Lines Matching +full:shared +full:- +full:pin
1 // SPDX-License-Identifier: (GPL-2.0+ OR MIT)
3 /dts-v1/;
5 #include <dt-bindings/gpio/gpio.h>
6 #include <dt-bindings/pinctrl/rockchip.h>
7 #include <dt-bindings/soc/rockchip,vop2.h>
21 stdout-path = "serial2:1500000n8";
24 gmac1_clkin: external-gmac1-clock {
25 compatible = "fixed-clock";
26 clock-frequency = <125000000>;
27 clock-output-names = "gmac1_clkin";
28 #clock-cells = <0>;
31 hdmi-con {
32 compatible = "hdmi-connector";
37 remote-endpoint = <&hdmi_out_con>;
43 compatible = "gpio-leds";
45 led_diy: led-diy {
46 label = "diy-led";
47 default-state = "on";
49 linux,default-trigger = "heartbeat";
50 pinctrl-names = "default";
51 pinctrl-0 = <&diy_led_enable_h>;
52 retain-state-suspended;
56 led_work: led-work {
57 label = "work-led";
58 default-state = "off";
60 pinctrl-names = "default";
61 pinctrl-0 = <&work_led_enable_h>;
62 retain-state-suspended;
67 sdio_pwrseq: sdio-pwrseq {
69 compatible = "mmc-pwrseq-simple";
71 clock-names = "ext_clock";
72 pinctrl-names = "default";
73 pinctrl-0 = <&wifi_enable_h>;
74 reset-gpios = <&gpio2 RK_PC2 GPIO_ACTIVE_LOW>;
77 vbus: vbus-regulator {
78 compatible = "regulator-fixed";
79 regulator-name = "vbus";
80 regulator-always-on;
81 regulator-boot-on;
82 regulator-min-microvolt = <5000000>;
83 regulator-max-microvolt = <5000000>;
87 vcc5v0_sys: vcc5v0-sys-regulator {
88 compatible = "regulator-fixed";
89 regulator-name = "vcc5v0_sys";
90 regulator-always-on;
91 regulator-boot-on;
92 regulator-min-microvolt = <5000000>;
93 regulator-max-microvolt = <5000000>;
94 vin-supply = <&vbus>;
97 vcc3v3_sys: vcc3v3-sys-regulator {
98 compatible = "regulator-fixed";
99 regulator-name = "vcc3v3_sys";
100 regulator-always-on;
101 regulator-boot-on;
102 regulator-min-microvolt = <3300000>;
103 regulator-max-microvolt = <3300000>;
104 vin-supply = <&vcc5v0_sys>;
109 cpu-supply = <&vdd_cpu>;
113 cpu-supply = <&vdd_cpu>;
117 cpu-supply = <&vdd_cpu>;
121 cpu-supply = <&vdd_cpu>;
125 assigned-clocks = <&cru SCLK_GMAC1_RX_TX>, <&cru SCLK_GMAC1_RGMII_SPEED>, <&cru SCLK_GMAC1>;
126 assigned-clock-parents = <&cru SCLK_GMAC1_RGMII_SPEED>, <&cru SCLK_GMAC1>, <&gmac1_clkin>;
128 phy-supply = <&vcc_3v3>;
129 phy-mode = "rgmii";
130 pinctrl-names = "default";
131 pinctrl-0 = <&gmac1m0_miim
137 snps,reset-gpio = <&gpio0 RK_PC3 GPIO_ACTIVE_LOW>;
138 snps,reset-active-low;
140 snps,reset-delays-us = <0 20000 100000>;
143 phy-handle = <&rgmii_phy1>;
148 nextrst-hog {
149 gpio-hog;
151 * GPIO_ACTIVE_LOW + output-low here means that the pin is set
152 * to high, because output-low decides the value pre-inversion.
155 line-name = "nEXTRST";
156 output-low;
161 mali-supply = <&vdd_gpu>;
166 avdd-0v9-supply = <&vdda0v9_image>;
167 avdd-1v8-supply = <&vcca1v8_image>;
173 remote-endpoint = <&vp0_out_hdmi>;
179 remote-endpoint = <&hdmi_con_in>;
193 fcs,suspend-voltage-selector = <1>;
194 regulator-name = "vdd_cpu";
195 regulator-min-microvolt = <800000>;
196 regulator-max-microvolt = <1150000>;
197 regulator-ramp-delay = <2300>;
198 regulator-always-on;
199 regulator-boot-on;
200 vin-supply = <&vcc5v0_sys>;
202 regulator-state-mem {
203 regulator-off-in-suspend;
210 interrupt-parent = <&gpio0>;
212 #clock-cells = <1>;
213 clock-output-names = "rk808-clkout1", "rk808-clkout2";
214 pinctrl-names = "default";
215 pinctrl-0 = <&pmic_int_l>;
216 rockchip,system-power-controller;
217 wakeup-source;
219 vcc1-supply = <&vcc3v3_sys>;
220 vcc2-supply = <&vcc3v3_sys>;
221 vcc3-supply = <&vcc3v3_sys>;
222 vcc4-supply = <&vcc3v3_sys>;
223 vcc5-supply = <&vcc3v3_sys>;
224 vcc6-supply = <&vcc3v3_sys>;
225 vcc7-supply = <&vcc3v3_sys>;
226 vcc8-supply = <&vcc3v3_sys>;
227 vcc9-supply = <&vcc3v3_sys>;
231 regulator-name = "vdd_logic";
232 regulator-always-on;
233 regulator-boot-on;
234 regulator-min-microvolt = <500000>;
235 regulator-max-microvolt = <1350000>;
236 regulator-ramp-delay = <6001>;
237 regulator-initial-mode = <0x2>;
238 regulator-state-mem {
239 regulator-on-in-suspend;
240 regulator-suspend-microvolt = <900000>;
245 regulator-name = "vdd_gpu";
246 regulator-always-on;
247 regulator-boot-on;
248 regulator-min-microvolt = <500000>;
249 regulator-max-microvolt = <1350000>;
250 regulator-ramp-delay = <6001>;
251 regulator-initial-mode = <0x2>;
252 regulator-state-mem {
253 regulator-off-in-suspend;
258 regulator-always-on;
259 regulator-boot-on;
260 regulator-initial-mode = <0x2>;
261 regulator-name = "vcc_ddr";
262 regulator-state-mem {
263 regulator-on-in-suspend;
268 regulator-always-on;
269 regulator-boot-on;
270 regulator-min-microvolt = <500000>;
271 regulator-max-microvolt = <1350000>;
272 regulator-initial-mode = <0x2>;
273 regulator-name = "vdd_npu";
274 regulator-state-mem {
275 regulator-off-in-suspend;
280 regulator-name = "vcc_1v8";
281 regulator-always-on;
282 regulator-boot-on;
283 regulator-min-microvolt = <1800000>;
284 regulator-max-microvolt = <1800000>;
285 regulator-state-mem {
286 regulator-on-in-suspend;
287 regulator-suspend-microvolt = <1800000>;
292 regulator-always-on;
293 regulator-boot-on;
294 regulator-min-microvolt = <900000>;
295 regulator-max-microvolt = <900000>;
296 regulator-name = "vdda0v9_image";
297 regulator-state-mem {
298 regulator-on-in-suspend;
299 regulator-suspend-microvolt = <900000>;
304 regulator-always-on;
305 regulator-boot-on;
306 regulator-min-microvolt = <900000>;
307 regulator-max-microvolt = <900000>;
308 regulator-name = "vdda_0v9";
309 regulator-state-mem {
310 regulator-off-in-suspend;
315 regulator-always-on;
316 regulator-boot-on;
317 regulator-min-microvolt = <900000>;
318 regulator-max-microvolt = <900000>;
319 regulator-name = "vdda0v9_pmu";
320 regulator-state-mem {
321 regulator-on-in-suspend;
322 regulator-suspend-microvolt = <900000>;
327 regulator-always-on;
328 regulator-boot-on;
329 regulator-min-microvolt = <3300000>;
330 regulator-max-microvolt = <3300000>;
331 regulator-name = "vccio_acodec";
332 regulator-state-mem {
333 regulator-off-in-suspend;
338 regulator-always-on;
339 regulator-boot-on;
340 regulator-min-microvolt = <1800000>;
341 regulator-max-microvolt = <3300000>;
342 regulator-name = "vccio_sd";
343 regulator-state-mem {
344 regulator-off-in-suspend;
349 regulator-always-on;
350 regulator-boot-on;
351 regulator-min-microvolt = <3300000>;
352 regulator-max-microvolt = <3300000>;
353 regulator-name = "vcc3v3_pmu";
354 regulator-state-mem {
355 regulator-on-in-suspend;
356 regulator-suspend-microvolt = <3300000>;
361 regulator-always-on;
362 regulator-boot-on;
363 regulator-min-microvolt = <1800000>;
364 regulator-max-microvolt = <1800000>;
365 regulator-name = "vcca_1v8";
366 regulator-state-mem {
367 regulator-off-in-suspend;
372 regulator-always-on;
373 regulator-boot-on;
374 regulator-min-microvolt = <1800000>;
375 regulator-max-microvolt = <1800000>;
376 regulator-name = "vcca1v8_pmu";
377 regulator-state-mem {
378 regulator-off-in-suspend;
383 regulator-always-on;
384 regulator-boot-on;
385 regulator-min-microvolt = <1800000>;
386 regulator-max-microvolt = <1800000>;
387 regulator-name = "vcca1v8_image";
388 regulator-state-mem {
389 regulator-off-in-suspend;
394 regulator-name = "vcc_3v3";
395 regulator-state-mem {
396 regulator-off-in-suspend;
401 regulator-name = "vcc3v3_sd";
403 regulator-state-mem {
404 regulator-on-in-suspend;
414 * pin 80 - i2c1_scl_m0, pullup to vcc3v3_pmu
415 * pin 82 - i2c1_sda_m0, pullup to vcc3v3_pmu
423 * pin 56 - i2c2_scl_m1, pullup to vcc_3v3, shared with i2s1_8ch
424 * pin 58 - i2c2_sda_m1, pullup to vcc_3v3
427 pinctrl-names = "default";
428 pinctrl-0 = <&i2c2m1_xfer>;
434 * pin 35 - i2c3_scl_m0, pullup to vcc_3v3
435 * pin 36 - i2c3_sda_m0, pullup to vcc_3v3
443 * pin 45 - i2c4_scl_m1
444 * pin 47 - i2c4_sda_m1
447 pinctrl-names = "default";
448 pinctrl-0 = <&i2c4m1_xfer>;
458 * pin 24 - i2s1_sdi1_m1
459 * pin 25 - i2s1_sdo0_m1
460 * pin 26 - i2s1_lrck_tx_m1
461 * pin 27 - i2s1_sdi0_m1
462 * pin 29 - i2s1_sdi3_m1
463 * pin 30 - i2s1_sdi2_m1
464 * pin 40 - i2s1_sdo1_m1, shared with spi3
465 * pin 41 - i2s1_sdo2_m1
466 * pin 49 - i2s1_sclk_tx_m1
467 * pin 50 - i2s1_mclk_m1
468 * pin 56 - i2s1_sdo3_m1, shared with i2c2
471 pinctrl-names = "default";
472 pinctrl-0 = <&i2s1m1_sclktx &i2s1m1_sclkrx
482 rgmii_phy1: ethernet-phy@0 {
483 compatible = "ethernet-phy-ieee802.3-c22";
490 pinctrl-names = "default";
491 pinctrl-0 = <&pcie_reset_h>;
492 reset-gpios = <&gpio1 RK_PB2 GPIO_ACTIVE_HIGH>;
497 bt_enable_h: bt-enable-h {
501 bt_host_wake_l: bt-host-wake-l {
505 bt_wake_l: bt-wake-l {
511 work_led_enable_h: work-led-enable-h {
515 diy_led_enable_h: diy-led-enable-h {
521 pcie_clkreq_h: pcie-clkreq-h {
524 pcie_reset_h: pcie-reset-h {
530 pmic_int_l: pmic-int-l {
535 sdio-pwrseq {
536 wifi_enable_h: wifi-enable-h {
543 pmuio1-supply = <&vcc3v3_pmu>;
544 pmuio2-supply = <&vcc3v3_pmu>;
545 vccio1-supply = <&vcc_3v3>;
546 vccio2-supply = <&vcc_1v8>;
547 vccio3-supply = <&vccio_sd>;
548 vccio4-supply = <&vcc_1v8>;
549 vccio5-supply = <&vcc_3v3>;
550 vccio6-supply = <&vcc_3v3>;
551 vccio7-supply = <&vcc_3v3>;
557 * pin 94 - saradc_vin3
558 * pin 96 - saradc_vin2
561 vref-supply = <&vcca_1v8>;
566 bus-width = <8>;
567 mmc-hs200-1_8v;
568 non-removable;
569 vmmc-supply = <&vcc_3v3>;
570 vqmmc-supply = <&vcc_1v8>;
575 broken-cd;
576 bus-width = <4>;
577 cap-sd-highspeed;
578 disable-wp;
579 pinctrl-names = "default";
580 pinctrl-0 = <&sdmmc0_bus4 &sdmmc0_clk &sdmmc0_cmd &sdmmc0_det>;
581 vqmmc-supply = <&vccio_sd>;
586 bus-width = <4>;
587 cap-sd-highspeed;
588 cap-sdio-irq;
589 keep-power-in-suspend;
590 mmc-pwrseq = <&sdio_pwrseq>;
591 non-removable;
592 pinctrl-names = "default";
593 pinctrl-0 = <&sdmmc1_bus4 &sdmmc1_cmd &sdmmc1_clk>;
594 sd-uhs-sdr50;
595 vmmc-supply = <&vcc3v3_sys>;
596 vqmmc-supply = <&vcc_1v8>;
602 * pin 37 - spi3_cs1_m0
603 * pin 38 - spi3_clk_m0
604 * pin 39 - spi3_cs0_m0
605 * pin 40 - spi3_miso_m0, shared with i2s1_8ch
606 * pin 44 - spi3_mosi_m0
617 pinctrl-names = "default";
618 pinctrl-0 = <&uart1m0_xfer &uart1m0_ctsn &uart1m0_rtsn>;
619 uart-has-rtscts;
623 compatible = "brcm,bcm43438-bt";
625 clock-names = "lpo";
626 device-wakeup-gpios = <&gpio2 RK_PC1 GPIO_ACTIVE_HIGH>;
627 host-wakeup-gpios = <&gpio2 RK_PC0 GPIO_ACTIVE_HIGH>;
628 shutdown-gpios = <&gpio2 RK_PB7 GPIO_ACTIVE_HIGH>;
629 pinctrl-names = "default";
630 pinctrl-0 = <&bt_host_wake_l &bt_wake_l &bt_enable_h>;
631 vbat-supply = <&vcc3v3_sys>;
632 vddio-supply = <&vcca1v8_pmu>;
638 * pin 51 - uart2_rx_m0
639 * pin 55 - uart2_tx_m0
647 * pin 46 - uart7_tx_m2
648 * pin 47 - uart7_rx_m2
651 pinctrl-names = "default";
652 pinctrl-0 = <&uart7m2_xfer>;
670 assigned-clocks = <&cru DCLK_VOP0>, <&cru DCLK_VOP1>;
671 assigned-clock-parents = <&pmucru PLL_HPLL>, <&cru PLL_VPLL>;
682 remote-endpoint = <&hdmi_in_vp0>;