.\" Copyright (c) 2006-2008 Joel Dahl .\" Copyright (c) 2008 Alexander Motin .\" All rights reserved. .\" .\" Redistribution and use in source and binary forms, with or without .\" modification, are permitted provided that the following conditions .\" are met: .\" 1. Redistributions of source code must retain the above copyright .\" notice, this list of conditions and the following disclaimer. .\" 2. Redistributions in binary form must reproduce the above copyright .\" notice, this list of conditions and the following disclaimer in the .\" documentation and/or other materials provided with the distribution. .\" .\" THIS SOFTWARE IS PROVIDED BY THE AUTHOR AND CONTRIBUTORS ``AS IS'' AND .\" ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE .\" IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE .\" ARE DISCLAIMED. IN NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE .\" FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL .\" DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS .\" OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) .\" HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT .\" LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY .\" OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF .\" SUCH DAMAGE. .\" .\" $FreeBSD$ .\" .Dd January 11, 2012 .Dt SND_HDA 4 .Os .Sh NAME .Nm snd_hda .Nd "Intel High Definition Audio bridge device driver" .Sh SYNOPSIS To compile this driver into the kernel, place the following lines in your kernel configuration file: .Bd -ragged -offset indent .Cd "device sound" .Cd "device snd_hda" .Ed .Pp Alternatively, to load the driver as a module at boot time, place the following line in .Xr loader.conf 5 : .Bd -literal -offset indent snd_hda_load="YES" .Ed .Sh DESCRIPTION The High Definition (HD) Audio specification was developed by Intel as the logical successor of the old AC'97 specification and has several advantages, such as higher bandwidth which allows more channels and more detailed formats, support for several logical audio devices, and general purpose DMA channels. .Pp The .Nm driver includes HDA bus controller driver (hdac), HDA codec driver (hdacc) and HDA codecs audio functions bridge driver (hdaa) that allows the generic audio driver, .Xr sound 4 , to be used with this hardware. Only audio functions are supported by .Nm . Modem and other possible functions are not implemented. .Pp The .Nm driver supports hardware that conforms with revision 1.0 of the Intel High Definition Audio specification and tries to behave much like the Microsoft Universal Audio Architecture (UAA) draft (revision 0.7b) for handling audio devices. .Pp According to HDA and UAA specifications, depending on the number of HDA buses and codecs present in system, their audio capabilities and BIOS provided configuration, the .Nm driver often provides several PCM audio devices. For example, one device for main rear 7.1 output and inputs, one device for independent headset connectors at front and one device for SPDIF or HDMI audio input/output. The assignment of audio inputs and outputs may be tuned with .Xr device.hints 5 or .Xr sysctl 8 . The driver's verbose boot messages provide a lot of information about the operation of the driver and present audio setup. .Pp The default audio device may be tuned by setting the .Ar hw.snd.default_unit sysctl, as described in .Xr sound 4 , or explicitly specified in application settings. .Ss Boot-time Configuration The following variables are available at boot-time through the .Xr device.hints 5 file: .Bl -tag -width ".Va hint.hdac.%d.config"-offset indent .It Va hint.hdac.%d.config Configures a range of possible controller options. Possible values are: .Dq Li 64bit , .Dq Li dmapos , .Dq Li msi . An option prefixed with .Dq Li no , such as .Dq Li nomsi , will do the opposite and takes precedence. Options can be separated by whitespace and commas. .It Va hint.hdac.%d.msi Controls MSI (Message Signaled Interrupts) support. .It Va hint.hdac.%d.cad%d.nid%d.config Same as .Va hint.hdaa.%d.nid%d.config .It Va hint.hdaa.%d.config Configures a range of possible audio function options. Possible values are: .Dq Li eapdinv , .Dq Li ivref , .Dq Li ivref50 , .Dq Li ivref80 , .Dq Li ivref100 , .Dq Li fixedrate , .Dq Li forcestereo , .Dq Li ovref , .Dq Li ovref50 , .Dq Li ovref80 , .Dq Li ovref100 , .Dq Li senseinv , .Dq Li softpcmvol , and .Dq Li vref . An option prefixed with .Dq Li no , such as .Dq Li nofixedrate , will do the opposite and takes precedence. Options can be separated by whitespace and commas. .Pp The .Dq Li eapdinv option inverts External Amplifier Power Down signal. The .Dq Li fixedrate denies all sampling rates except 48KHz. The .Dq Li forcestereo denies mono playback/recording. The .Dq Li senseinv option inverts jack sensing logic. The .Dq Li ivref Ns Ar X and .Dq Li ovref Ns Ar X options control the voltage used to power external microphones. .It Va hint.hdaa.%d.gpio_config Overrides audio function GPIO pins configuration set by BIOS. May be specified as a set of space-separated .Dq Ar num Ns = Ns Ar value pairs, where .Ar num is GPIO line number, and .Ar value is one of: .Dq Li keep , .Dq Li set , .Dq Li clear , .Dq Li disable and .Dq Li input . .Pp .Dq Li GPIO Ns s are a codec's General Purpose I/O pins which system integrators sometimes use to control external muters, amplifiers and so on. If you have no sound, or sound volume is not adequate, you may have to experiment a bit with the GPIO setup to find the optimal setup for your system. .It Va hint.hdaa.%d.nid%d.config Overrides audio function pin configuration set by BIOS. May be specified as a 32-bit hexadecimal value with a leading .Dq 0x , or as a set of space-separated .Dq Ar option Ns = Ns Ar value pairs. .El .Pp Pin configuration is the UAA driver's main source of information about codec usage. This information is usually provided by the codec manufacturer and tuned by system integrators for specific system requirements. The .Nm driver allows users to override it to fix integrator mistakes or to use the available codec in alternative ways (for example to get stereo output and 2 inputs instead of a single 5.1 output). .Pp The following options are supported: .Bl -tag -width ".Va device=" -offset indent .It Va as Association number. Associations are used to group individual pins to form a complex multi-pin device. For example, to group 4 connectors for 7.1 input/output, or to treat several input connectors as sources for the same input device. Association numbers can be specified as numeric values from 0 to 15. A value of 0 means disabled pin. A value of 15 is a set of independent unassociated pins. Each association includes only pins of the same direction (in/out) and is detected atomically (all pins or none). A separate PCM audio device is created for every pair of input and output associations. .It Va seq Sequence number. A unique, per-association number used to order pins inside the particular association. Sequence numbers can be specified as numeric values from 0 to 15. .Pp The sequence number 15 has a special meaning for output associations. Output pins with this number and device type .Dq Ar Headphones will duplicate (with automatic mute if jack detection is supported) the first pin in that association. .Pp The sequence numbers 14 and 15 has a special meaning for input associations. Their presence in association defines it as multiplexed or mixed respectively. If none of them present and there are more then one pin in association, the association will provide multichannel input. .Pp For multichannel input/output assotiations sequence numbers encode channel pairs positions: 0 - Front, 1 - Center/LFE, 2 - Back, 3 - Front Wide Center, 4 - Side. Standard combinations are: (0) - Stereo; (0, 2), (0, 4) - Quadro; (0, 1, 2), (0, 1, 4) - 5.1; (0, 1, 2, 4) - 7.1. .It Va device Device type. Can be specified as a number from 0 to 15 or as a name: .Dq Li Line-out , .Dq Li Speaker , .Dq Li Headphones, .Dq Li CD , .Dq Li SPDIF-out , .Dq Li Digital-out , .Dq Li Modem-line , .Dq Li Modem-handset , .Dq Li Line-in , .Dq Li AUX , .Dq Li Mic , .Dq Li Telephony , .Dq Li SPDIF-in , .Dq Li Digital-in , .Dq Li Res.E , or .Dq Li Other . The device type also describes the pin direction (in/out). For example, .Dq Li CD always means an input pin, while .Dq Li Headphones always means an output. .It Va conn Connection type. Can be specified as a number from 0 to 3. The connection type can also be specified as one of the special names .Dq Li Jack , .Dq Li None , .Dq Li Fixed , or .Dq Li Both . Pins with a connection type of .Dq Li None are disabled. .It Va ctype Connector physical type. Can be specified as a number from 0 to 15. This is a reference only value. It is ignored by the .Nm driver. .It Va color Connector color. Can be specified as a number from 0 to 15 or as one of the names .Dq Li Unknown , .Dq Li Black , .Dq Li Grey , .Dq Li Blue , .Dq Li Green , .Dq Li Red , .Dq Li Orange , .Dq Li Yellow , .Dq Li Purple , .Dq Li Pink , .Dq Li Res.A , .Dq Li Res.B , .Dq Li Res.C , .Dq Li Res.D , .Dq Li White , or .Dq Li Other . This is a reference only value. It is ignored by the .Nm driver. .It Va loc Connector physical location. Can be specified as a number from 0 to 63. This is a reference only value. It is ignored by the .Nm driver. .It Va misc Misc bits. Can be specified as a number from 0 to 15. Bit 0 has a special meaning. When set it means that jack detection is not implemented in hardware. .El .Ss Runtime Configuration The following .Xr sysctl 8 variables are available in addition to those available to all .Xr sound 4 devices: .Bl -tag -width ".Va dev.hdaa.%d.nid%d_original" -offset indent .It Va dev.hdac.%d.pindump Setting this to a non-zero value dumps the current pin configuration, main capabilities and jack sense status of all audio functions on the controller to console and syslog. .It Va dev.hdac.%d.polling Enables polling mode. In this mode the driver operates by querying the device state on timer ticks using .Xr callout 9 instead of interrupts. Polling is disabled by default. Do not enable it unless you are facing weird interrupt problems or if the device cannot generate interrupts at all. .It Va dev.hdaa.%d.config Run-time equivalent of the .Va hint.hdaa.%d.config tunable. .It Va dev.hdaa.%d.gpi_state Current state of GPI lines. .It Va dev.hdaa.%d.gpio_state Current state of GPIO lines. .It Va dev.hdaa.%d.gpio_config Run-time equivalent of the .Va hint.hdaa.%d.gpio.config tunable. .It Va dev.hdaa.%d.gpo_state Current state of GPO lines. .It Va dev.hdaa.%d.nid%d_config Run-time equivalent of the .Va hint.hdaa.%d.nid%d.config tunable. .It Va dev.hdaa.%d.nid%d_original Original pin configuration written by BIOS. .It Va dev.hdaa.%d.reconfig Setting this to a non-zero value makes driver to destroy existing pcm devices and process new pins configuration set via .Va dev.hdaa.%d.nid%d_config. .El .Sh EXAMPLES Taking HP Compaq DX2300 with Realtek ALC888 HDA codec for example. This system has two audio connectors on a front side, three audio connectors on a rear side and one internal speaker. According to verbose driver output and the codec datasheet, this codec has five stereo DACs and two stereo ADCs, all of them are routable to any codec pin (external connector). All codec pins are reversible (could be configured either as input or output). .Pp So high codec uniformity and flexibility allow driver to configure it in many different ways, depending on requested pins usage described by pins configuration. The driver reports such default pin configuration when verbose messages enabled: .Bd -literal hdaa0: nid 0x as seq device conn jack loc color misc hdaa0: 20 01014020 2 0 Line-out Jack 1/8 Rear Green 0 hdaa0: 21 99130110 1 0 Speaker Fixed ATAPI Onboard Unknown 1 hdaa0: 22 411111f0 15 0 Speaker None 1/8 Rear Black 1 DISA hdaa0: 23 411111f0 15 0 Speaker None 1/8 Rear Black 1 DISA hdaa0: 24 01a19830 3 0 Mic Jack 1/8 Rear Pink 8 hdaa0: 25 02a1983f 3 15 Mic Jack 1/8 Front Pink 8 hdaa0: 26 01813031 3 1 Line-in Jack 1/8 Rear Blue 0 hdaa0: 27 0221401f 1 15 Headphones Jack 1/8 Front Green 0 hdaa0: 28 411111f0 15 0 Speaker None 1/8 Rear Black 1 DISA hdaa0: 30 411111f0 15 0 Speaker None 1/8 Rear Black 1 DISA hdaa0: 31 411111f0 15 0 Speaker None 1/8 Rear Black 1 DISA .Ed .Pp Here we can see, that the nodes with ID (nid) 25 and 27 are front panel connectors (Jack, Front), nids 20, 24 and 26 are rear panel connectors (Jack, Rear) and nid 21 is a built-in speaker (Fixed, Onboard). Pins with nids 22, 23, 28, 30 and 31 will be disabled by driver due to "None" connectivity. So the pin count and description matches to connectors that we have. .Pp Using association (as) and sequence (seq) fields values pins are grouped into 3 associations: .Bd -literal hdaa0: Association 0 (1) out: hdaa0: Pin nid=21 seq=0 hdaa0: Pin nid=27 seq=15 hdaa0: Association 1 (2) out: hdaa0: Pin nid=20 seq=0 hdaa0: Association 2 (3) in: hdaa0: Pin nid=24 seq=0 hdaa0: Pin nid=26 seq=1 hdaa0: Pin nid=25 seq=15 .Ed .Pp Each .Xr pcm 4 device uses two associations: one for playback and one for recording. Associations processed and assigned to .Xr pcm 4 devices in increasing numerical order. In this case association #0 (1) will become .Li pcm0 device playback, using the internal speakers and .Ar Headphones jack with speaker automute on the headphones jack connection. Association #1 (2) will become .Li pcm1 playback, using the .Ar Line-out jack. Association #2 (3) will become .Li pcm0 recording, using the external microphones and the .Ar Line-in jack. .Pp The .Nm driver provides extensive verbose messages to diagnose its operation logic and describe its current codec configuration. .Pp Using .Xr device.hints 5 it is possible to modify the configuration of the existing pins, allowing a broad range of different audio setups. Here are a few examples of some setups possible for this particular hardware: .Ss Example 1 Setting the .Xr device.hints 5 options .Bd -literal hint.hdac.0.cad0.nid20.config="as=1" hint.hdac.0.cad0.nid21.config="as=2" .Ed .Pp will swap line-out and speaker functions. So the .Li pcm0 device will play to the line-out and headphones jacks. Line-out will be muted on the headphones jack connection. Recording on .Li pcm0 will go from two external microphones and line-in jacks. .Li pcm1 playback will go to the internal speaker. .Pp .Ss Example 2 Setting the .Xr device.hints 5 options .Bd -literal hint.hdac.0.cad0.nid20.config="as=1 seq=15 device=Headphones" hint.hdac.0.cad0.nid27.config="as=2 seq=0" hint.hdac.0.cad0.nid25.config="as=4 seq=0" .Ed .Pp will split the headphones and one of the microphones to a separate device. The .Li pcm0 device will play to the internal speaker and to the line-out jack, with speaker automute on the line-out jack connection. Recording on .Li pcm0 will use input from one external microphone and the line-in jacks. The .Li pcm1 device will be completely dedicated to a headset (headphones and mic) connected to the front connectors. .Pp .Ss Example 3 Setting the .Xr device.hints 5 options .Bd -literal hint.hdac.0.cad0.nid20.config="as=1 seq=0" hint.hdac.0.cad0.nid26.config="as=2 seq=0" hint.hdac.0.cad0.nid27.config="as=3 seq=0" hint.hdac.0.cad0.nid25.config="as=4 seq=0" hint.hdac.0.cad0.nid24.config="as=5 seq=0 device=Line-out" hint.hdac.0.cad0.nid21.config="as=6 seq=0" .Ed .Pp will give 4 independent devices: .Li pcm0 .Pq line-out and line-in , .Li pcm1 .Pq headphones and mic , .Li pcm2 .Pq additional line-out via retasked rear mic jack , and .Li pcm3 .Pq internal speaker . .Pp .Ss Example 4 Setting the .Xr device.hints 5 options .Bd -literal hint.hdac.0.cad0.nid20.config="as=1 seq=0" hint.hdac.0.cad0.nid24.config="as=1 seq=1 device=Line-out" hint.hdac.0.cad0.nid26.config="as=1 seq=2 device=Line-out" hint.hdac.0.cad0.nid21.config="as=2 seq=0" .Ed .Pp will give 2 devices: .Li pcm0 for 5.1 playback via 3 rear connectors (line-out and retasked mic and line-in) and headset (headphones and mic) at front connectors. .Li pcm1 for internal speaker playback. On headphones connection rear connectors will be muted. .Sh MIXER CONTROLS Depending on codec configuration, these controls and signal sources could be reported to .Xr sound 4 : .Bl -tag -width ".Va speaker" -offset indent .It Va vol overall output level (volume) .It Va rec overall recording level .It Va igain input-to-output monitoring loopback level .It Va ogain external amplifier control .It Va pcm PCM playback .It Va mix input mix .It Va mic first external or second internal microphone input .It Va monitor first internal or second external microphone input .It Va line , Va line1 , Va line2, Va line3 analog (line) inputs .It Va dig1 , Va dig2 , Va dig3 digital (S/PDIF, HDMI or DisplayPort) inputs .It Va cd CD input .It Va speaker PC speaker input .It Va phin , Va phout , Va radio . Va video other random inputs .El .Pp Controls have different precision. Some could be just an on/off triggers. Most of controls use logarithmic scale. .Sh HARDWARE The .Nm driver supports controllers having PCI class 4 (multimedia) and subclass 3 (HDA), compatible with Intel HDA specification. .Pp The .Nm driver supports more then two hundred different controllers and CODECs. There is no sense to list all of them here, as in most cases specific CODEC configuration and wiring are more important then type of the CODEC itself. .Sh SEE ALSO .Xr sound 4 , .Xr snd_ich 4 , .Xr device.hints 5 , .Xr loader.conf 5 , .Xr sysctl 8 .Sh HISTORY The .Nm device driver first appeared in .Fx 6.3 . .Sh AUTHORS .An -nosplit The .Nm driver was written by .An Stephane E. Potvin Aq sepotvin@videotron.ca , .An Ariff Abdullah Aq ariff@FreeBSD.org and .An Alexander Motin Aq mav@FreeBSD.org . This manual page was written by .An Joel Dahl Aq joel@FreeBSD.org , .An Alexander Motin Aq mav@FreeBSD.org and .An Giorgos Keramidas Aq keramida@FreeBSD.org . .Sh BUGS Some Hardware/OEM vendors tend to screw up BIOS settings or use custom unusual CODEC wiring that create problems to the driver. This may result in missing pcm devices, or a state where the .Nm driver seems to attach and work, but no sound is played. Some cases can be solved by tuning .Pa loader.conf variables. But before trying to fix problem that way, make sure that there really is a problem and that the PCM audio device in use really corresponds to the expected audio connector. .Pp Some vendors use non-standardized General Purpose I/O (GPIO) pins of the codec to control external amplifiers. In some cases setting a combination of GPIO bits may be needed to make sound work on a specific device. .Pp HDMI and DisplayPort audio may also require support from video driver.