/* * refclock_pst - clock driver for PSTI/Traconex WWV/WWVH receivers */ #ifdef HAVE_CONFIG_H #include #endif #if defined(REFCLOCK) && defined(CLOCK_PST) #include "ntpd.h" #include "ntp_io.h" #include "ntp_refclock.h" #include "ntp_stdlib.h" #include #include /* * This driver supports the PSTI 1010 and Traconex 1020 WWV/WWVH * Receivers. No specific claim of accuracy is made for these receiver, * but actual experience suggests that 10 ms would be a conservative * assumption. * * The DIPswitches should be set for 9600 bps line speed, 24-hour day- * of-year format and UTC time zone. Automatic correction for DST should * be disabled. It is very important that the year be set correctly in * the DIPswitches; otherwise, the day of year will be incorrect after * 28 April of a normal or leap year. The propagation delay DIPswitches * should be set according to the distance from the transmitter for both * WWV and WWVH, as described in the instructions. While the delay can * be set only to within 11 ms, the fudge time1 parameter can be used * for vernier corrections. * * Using the poll sequence QTQDQM, the response timecode is in three * sections totalling 50 ASCII printing characters, as concatenated by * the driver, in the following format: * * ahh:mm:ss.fffs yy/dd/mm/ddd frdzycchhSSFTttttuuxx * * on-time = first * hh:mm:ss.fff = hours, minutes, seconds, milliseconds * a = AM/PM indicator (' ' for 24-hour mode) * yy = year (from internal switches) * dd/mm/ddd = day of month, month, day of year * s = daylight-saving indicator (' ' for 24-hour mode) * f = frequency enable (O = all frequencies enabled) * r = baud rate (3 = 1200, 6 = 9600) * d = features indicator (@ = month/day display enabled) * z = time zone (0 = UTC) * y = year (5 = 91) * cc = WWV propagation delay (52 = 22 ms) * hh = WWVH propagation delay (81 = 33 ms) * SS = status (80 or 82 = operating correctly) * F = current receive frequency (4 = 15 MHz) * T = transmitter (C = WWV, H = WWVH) * tttt = time since last update (0000 = minutes) * uu = flush character (03 = ^c) * xx = 94 (unknown) * * The alarm condition is indicated by other than '8' at A, which occurs * during initial synchronization and when received signal is lost for * an extended period; unlock condition is indicated by other than * "0000" in the tttt subfield at Q. * * Fudge Factors * * There are no special fudge factors other than the generic. */ /* * Interface definitions */ #define DEVICE "/dev/wwv%d" /* device name and unit */ #define SPEED232 B9600 /* uart speed (9600 baud) */ #define PRECISION (-10) /* precision assumed (about 1 ms) */ #define WWVREFID "WWV\0" /* WWV reference ID */ #define WWVHREFID "WWVH" /* WWVH reference ID */ #define DESCRIPTION "PSTI/Traconex WWV/WWVH Receiver" /* WRU */ #define PST_PHI (10e-6) /* max clock oscillator offset */ #define LENPST 46 /* min timecode length */ /* * Unit control structure */ struct pstunit { int tcswitch; /* timecode switch */ char *lastptr; /* pointer to timecode data */ }; /* * Function prototypes */ static int pst_start (int, struct peer *); static void pst_shutdown (int, struct peer *); static void pst_receive (struct recvbuf *); static void pst_poll (int, struct peer *); /* * Transfer vector */ struct refclock refclock_pst = { pst_start, /* start up driver */ pst_shutdown, /* shut down driver */ pst_poll, /* transmit poll message */ noentry, /* not used (old pst_control) */ noentry, /* initialize driver */ noentry, /* not used (old pst_buginfo) */ NOFLAGS /* not used */ }; /* * pst_start - open the devices and initialize data for processing */ static int pst_start( int unit, struct peer *peer ) { register struct pstunit *up; struct refclockproc *pp; int fd; char device[20]; /* * Open serial port. Use CLK line discipline, if available. */ snprintf(device, sizeof(device), DEVICE, unit); fd = refclock_open(&peer->srcadr, device, SPEED232, LDISC_CLK); if (fd <= 0) return (0); /* * Allocate and initialize unit structure */ up = emalloc_zero(sizeof(*up)); pp = peer->procptr; pp->io.clock_recv = pst_receive; pp->io.srcclock = peer; pp->io.datalen = 0; pp->io.fd = fd; if (!io_addclock(&pp->io)) { close(fd); pp->io.fd = -1; free(up); return (0); } pp->unitptr = up; /* * Initialize miscellaneous variables */ peer->precision = PRECISION; pp->clockdesc = DESCRIPTION; memcpy((char *)&pp->refid, WWVREFID, 4); return (1); } /* * pst_shutdown - shut down the clock */ static void pst_shutdown( int unit, struct peer *peer ) { register struct pstunit *up; struct refclockproc *pp; pp = peer->procptr; up = pp->unitptr; if (-1 != pp->io.fd) io_closeclock(&pp->io); if (NULL != up) free(up); } /* * pst_receive - receive data from the serial interface */ static void pst_receive( struct recvbuf *rbufp ) { register struct pstunit *up; struct refclockproc *pp; struct peer *peer; l_fp trtmp; u_long ltemp; char ampmchar; /* AM/PM indicator */ char daychar; /* standard/daylight indicator */ char junque[10]; /* "yy/dd/mm/" discard */ char info[14]; /* "frdzycchhSSFT" clock info */ /* * Initialize pointers and read the timecode and timestamp */ peer = rbufp->recv_peer; pp = peer->procptr; up = pp->unitptr; up->lastptr += refclock_gtlin(rbufp, up->lastptr, pp->a_lastcode + BMAX - 2 - up->lastptr, &trtmp); *up->lastptr++ = ' '; *up->lastptr = '\0'; /* * Note we get a buffer and timestamp for each , but only * the first timestamp is retained. */ if (up->tcswitch == 0) pp->lastrec = trtmp; up->tcswitch++; pp->lencode = up->lastptr - pp->a_lastcode; if (up->tcswitch < 3) return; /* * We get down to business, check the timecode format and decode * its contents. If the timecode has invalid length or is not in * proper format, we declare bad format and exit. */ if (pp->lencode < LENPST) { refclock_report(peer, CEVNT_BADREPLY); return; } /* * Timecode format: * "ahh:mm:ss.fffs yy/dd/mm/ddd frdzycchhSSFTttttuuxx" */ if (sscanf(pp->a_lastcode, "%c%2d:%2d:%2d.%3ld%c %9s%3d%13s%4ld", &mchar, &pp->hour, &pp->minute, &pp->second, &pp->nsec, &daychar, junque, &pp->day, info, <emp) != 10) { refclock_report(peer, CEVNT_BADREPLY); return; } pp->nsec *= 1000000; /* * Decode synchronization, quality and last update. If * unsynchronized, set the leap bits accordingly and exit. Once * synchronized, the dispersion depends only on when the clock * was last heard, which depends on the time since last update, * as reported by the clock. */ if (info[9] != '8') pp->leap = LEAP_NOTINSYNC; if (info[12] == 'H') memcpy((char *)&pp->refid, WWVHREFID, 4); else memcpy((char *)&pp->refid, WWVREFID, 4); if (peer->stratum <= 1) peer->refid = pp->refid; if (ltemp == 0) pp->lastref = pp->lastrec; pp->disp = PST_PHI * ltemp * 60; /* * Process the new sample in the median filter and determine the * timecode timestamp. */ if (!refclock_process(pp)) refclock_report(peer, CEVNT_BADTIME); else if (peer->disp > MAXDISTANCE) refclock_receive(peer); } /* * pst_poll - called by the transmit procedure */ static void pst_poll( int unit, struct peer *peer ) { register struct pstunit *up; struct refclockproc *pp; /* * Time to poll the clock. The PSTI/Traconex clock responds to a * "QTQDQMT" by returning a timecode in the format specified * above. Note there is no checking on state, since this may not * be the only customer reading the clock. Only one customer * need poll the clock; all others just listen in. If the clock * becomes unreachable, declare a timeout and keep going. */ pp = peer->procptr; up = pp->unitptr; up->tcswitch = 0; up->lastptr = pp->a_lastcode; if (write(pp->io.fd, "QTQDQMT", 6) != 6) refclock_report(peer, CEVNT_FAULT); if (pp->coderecv == pp->codeproc) { refclock_report(peer, CEVNT_TIMEOUT); return; } refclock_receive(peer); record_clock_stats(&peer->srcadr, pp->a_lastcode); #ifdef DEBUG if (debug) printf("pst: timecode %d %s\n", pp->lencode, pp->a_lastcode); #endif pp->polls++; } #else int refclock_pst_int; #endif /* REFCLOCK */