Lines Matching +full:read +full:- +full:delay

1 // SPDX-License-Identifier: GPL-2.0
3  * Device Tree file for D-Link DNS-313 1-Bay Network Storage Enclosure
6 /dts-v1/;
9 #include <dt-bindings/input/input.h>
10 #include <dt-bindings/thermal/thermal.h>
13 	model = "D-Link DNS-313 1-Bay Network Storage Enclosure";
14 	compatible = "dlink,dns-313", "cortina,gemini";
15 	#address-cells = <1>;
16 	#size-cells = <1>;
19 		/* 64 MB SDRAM in a Nanya NT5DS32M16BS-6K package */
25 		mdio-gpio0 = &mdio0;
30 		stdout-path = "uart0:19200n8";
34 		compatible = "gpio-keys";
36 		button-esc {
37 			debounce-interval = <100>;
38 			wakeup-source;
46 		compatible = "gpio-leds";
47 		led-power {
50 			default-state = "on";
51 			linux,default-trigger = "heartbeat";
53 		led-disk-blue {
56 			default-state = "off";
58 		led-disk-green {
61 			default-state = "off";
62 			linux,default-trigger = "disk-read";
64 		led-disk-red {
67 			default-state = "off";
68 			linux,default-trigger = "disk-write";
73 	 * This is a ADDA AD0405GB-G73 fan @3000 and 6000 RPM.
75 	fan0: gpio-fan {
76 		compatible = "gpio-fan";
79 		gpio-fan,speed-map = <0 0>, <3000 1>, <6000 2>;
80 		#cooling-cells = <2>;
85 	 * a GPIO-controlled USB VBUS detect
88 		compatible = "gpio-usb-b-connector", "usb-b-connector";
89 		#phy-cells = <0>;
90 		vbus-gpios = <&gpio0 18 GPIO_ACTIVE_LOW>;
93 	/* Global Mixed-Mode Technology G751 mounted on GPIO I2C */
95 		compatible = "i2c-gpio";
96 		sda-gpios = <&gpio0 15 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
97 		scl-gpios = <&gpio0 16 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
98 		#address-cells = <1>;
99 		#size-cells = <0>;
101 		g751: temperature-sensor@48 {
104 			#thermal-sensor-cells = <0>;
108 	thermal-zones {
109 		chassis-thermal {
111 			polling-delay = <20000>;
113 			polling-delay-passive = <2000>;
115 			thermal-sensors = <&g751>;
119 				chassis_alert0: chassis-alert0 {
125 				chassis_alert1: chassis-alert1 {
131 				chassis_crit: chassis-crit {
139 			cooling-maps {
142 					cooling-device = <&fan0 1 1>;
146 					cooling-device = <&fan0 2 2>;
153 		compatible = "virtual,mdio-gpio";
157 		#address-cells = <1>;
158 		#size-cells = <0>;
161 		phy0: ethernet-phy@1 {
163 			device_type = "ethernet-phy";
173 			compatible = "cortina,gemini-flash", "jedec-flash";
176 			#address-cells = <1>;
177 			#size-cells = <1>;
185 				read-only;
190 				read-only;
195 				read-only;
203 				gpio0_default_pins: pinctrl-gpio0 {
222 				gpio1_default_pins: pinctrl-gpio1 {
229 				pinctrl-gmii {
240 						skew-delay = <0>;
244 						skew-delay = <10>;
248 						skew-delay = <15>;
252 						skew-delay = <7>;
256 						skew-delay = <10>;
266 						skew-delay = <7>;
271 						skew-delay = <5>;
276 						drive-strength = <16>;
284 			cortina,gemini-ata-muxmode = <0>;
285 			cortina,gemini-enable-sata-bridge;
290 			pinctrl-names = "default";
291 			pinctrl-0 = <&gpio0_default_pins>;
295 			pinctrl-names = "default";
296 			pinctrl-0 = <&gpio1_default_pins>;
302 			ethernet-port@0 {
303 				phy-mode = "rgmii";
304 				phy-handle = <&phy0>;
306 			ethernet-port@1 {
318 			usb-phy = <&usb1_phy>;
319 			pinctrl-names = "default";
320 			pinctrl-0 = <&usb_default_pins>;