.\" Copyright (c) 2001 Wind River Systems .\" Copyright (c) 1997, 1998, 1999, 2000, 2001 .\" Bill Paul . All rights reserved. .\" .\" Redistribution and use in source and binary forms, with or without .\" modification, are permitted provided that the following conditions .\" are met: .\" 1. Redistributions of source code must retain the above copyright .\" notice, this list of conditions and the following disclaimer. .\" 2. Redistributions in binary form must reproduce the above copyright .\" notice, this list of conditions and the following disclaimer in the .\" documentation and/or other materials provided with the distribution. .\" 3. All advertising materials mentioning features or use of this software .\" must display the following acknowledgement: .\" This product includes software developed by Bill Paul. .\" 4. Neither the name of the author nor the names of any co-contributors .\" may be used to endorse or promote products derived from this software .\" without specific prior written permission. .\" .\" THIS SOFTWARE IS PROVIDED BY Bill Paul AND CONTRIBUTORS ``AS IS'' AND .\" ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE .\" IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE .\" ARE DISCLAIMED. IN NO EVENT SHALL Bill Paul OR THE VOICES IN HIS HEAD .\" BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR .\" CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF .\" SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS .\" INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN .\" CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) .\" ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF .\" THE POSSIBILITY OF SUCH DAMAGE. .\" .\" $FreeBSD$ .\" .Dd September 23, 2006 .Dt BGE 4 .Os .Sh NAME .Nm bge .Nd "Broadcom BCM570x/5714/5721/5750/5751/5752/5789 PCI Gigabit Ethernet adapter driver" .Sh SYNOPSIS To compile this driver into the kernel, place the following lines in your kernel configuration file: .Bd -ragged -offset indent .Cd "device miibus" .Cd "device bge" .Ed .Pp Alternatively, to load the driver as a module at boot time, place the following line in .Xr loader.conf 5 : .Bd -literal -offset indent if_bge_load="YES" .Ed .Sh DESCRIPTION The .Nm driver provides support for various NICs based on the Broadcom BCM570x, 5714, 5721, 5750, 5751, 5752 and 5789 families of Gigabit Ethernet controller chips. .Pp All of these NICs are capable of 10, 100 and 1000Mbps speeds over CAT5 copper cable, except for the SysKonnect SK-9D41 which supports only 1000Mbps over multimode fiber. The BCM570x builds upon the technology of the Alteon Tigon II. It has two R4000 CPU cores and is PCI v2.2 and PCI-X v1.0 compliant. It supports IP, TCP and UDP checksum offload for both receive and transmit, multiple RX and TX DMA rings for QoS applications, rules-based receive filtering, and VLAN tag stripping/insertion as well as a 256-bit multicast hash filter. Additional features may be provided via value-add firmware updates. The BCM570x supports TBI (ten bit interface) and GMII transceivers, which means it can be used with either copper or 1000baseX fiber applications. Note however the device only supports a single speed in TBI mode. .Pp Most BCM5700-based cards also use the Broadcom BCM5401 or BCM5411 10/100/1000 copper gigabit transceivers, which support autonegotiation of 10, 100 and 1000Mbps modes in full or half duplex. .Pp The BCM5700, BCM5701, BCM5703, BCM5704, BCM5714 and BCM5780 also support jumbo frames, which can be configured via the interface MTU setting. Selecting an MTU larger than 1500 bytes with the .Xr ifconfig 8 utility configures the adapter to receive and transmit jumbo frames. Using jumbo frames can greatly improve performance for certain tasks, such as file transfers and data streaming. .Pp The .Nm driver supports the following media types: .Bl -tag -width ".Cm 10baseT/UTP" .It Cm autoselect Enable autoselection of the media type and options. The user can manually override the autoselected mode by adding media options to .Xr rc.conf 5 . .It Cm 10baseT/UTP Set 10Mbps operation. The .Xr ifconfig 8 .Ic mediaopt option can also be used to select either .Cm full-duplex or .Cm half-duplex modes. .It Cm 100baseTX Set 100Mbps (Fast Ethernet) operation. The .Xr ifconfig 8 .Ic mediaopt option can also be used to select either .Cm full-duplex or .Cm half-duplex modes. .It Cm 1000baseTX Set 1000baseTX operation over twisted pair. Only .Cm full-duplex mode is supported. .It Cm 1000baseSX Set 1000Mbps (Gigabit Ethernet) operation. Both .Cm full-duplex and .Cm half-duplex modes are supported. .El .Pp The .Nm driver supports the following media options: .Bl -tag -width ".Cm full-duplex" .It Cm full-duplex Force full duplex operation. .It Cm half-duplex Force half duplex operation. .El .Pp The .Nm driver also supports one special link option for 1000baseTX cards: .Bl -tag -width ".Cm link0" .It Cm link0 With 1000baseTX cards, establishing a link between two ports requires that one port be configured as a master and the other a slave. With autonegotiation, the master/slave settings will be chosen automatically. However when manually selecting the link state, it is necessary to force one side of the link to be a master and the other a slave. The .Nm driver configures the ports as slaves by default. Setting the .Cm link0 flag with .Xr ifconfig 8 will set a port as a master instead. .El .Pp For more information on configuring this device, see .Xr ifconfig 8 . .Sh HARDWARE The .Nm driver provides support for various NICs based on the Broadcom BCM570x family of Gigabit Ethernet controller chips, including the following: .Pp .Bl -bullet -compact .It 3Com 3c996-T (10/100/1000baseTX) .It Dell PowerEdge 1750 integrated BCM5704C NIC (10/100/1000baseTX) .It Dell PowerEdge 2550 integrated BCM5700 NIC (10/100/1000baseTX) .It Dell PowerEdge 2650 integrated BCM5703 NIC (10/100/1000baseTX) .It IBM x235 server integrated BCM5703x NIC (10/100/1000baseTX) .It HP Compaq dc7600 integrated BCM5752 NIC (10/100/1000baseTX) .It HP ProLiant NC7760 embedded Gigabit NIC (10/100/1000baseTX) .It HP ProLiant NC7770 PCI-X Gigabit NIC (10/100/1000baseTX) .It HP ProLiant NC7771 PCI-X Gigabit NIC (10/100/1000baseTX) .It HP ProLiant NC7781 embedded PCI-X Gigabit NIC (10/100/1000baseTX) .It Netgear GA302T (10/100/1000baseTX) .It SysKonnect SK-9D21 (10/100/1000baseTX) .It SysKonnect SK-9D41 (1000baseSX) .El .Sh LOADER TUNABLES Tunables can be set at the .Xr loader 8 prompt before booting the kernel, or stored in .Xr loader.conf 5 . .Bl -tag -width indent .It Va hw.bge.fake_autoneg Set to 1 for special handling of the BCM5704 HW. Disabled by default. .It Va hw.bge.allow_asf Allow the ASF feature for cooperating with IPMI. Can cause system lockup problems on a small number of systems. Enabled by default. .El .Sh DIAGNOSTICS .Bl -diag .It "bge%d: couldn't map memory" A fatal initialization error has occurred. .It "bge%d: couldn't map ports" A fatal initialization error has occurred. .It "bge%d: couldn't map interrupt" A fatal initialization error has occurred. .It "bge%d: no memory for softc struct!" The driver failed to allocate memory for per-device instance information during initialization. .It "bge%d: failed to enable memory mapping!" The driver failed to initialize PCI shared memory mapping. This might happen if the card is not in a bus-master slot. .It "bge%d: no memory for jumbo buffers!" The driver failed to allocate memory for jumbo frames during initialization. .It "bge%d: watchdog timeout" The device has stopped responding to the network, or there is a problem with the network connection (cable). .El .Sh SEE ALSO .Xr altq 4 , .Xr arp 4 , .Xr miibus 4 , .Xr netintro 4 , .Xr ng_ether 4 , .Xr polling 4 , .Xr vlan 4 , .Xr ifconfig 8 .Sh HISTORY The .Nm device driver first appeared in .Fx 4.5 . .Sh AUTHORS The .Nm driver was written by .An Bill Paul Aq wpaul@windriver.com .