap4_prcm_probe(device_t dev) { const struct ofw_compat_data *ocd; if (!ofw_bus_status_okay(dev)) return (ENXIO); ocd = ofw_bus_search_compatible(dev, compat_data); if ((int)ocd->ocd_data == 0) return (ENXIO); switch ((int)ocd->ocd_data) { case PRM_INSTANCE: device_set_desc(dev, "TI OMAP Power, Reset and Clock Management (PRM)"); break; case CM1_INSTANCE: device_set_desc(dev, "TI OMAP Power, Reset and Clock Management (C1)"); break; case CM2_INSTANCE: device_set_desc(dev, "TI OMAP Power, Reset and Clock Management (C2)"); break; default: device_printf(dev, "unknown instance type: %d\n", (int)ocd->ocd_data); return (ENXIO); } return (BUS_PROBE_DEFAULT); } /** * omap_prcm_attach - attach function for the driver * @dev: prcm device handle * * Allocates and sets up the driver context, this simply entails creating a * bus mappings for the PRCM register set. * * LOCKING: * None * * RETURNS: * Always returns 0 */ extern uint32_t platform_arm_tmr_freq; static int omap4_prcm_attach(device_t dev) { struct omap4_prcm_softc *sc; const struct ofw_compat_data *ocd; sc = device_get_softc(dev); ocd = ofw_bus_search_compatible(dev, compat_data); sc->sc_instance = (int)ocd->ocd_data; sc->sc_res = bus_alloc_resource_any(dev, SYS_RES_MEMORY, &sc->sc_rid, RF_ACTIVE); if (sc->sc_res == NULL) { device_printf(dev, "could not allocate resources\n"); return (ENXIO); } ti_cpu_reset = omap4_prcm_reset; return (0); } static void omap4_prcm_new_pass(device_t dev) { struct omap4_prcm_softc *sc = device_get_softc(dev); unsigned int freq; if (sc->attach_done || bus_get_pass() < (BUS_PASS_TIMER + BUS_PASS_ORDER_EARLY)) { bus_generic_new_pass(dev); return; } sc->attach_done = 1; /* * In order to determine ARM frequency we need both RPM and CM1 * instances up and running. So wait until all CRM devices are * initialized. Should be replaced with proper clock framework */ if (device_get_unit(dev) == 2) { omap4_clk_get_arm_fclk_freq(NULL, &freq); arm_tmr_change_frequency(freq / 2); } return; } static device_method_t omap4_prcm_methods[] = { DEVMETHOD(device_probe, omap4_prcm_probe), DEVMETHOD(device_attach, omap4_prcm_attach), /* Bus interface */ DEVMETHOD(bus_new_pass, omap4_prcm_new_pass), {0, 0}, }; static driver_t omap4_prcm_driver = { "omap4_prcm", omap4_prcm_methods, sizeof(struct omap4_prcm_softc), }; EARLY_DRIVER_MODULE(omap4_prcm, simplebus, omap4_prcm_driver, 0, 0, BUS_PASS_BUS + BUS_PASS_ORDER_MIDDLE); MODULE_VERSION(omap4_prcm, 1);