Lines Matching +full:pio +full:- +full:mode

4  * This file is dual-licensed: you can use it either under the terms
43 /dts-v1/;
44 #include "sun7i-a20.dtsi"
45 #include "sunxi-common-regulators.dtsi"
47 #include <dt-bindings/gpio/gpio.h>
48 #include <dt-bindings/interrupt-controller/irq.h>
52 	compatible = "allwinner,i12-tvbox", "allwinner,sun7i-a20";
59 		stdout-path = "serial0:115200n8";
63 		compatible = "gpio-leds";
65 		led-0 {
67 			gpios = <&pio 7 9 GPIO_ACTIVE_LOW>;
70 		led-1 {
72 			gpios = <&pio 7 20 GPIO_ACTIVE_HIGH>;
77 		compatible = "regulator-fixed";
78 		regulator-name = "vmmc3";
79 		regulator-min-microvolt = <3300000>;
80 		regulator-max-microvolt = <3300000>;
81 		enable-active-high;
82 		gpio = <&pio 7 2 GPIO_ACTIVE_HIGH>;
85 	reg_vmmc3_io: vmmc3-io {
86 		compatible = "regulator-fixed";
87 		regulator-name = "vmmc3-io";
88 		regulator-min-microvolt = <3300000>;
89 		regulator-max-microvolt = <3300000>;
90 		/* This controls VCC-PI, must be always on! */
91 		regulator-always-on;
92 		enable-active-high;
93 		gpio = <&pio 7 12 GPIO_ACTIVE_HIGH>;
96 	reg_gmac_3v3: gmac-3v3 {
97 		compatible = "regulator-fixed";
98 		regulator-name = "gmac-3v3";
99 		regulator-min-microvolt = <3300000>;
100 		regulator-max-microvolt = <3300000>;
101 		startup-delay-us = <50000>;
102 		enable-active-high;
103 		gpio = <&pio 7 21 GPIO_ACTIVE_HIGH>;
116 	pinctrl-names = "default";
117 	pinctrl-0 = <&gmac_mii_pins>;
118 	phy-handle = <&phy1>;
119 	phy-mode = "mii";
120 	phy-supply = <&reg_gmac_3v3>;
128 		compatible = "x-powers,axp209";
130 		interrupt-parent = <&nmi_intc>;
133 		interrupt-controller;
134 		#interrupt-cells = <1>;
139 	pinctrl-names = "default";
140 	pinctrl-0 = <&ir0_rx_pin>;
145 	phy1: ethernet-phy@1 {
151 	vmmc-supply = <&reg_vcc3v3>;
152 	bus-width = <4>;
153 	cd-gpios = <&pio 7 1 GPIO_ACTIVE_LOW>; /* PH1 */
158 	vmmc-supply = <&reg_vmmc3>;
159 	bus-width = <4>;
160 	non-removable;
165 		compatible = "brcm,bcm4329-fmac";
166 		interrupt-parent = <&pio>;
168 		interrupt-names = "host-wake";
189 	pinctrl-names = "default";
190 	pinctrl-0 = <&uart0_pb_pins>;
195 	usb1_vbus-supply = <&reg_usb1_vbus>;
196 	usb2_vbus-supply = <&reg_usb2_vbus>;