Lines Matching +full:usb2 +full:- +full:phy0

1 // SPDX-License-Identifier: (GPL-2.0+ OR MIT)
4  * (DB-88F3720-DDR3)
7  * Gregory CLEMENT <gregory.clement@free-electrons.com>
14 /dts-v1/;
16 #include <dt-bindings/gpio/gpio.h>
17 #include "armada-372x.dtsi"
20 	model = "Marvell Armada 3720 Development Board DB-88F3720-DDR3";
21 	compatible = "marvell,armada-3720-db", "marvell,armada3720", "marvell,armada3700";
24 		stdout-path = "serial0:115200n8";
32 	exp_usb3_vbus: usb3-vbus {
33 		compatible = "regulator-fixed";
34 		regulator-name = "usb3-vbus";
35 		regulator-min-microvolt = <5000000>;
36 		regulator-max-microvolt = <5000000>;
37 		enable-active-high;
38 		regulator-always-on;
42 	usb3_phy: usb3-phy {
43 		compatible = "usb-nop-xceiv";
44 		vcc-supply = <&exp_usb3_vbus>;
48 		compatible = "regulator-gpio";
49 		regulator-name = "vcc_sd1";
50 		regulator-min-microvolt = <1800000>;
51 		regulator-max-microvolt = <3300000>;
52 		regulator-boot-on;
55 		gpios-states = <0>;
58 		enable-active-high;
61 	vcc_sd_reg2: regulator-vmcc {
62 		compatible = "regulator-fixed";
63 		regulator-name = "vcc_sd2";
64 		regulator-min-microvolt = <3300000>;
65 		regulator-max-microvolt = <3300000>;
66 		regulator-boot-on;
67 		enable-active-high;
74 	pinctrl-names = "default";
75 	pinctrl-0 = <&rgmii_pins>;
76 	phy-mode = "rgmii-id";
77 	phy = <&phy0>;
83 	phy-mode = "sgmii";
89 	pinctrl-names = "default";
90 	pinctrl-0 = <&i2c1_pins>;
95 		gpio-controller;
96 		#gpio-cells = <2>;
120 	phy0: ethernet-phy@0 {  label
124 	phy1: ethernet-phy@1 {
129 /* CON15(V2.0)/CON17(V1.4) : PCIe / CON15(V2.0)/CON12(V1.4) :mini-PCIe */
131 	pinctrl-names = "default";
132 	pinctrl-0 = <&pcie_reset_pins &pcie_clkreq_pins>;
133 	reset-gpios = <&gpiosb 3 GPIO_ACTIVE_LOW>;
143 	non-removable;
144 	bus-width = <8>;
145 	mmc-ddr-1_8v;
146 	mmc-hs400-1_8v;
147 	marvell,pad-type = "fixed-1-8v";
153 	wp-inverted;
154 	cd-gpios = <&gpiosb 2 GPIO_ACTIVE_LOW>;
155 	bus-width = <4>;
156 	marvell,pad-type = "sd";
157 	vqmmc-supply = <&vcc_sd_reg1>;
158 	vmmc-supply = <&vcc_sd_reg2>;
164 	pinctrl-names = "default";
165 	pinctrl-0 = <&spi_quad_pins>;
168 		compatible = "jedec,spi-nor";
170 		spi-max-frequency = <108000000>;
171 		spi-rx-bus-width = <4>;
172 		spi-tx-bus-width = <4>;
175 			compatible = "fixed-partitions";
176 			#address-cells = <1>;
177 			#size-cells = <1>;
183 				label = "U-boot Env";
199 	pinctrl-names = "default";
200 	pinctrl-0 = <&uart1_pins>;
206 	pinctrl-names = "default";
207 	pinctrl-0 = <&uart2_pins>;
212 &usb2 {
219 	usb-phy = <&usb3_phy>;